Nissan Juke F15. Manual — part 136
VDC OFF SWITCH
BRC-135
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
3. Select “ABS”, “DATA MONITOR” and “OFF SW” according to this order. Check the VDC OFF switch sig-
nal.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 5.
5.
CHECK TERMINAL
• Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with
harness connector.
• Check the VDC OFF switch pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> Replace the ABS actuator and electric unit (control unit). Refer to
.
NO
>> Repair / replace harness, connector, or terminal.
Component Inspection
INFOID:0000000012199731
1.
CHECK VDC OFF SWITCH
1. Turn the ignition switch OFF.
2. Disconnect triple switch harness connector.
3. Check the continuity between VDC OFF switch connector terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the VDC OFF switch. Refer to
BRC-157, "Removal and Installation"
.
Condition
DATA MONITOR
When VDC OFF switch is pressed and VDC OFF indicator
lamp in combination meter is in ON status
On
When VDC OFF switch is pressed and VDC OFF indicator
lamp in combination meter is in OFF status
Off
VDC OFF switch
Condition
Continuity
Terminal
1 – 2
When VDC OFF switch is pressed
Existed
When VDC OFF switch is not pressed
Not existed
BRC-136
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
ABS WARNING LAMP
ABS WARNING LAMP
Component Function Check
INFOID:0000000012199732
1.
CHECK ABS WARNING LAMP FUNCTION
Check that ABS warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
BRC-136, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000012199733
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
BRC-129, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair / replace harness, connector, fuse, or fusible link.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK ABS WARNING LAMP SIGNAL
With CONSULT
1. Select “ABS”, “DATA MONITOR” and “ABS WARN LAMP” according to this order.
2. Turn the ignition switch OFF.
3. Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON and then
changes to “Off”.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> Check the combination meter. Refer to
NO
>> Replace the ABS actuator and electric unit (control unit). Refer to
.
BRAKE WARNING LAMP
BRC-137
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
BRAKE WARNING LAMP
Component Function Check
INFOID:0000000012199734
1.
CHECK BRAKE WARNING LAMP FUNCTION (1)
Check that brake warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Proceed to
BRC-137, "Diagnosis Procedure"
2.
CHECK BRAKE WARNING LAMP FUNCTION (2)
Check that brake warning lamp in combination meter turns ON/OFF when parking brake is operated.
NOTE:
Brake warning lamp turns ON when parking brake is operated (when parking brake switch is ON).
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check the parking brake switch system. Refer to
BRC-132, "Diagnosis Procedure"
.
3.
CHECK BRAKE WARNING LAMP FUNCTION (3)
Check that brake warning lamp in combination meter turns ON/OFF when brake fluid level switch is operated
while brake fluid level in reservoir tank is with the specified level.
NOTE:
Brake warning lamp turns ON when brake fluid is less than the specified level (when brake fluid level switch is
ON).
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Check the brake fluid level switch system. Refer to
BRC-113, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000012199735
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
BRC-129, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair / replace harness, connector, fuse, or fusible link.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK COMBINATION METER
Check the combination meter. Refer to
Is the inspection result normal?
YES
>> Replace the ABS actuator and electric unit (control unit). Refer to
.
NO
>> Repair or replace combination meter. Refer to
BRC-138
< DTC/CIRCUIT DIAGNOSIS >
[WITH VDC]
VDC WARNING LAMP
VDC WARNING LAMP
Component Function Check
INFOID:0000000012199736
1.
CHECK VDC WARNING LAMP FUNCTION
Check that VDC warning lamp in combination meter turns ON for approx. 1 second after ignition switch is
turned ON.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to diagnosis procedure. Refer to
BRC-138, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000012199737
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Perform the trouble diagnosis for ABS actuator and electric unit (control unit) power supply and ground circuit.
BRC-129, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair / replace harness, connector, fuse, or fusible link.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ABS”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK VDC WARNING LAMP SIGNAL
With CONSULT
1. Select “ABS”, “DATA MONITOR” and “SLIP/VDC LAMP” according to this order.
2. Turn the ignition switch OFF.
3. Check that data monitor displays “On” for approx. 1 second after ignition switch is turned ON, and then
changes to “Off”.
CAUTION:
Never start engine.
Is the inspection result normal?
YES
>> Check the combination meter. Refer to
NO
>> Replace the ABS actuator and electric unit (control unit). Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст