Nissan Juke F15. Manual — part 805
FSU-18
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
• To install rebound stopper (1), insert it with the protrusion aligned
with the hole of member stay (2).
• To install member stay and mounting bolts of front suspension
member, temporarily tighten the bolts before tightening to the
specified torque, referring to the tightening method and the numer-
ical order shown below:
• Perform final tightening of bolts and nuts at the vehicle installation
position (rubber bushing), under unladen conditions with tires on level ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000012199129
INSPECTION AFTER REMOVAL
Check front suspension member for cracks, wear or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connector. Refer to
BRC-147, "FRONT WHEEL SENSOR :
.
2. Check wheel alignment. Refer to
.
3. Adjust neutral position of steering angle sensor. Refer to
.
JPEIA0248ZZ
Temporary tightening
: 1
→ 2
Final tightening
(Specified torque)
: 3
→ 4 → 5 → 6 → 7 → 8 → 9 → 10 → 11 → 12
: Vehicle front
JPEIA0249GB
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-19
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000012199130
Measure value under unladen*
2
conditions.
*1: A difference when assuming the left side a standard.
*2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000012199131
Wheelarch Height
INFOID:0000000012199132
FOR USA MODELS
EXCEPT NISMO
Item
Standard
Axle type
2WD
AWD
Camber
Degree minute (Decimal degree)
Minimum
–1
° 10′ (–1.16°)
Nominal
–0
° 25′ (–0.42°)
Maximum
0
° 20′ (0.33°)
Left and right difference*
1
–0
° 45′ (–0.75°) - 0° 45′ (0.75°)
Caster
Degree minute (Decimal degree)
Minimum
3
° 45′ (3.75°)
3
° 50′ (3.84°)
Nominal
4
° 30′ (4.50°)
4
° 35′ (4.58°)
Maximum
5
° 15′ (5.25°)
5
° 20′ (5.33°)
Left and right difference*
1
–0
° 45′ (–0.75°) - 0° 45′ (0.75°)
Kingpin inclination
Degree minute (Decimal degree)
Minimum
10
° 40′ (10.67°)
Nominal
11
° 25′ (11.42°)
Maximum
12
° 10′ (12.16°)
Toe-in
Total toe-in
Distance
Minimum
0 mm (0.00 in)
Nominal
In 2 mm (In 0.08 in)
Maximum
In 4 mm (In 0.16 in)
Total toe-angle
Degree minute (Decimal degree)
Minimum
Out 0
° 02′ 00″ (Out 0.03°)
Nominal
In 0
° 10′ 00″ (In 0.17°)
Maximum
In 0
° 22′ 00″ (In 0.36°)
Item
Standard
Swing torque
0.5 – 4.9 N·m (0.06 – 0.49 kg-m, 5 – 43 in-lb)
Measurement on spring balance
15.4 – 150.8 N (1.6 – 15.3 kg, 3.5 – 33.8 lb)
Axial end play
0 mm (0 in)
Item
Standard
Axle type
2WD
AWD
Transmission
M/T
CVT
Front (Hf)
734 mm (28.90 in)
735 mm (28.94 in)
734 mm (28.90 in)
FSU-20
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
NISMO
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
FOR CANADA MODELS
EXCEPT NISMO
Rear (Hr)
745 mm (29.33 in)
746 mm (29.37 in)
741 mm (29.17 in)
Item
Standard
Axle type
2WD
AWD
Transmission
M/T
CVT
SFA746B
Item
NISMO
NISMO RS
NISMO
NISMO RS
Axle type
2WD
AWD
Front (Hf)
724 mm (28.50 in)
725 mm (28.54 in)
724 mm (28.50 in)
Rear (Hr)
738 mm (29.06 in)
739 mm (29.09 in)
735 mm (28.94 in)
SFA746B
Item
Standard
Axle type
2WD
AWD
Transmission
M/T
CVT
Front (Hf)
735 mm (28.94 in)
735 mm (28.94 in)
735 mm (28.94 in)
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-21
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
NISMO
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Rear (Hr)
745 mm (29.33 in)
746 mm (29.37 in)
741 mm (29.17 in)
Item
Standard
Axle type
2WD
AWD
Transmission
M/T
CVT
SFA746B
Item
NISMO
NISMO RS
NISMO
NISMO RS
Axle type
2WD
AWD
Front (Hf)
727 mm (28.62 in)
725 mm (28.54 in)
726 mm (28.58 in)
724 mm (28.50 in)
Rear (Hr)
740 mm (29.13 in)
740 mm (29.13 in)
735 mm (28.94 in)
735 mm (28.94 in)
SFA746B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст