Nissan Juke F15. Manual — part 781
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
FAX-63
< SYMPTOM DIAGNOSIS >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000012201548
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×: Applicable
Reference
—
(2WD),
(A
WD)
—
—
NVH in
FAX
and FS
U sections
Re
fe
r to
FRO
N
T A
X
L
E in
th
is
ch
art
NVH in WT
section
NVH in WT
section
Refe
r to
DRIVE
SHAFT i
n t
hi
s cha
rt
NVH in BR
section
NVH in ST
section
Possible cause and SUSPECTED PARTS
Exc
e
ss
iv
e j
oin
t a
ng
le
Jo
in
t s
lid
in
g re
si
stan
ce
Im
ba
lan
ce
Im
pro
per in
st
a
lla
tion
, lo
os
en
es
s
Part
s int
erference
Whe
el
be
ari
ng
da
m
age
FRONT AXLE AND F
R
ONT
SUSPENSI
ON
FRONT AXLE
TIRE
ROA
D
WHEEL
DRIVE SHA
F
T
BRAKE
STEERI
N
G
Symptom
DRIVE
SHAFT
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
FRONT
AXLE
Noise
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
FAX-64
< PERIODIC MAINTENANCE >
[TYPE 2]
FRONT WHEEL HUB AND KNUCKLE
PERIODIC MAINTENANCE
FRONT WHEEL HUB AND KNUCKLE
Inspection
INFOID:0000000012201549
COMPONENT PART
Check that the mounting conditions (looseness, backlash) of each component and component conditions
(wear, damage) are normal.
WHEEL HUB ASSEMBLY (BEARING-INTEGRATED TYPE)
Check the following items, and replace the part if necessary.
• Move wheel hub assembly in the axial direction by hand. Check there is no looseness of wheel bearing.
• Rotate wheel hub assembly and check there is no unusual noise or other irregular conditions. If there is any
of irregular conditions, replace wheel hub assembly.
Axial end play
: Refer to
FRONT DRIVE SHAFT
FAX-65
< PERIODIC MAINTENANCE >
[TYPE 2]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
FRONT DRIVE SHAFT
Inspection
INFOID:0000000012201550
Check the following items, and replace the part if necessary.
• Check drive shaft mounting point and joint for looseness and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occurs from drive shaft.
• Check boot for cracks and other damage.
FAX-66
< REMOVAL AND INSTALLATION >
[TYPE 2]
FRONT WHEEL HUB AND KNUCKLE
REMOVAL AND INSTALLATION
FRONT WHEEL HUB AND KNUCKLE
Exploded View
INFOID:0000000012201551
Removal and Installation
INFOID:0000000012201552
REMOVAL
1. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
2. Remove wheel sensor and sensor harness. Refer to
BRC-147, "FRONT WHEEL SENSOR : Exploded
.
3. Remove lock plate from strut assembly. Refer to
BR-25, "FRONT : Removal and Installation"
4. Remove caliper assembly. Hang caliper assembly not to interfere with work. Refer to
CALIPER ASSEMBLY : Removal and Installation"
.
CAUTION:
Never depress brake pedal while brake caliper is removed.
5. Remove disc rotor.
CAUTION:
1.
Steering knuckle
2.
Splash guard
3.
Hub bolt
4.
Wheel hub assembly (Bearing-inte-
grated type)
5.
Disc rotor
6.
Wheel hub lock nut
7.
Adjusting cap
8.
Cotter pin
A. Tightening must be done following the installation procedure. Refer to
FAX-66, "Removal and Installation"
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JPDIF0293GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст