Nissan Juke F15. Manual — part 1339
TM-546
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CVT SHIFT SELECTOR
REMOVAL AND INSTALLATION
CVT SHIFT SELECTOR
Exploded View
INFOID:0000000012201237
Removal and Installation
INFOID:0000000012201238
REMOVAL
CAUTION:
Always apply the parking brake before performing removal and installation.
1. Disconnect battery cable from negative terminal. Refer to
PG-105, "Removal and Installation"
.
2. Shift the selector lever to “N” position.
3. Remove the center console. Refer to
IP-24, "Removal and Installation"
.
4. Disconnect the CVT shift selector connector.
5. Shift the selector lever to “P” position.
1.
Selector lever knob
2.
Lock pin
3.
Knob cover
4.
Position indication panel
5.
CVT shift selector assembly
6.
Detent switch
7.
Park position switch
8.
Shift lock unit
9.
Position indicator bulb
:N·m (kg-m, in-lb)
JSDIA6663GB
CVT SHIFT SELECTOR
TM-547
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
6. Disconnect the tip (A) of control cable and remove socket (B)
from the CVT shift selector assembly.
7. Remove the CVT shift selector assembly mounting bolts.
8. Remove the CVT shift selector assembly from the vehicle.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When connecting the control cable (1) to the CVT shift selector
assembly (2), face the grooved surface of the rib (A) up and insert
the control cable until it stops.
Disassembly and Assembly
INFOID:0000000012201239
DISASSEMBLY
CAUTION:
Confirm the installation condition of wiring before disassembly.
1. Slide the selector lever knob cover (1) down.
CAUTION:
Never damage the knob cover.
2. Pull out the lock pin (2).
3. Pull the selector lever knob (3) and knob cover upwards to
remove them.
4. Remove the position lamp.
5. Disengage the hooks (A) (4 locations), and lift up the position
indication panel (1) to separate it from the CVT shift selector
assembly (2).
CAUTION:
Never damage the CVT shift selector assembly.
JSDIA4220ZZ
JSDIA1624ZZ
JSDIA2401ZZ
JSDIA1802ZZ
TM-548
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CVT SHIFT SELECTOR
6. Remove shift lock unit mounting screws (
).
7. Remove the shift lock unit (1) from the CVT shift selector assem-
bly.
8. Disconnect shift lock solenoid harness connector, park position
switch harness connector, and detent switch harness connector.
9. Remove park position switch (1) and detent switch (2) from shift
lock unit.
CAUTION:
Never damage pawls.
ASSEMBLY
Note the following, and assemble in the reverse order of disassembly.
• Follow the procedure below and place the selector knob onto the CVT shift selector.
1. Install the lock pin (2) onto the selector lever knob (3).
2. Install the knob cover (1) onto the selector lever knob.
3. Press the selector lever knob onto the selector lever until it
clicks.
CAUTION:
• When pressing the selector lever knob onto the selector
lever, never press the selector lever knob button.
• Never strike the selector lever knob to press it into place.
Inspection
INFOID:0000000012201240
INSPECTION AFTER INSTALLATION
Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to
.
JSDIA6479ZZ
JSDIA6480ZZ
JSDIA6481ZZ
JSDIA2401ZZ
CONTROL CABLE
TM-549
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL CABLE
Exploded View
INFOID:0000000012201241
Removal and Installation
INFOID:0000000012201242
CAUTION:
Always apply the parking brake before performing removal and installation.
REMOVAL
1. Apply the parking brake.
CAUTION:
Make sure the vehicle cannot move with the parking brake applied.
2. Remove the center console. Refer to
IP-24, "Removal and Installation"
.
3. Disconnect the tip (A) of control cable and remove socket (B)
from the CVT shift selector assembly.
1.
Lock plate
2.
Bracket
3.
Transaxle assembly
4.
Control cable
5.
Bracket
6.
CVT shift selector assembly
A: Manual lever
B: Grommet
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSDIA6076GB
JSDIA4220ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст