Nissan Juke F15. Manual — part 90
BR-20
< REMOVAL AND INSTALLATION >
BRAKE PEDAL
REMOVAL AND INSTALLATION
BRAKE PEDAL
Exploded View
INFOID:0000000012200276
Removal and Installation
INFOID:0000000012200277
REMOVAL
1. Remove instrument lower panel. Refer to
IP-13, "Removal and Installation"
2. Disconnect the stop lamp switch and the brake pedal position switch harness connectors.
3. Rotate the stop lamp switch and the brake pedal position switch
(1) counter clockwise to remove.
4. Disconnect the accelerator pedal harness connector and har-
ness clip.
1.
Clevis pin
2.
Brake pedal assembly
3.
Brake pedal pad
4.
Brake pedal position switch
5.
Clip
6.
Stop lamp switch
7.
Snap pin
: Apply multi-purpose grease.
: N·m (kg-m, ft-lb)
JSFIA0457GB
JPFIA0815ZZ
BRAKE PEDAL
BR-21
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
5. Remove snap pin (1) and clevis pin (2) from clevis (3) of brake
booster.
6. Remove the steering member stay (1).
7. Remove the brake pedal assembly.
CAUTION:
Hold the brake booster and master cylinder assembly so as
not to drop out or contact them other parts.
8. Remove accelerator pedal from brake pedal assembly. Refer to
ACC-4, "Removal and Installation"
9. Perform inspection after removal. Refer to
INSTALLATION
Note the following, and install in the reverse order of removal.
• Apply the multi-purpose grease to the clevis pin and the mating faces. (Not necessary if grease has been
already applied)
NOTE:
The clevis pin may be inserted in either direction.
• Perform adjustment after installation. Refer to
BR-21, "Inspection and Adjustment"
.
Inspection and Adjustment
INFOID:0000000012200278
INSPECTION AFTER REMOVAL
• Check for the following items and replace the brake pedal assembly if necessary.
- Check the brake pedal upper rivet (made by aluminum) (A) for
deformation.
- Check the brake pedal for bend, damage, and cracks on the
welded parts.
- Check the lapping length (D) of sub-bracket (B) and slide plate (C).
• Check clevis pin and plastic stopper (A) for damage and deforma-
tion. If any is found, replace clevis pin.
JPFIA0816ZZ
JSFIA0458ZZ
D : 6.5 mm (0.256 in) or more
JSFIA0459ZZ
PFIA0756J
BR-22
< REMOVAL AND INSTALLATION >
BRAKE PEDAL
ADJUSTMENT AFTER INSTALLATION
• Adjust each item of brake pedal after installing the brake pedal assembly to the vehicle. Refer to
.
• Perform the release position learning of the accelerator pedal. Refer to
.
BRAKE PIPING
BR-23
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
BRAKE PIPING
FRONT
FRONT : Exploded View
INFOID:0000000012200279
EXCEPT NISMO RS
NISMO RS
1.
Brake tube
2.
Bracket
3.
Heat insulator
4.
ABS actuator and electric unit (con-
trol unit)
5.
Connector
6.
Master cylinder assembly
7.
Brake booster
8.
Lock plate
9.
Brake hose
10. Union bolt
11. Copper washer
A.
To rear brake tube
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
: Indicates that the part is connected at points with same symbol in actual vehicle.
JSFIA2854GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст