Nissan Juke F15. Manual — part 1020
PCS-24
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R]
IPDM E/R
IGNITION RELAY MALFUNCTION DETECTION FUNCTION
• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit.
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
FRONT WIPER PROTECTION FUNCTION
IPDM E/R detects front wiper stop position by a front wiper stop position signal.
When a front wiper stop position signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 seconds activation and 20 seconds stop.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
DTC Index
INFOID:0000000012197162
NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now.
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame Data).
- The number is 0 when is detected now.
Front wiper motor
• The status just before activation of fail-safe control is maintained until the ignition switch is turned OFF while
the front wiper is operating at LO or HI speed.
• The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-safe control is activated
while the front wiper is set in the INT mode and the front wiper motor is operating.
• Returns automatically wiper to stop position when ignition switch is turned ON if fail-safe control is activated
while front wiper motor is operated and wiper stop in the other position than stop position.
• The status is held at service position if the fail-safe control is activated while the service position function is
operating.
Front fog lamp
Front fog lamp relay OFF
Daytime running light
Daytime running light relay OFF
Rear window defogger
Rear window defogger relay OFF
Horn
Horn OFF
Ignition relay
The status just before activation of fail-safe is maintained.
Starter motor
Starter control relay OFF
Control part
Fail-safe operation
Voltage judgment
IPDM E/R judgment
Operation
Ignition relay contact
side
Ignition relay excitation
coil side
ON
ON
Ignition relay ON normal
—
OFF
OFF
Ignition relay OFF normal
—
ON
OFF
Ignition relay ON stuck
• Detects DTC “B2098: IGN RELAY ON CIRC”
• Turns ON the tail lamp relay for 10 minutes
OFF
ON
Ignition relay OFF stuck
Detects DTC “B2099: IGN RELAY OFF CIRC”
Ignition switch
Front wiper switch
Front wiper stop position signal
ON
OFF
The front wiper stop position signal (stop position) cannot be input for 10 seconds.
ON
The front wiper stop position signal does not change for 10 seconds.
PCS
IPDM E/R
PCS-25
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
- The number increases like 1
→ 2 ··· 38 → 39 after returning to the normal condition whenever IGN OFF →
ON.
- The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
×: Applicable
CONSULT display
Fail-safe
Refer to
No DTC is detected.
further testing
may be required.
—
—
U1000: CAN COMM CIRCUIT
×
B2098: IGN RELAY ON CIRC
×
B2099: IGN RELAY OFF CIRC
—
B209F: STR CUT OFF OPEN
—
B20A0: STR CUT OFF SHORT
—
B210B: STR CONT RLY ON CIRC
—
B210C: STR CONT RLY OFF CIRC
—
B210D: STARTER RLY ON CIRC
—
B210E: STARTER RLY OFF CIRC
—
B210F: INTRLCK/PNP SW ON
—
B2110: INTRLCK/PNP SW OFF
—
PCS-26
< WIRING DIAGRAM >
[IPDM E/R]
IPDM E/R
WIRING DIAGRAM
IPDM E/R
Wiring Diagram
INFOID:0000000012197163
JRMWI5132GB
PCS
IPDM E/R
PCS-27
< WIRING DIAGRAM >
[IPDM E/R]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JRMWI5133GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст