Nissan Juke F15. Manual — part 226
DLK-84
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
KEY WARNING LAMP
KEY WARNING LAMP
Component Function Check
INFOID:0000000012196650
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “INDICATOR” in “ACTIVE TEST” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Key warning lamp is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196651
1.
CHECK KEY WARNING LAMP
MWI-21, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Monitor item
Status
INDICATOR
KEY ON
Key warning lamp
Turns ON
KEY IND
Blinks
OFF
Turns OFF
REMOTE KEYLESS ENTRY RECEIVER
DLK-85
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
Component Function Check
INFOID:0000000012196652
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “RKE OPE COUN1” in “DATA MONITOR” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Remote keyless entry receiver is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196653
1.
CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect remote keyless entry receiver connector.
3. Check voltage between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• 10 A fuse (No. 7)
• Harness for open or short between remote keyless entry receiver and battery
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
Monitor item
Condition
RKE OPE COUN1
Checks whether value changes when operating Intelligent Key
(+)
(–)
Voltage
Remote keyless entry receiver
Connector
Terminal
M75
1
Ground
Battery voltage
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
18
M75
4
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
18
Existed
DLK-86
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
4.
CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Reconnect BCM connector and remote keyless entry receiver connector.
2. Check signal between remote keyless entry receiver harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace remote keyless entry receiver.
5.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT
1. Disconnect BCM connector and remote keyless entry receiver connector.
2. Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
6.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
(+)
(–)
Condition
Signal
(Reference value)
Remote keyless entry receiver
Connector
Terminal
M75
2
Ground
Waiting
12 V
Press the Intelligent
Key lock or unlock
button
JMMIA0572GB
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
38
M75
2
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
38
Not existed
SHIFT P WARNING LAMP
DLK-87
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SHIFT P WARNING LAMP
Component Function Check
INFOID:0000000012196654
1.
CHECK FUNCTION
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “LCD” in “ACTIVE TEST” mode.
3. Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Shift P warning lamp is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012196655
1.
CHECK SHIFT P WARNING LAMP
MWI-21, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
.
>> INSPECTION END
Monitor item
Status
LCD
SFT P
Shift P warning lamp
Turns ON
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст