Nissan Juke F15. Manual — part 799
FL-26
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EVAP CANISTER
EVAP CANISTER
2WD
2WD : Hydraulic Layout
INFOID:0000000012197597
EVAPORATIVE EMISSION LINE DRAWING
JPBIA4890ZZ
EVAP CANISTER
FL-27
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
NOTE:
Do not use soapy water or any type of solvent while installing vacuum hose or purge hoses.
2WD : Exploded View
INFOID:0000000012197598
2WD : Removal and Installation
INFOID:0000000012197599
REMOVAL
1. Disconnect harness connectors (EVAP control pressure sensor and EVAP canister vent control valve) and
EVAP canister hoses.
2. Remove EVAP canister fixing bolt.
3. Remove EVAP canister.
NOTE:
EVAP canister vent control valve and EVAP control pressure sensor can be removed without removing
the EVAP canister.
INSTALLATION
CAUTION:
Do not reuse O-rings.
Install in the reverse order of removal.
1.
EVAP canister purge volume control
solenoid valve
2.
EVAP service port
3.
EVAP canister
4.
EVAP control pressure sensor
5.
EVAP canister vent control valve
6.
EAVP line
7.
Fuel line
1.
EVAP canister
2.
EVAP control pressure sensor
3.
O-ring
4.
O-ring
5.
EVAP canister vent control valve
6.
EVAP canister hose
7.
Canister filter
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JPBIA4877GB
FL-28
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EVAP CANISTER
NOTE:
Tighten EVAP canister fixing bolt to the specified torque.
2WD : Disassembly and Assembly
INFOID:0000000012197600
DISASSEMBLY
1. Disengage the pawl and turn EVAP canister vent control valve
counterclockwise.
• Lock (A)
• Unlock (B)
2. Remove the EVAP canister vent control valve.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
Always replace O-ring with a new one.
2WD : Inspection
INFOID:0000000012197601
Check EVAP canister as per the following:
1. Block port (B).
2. Blow air into port (A) and check that it flows freely out of port (C).
3. Release blocked port (B).
4. Apply vacuum pressure to port (B) and check that vacuum pres-
sure exists at the ports (A) and (C).
5. Block port (A) and (B).
6. Apply pressure to port (C) and check that there is no leakage.
AWD
AWD : Hydraulic Layout
INFOID:0000000012197602
EVAPORATIVE EMISSION LINE DRAWING
PBIB3091E
PBIB1212E
EVAP CANISTER
FL-29
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
NOTE:
Do not use soapy water or any type of solvent while installing vacuum hose or purge hoses.
1.
EVAP canister purge volume control
solenoid valve
2.
EVAP service port
3.
EVAP canister
4.
EVAP control pressure sensor
5.
EVAP canister vent control valve
6.
EAVP line
7.
Fuel line
JPBIA4891ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст