Nissan Juke F15. Manual — part 34
AV-122
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
INSPECTION AND ADJUSTMENT
This mode is designed to align the boundary between each camera image that could not be aligned in the
“Calibrating Camera Image” mode.
CONSULT work support
1. Select “FINE TUNING OF BIRDS-EYE VIEW” by touching CONSULT screen.
2. On the adjustment screen of each camera, adjust the parameter
by touching the “AXIS X” button, “AXIS Y” button”, and
“ROTATE” button to place the calibration marker shown on the
camera screen on the target line drawn on the ground.
NOTE:
Touch “SELECT” button on the CONSULT screen to select the
target camera.
3. Touch “APPLY” button on the CONSULT screen. “PRCSNG” is
displayed and adjustment results are shown on the camera
screen.
CAUTION:
Check that “PRCSNG” is displayed. Do never perform other
operations while “PRCSNG” is displayed.
4. Touch “OK” button on the CONSULT screen. “PRCSNG” is displayed and adjustment results are written to
the around view monitor control unit.
CAUTION:
• Check that “PRCSNG” is displayed. Never perform other operations while “PRCSNG” is dis-
played.
• After pressing the “OK” button, never press buttons other than the “BACK” button.
NOTE:
• It can be initialized to the NISSAN factory default condition with “Initialize Camera Image Calibration”.
• The adjustment value is cancelled in this mode by performing “Initialize Camera Image Calibration”.
>> Calibration end
JSNIA4214ZZ
AV
C1A03 VEHICLE SPEED SENSOR
AV-123
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
DTC/CIRCUIT DIAGNOSIS
C1A03 VEHICLE SPEED SENSOR
DTC Logic
INFOID:0000000012202519
DTC DETECTION LOGIC
NOTE:
If DTC “C1A03” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
"AROUND VIEW MONITOR CONTROL UNIT : DTC Logic"
for DTC “U1000”.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Perform “All DTC Reading” with CONSULT.
3. Check if the “C1A03” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “C1A03” detected as the current malfunction?
YES
>> Refer to
.
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012202520
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A03” in “Self Diagnostic Result” of “AVM”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
AV-128, "AROUND VIEW MONITOR CONTROL UNIT : DTC Logic"
NO
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
NO
>> GO TO 3.
3.
PEPLACE AROUND VIEW MONITOR CONTROL UNIT
1. Replace the around view monitor control unit. Refer to
AV-190, "Removal and Installation"
.
2. Perform DTC confirmation procedure. Refer to
Is “C1A03” detected?
YES
>> Replace the ABS actuator and electric unit (control unit). Refer to
.
NO
>> INSPECTION END
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
C1A03
VHCL SPEED SE CIRC
If the vehicle speed signal (wheel speed) from
ABS actuator and electric unit (control unit) re-
ceived by the around view monitor control unit
via CAN communication, are inconsistent
• ABS actuator and electric unit (control
unit)
• Around view monitor control unit
AV-124
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C1A39 STEERING ANGLE SENSOR
C1A39 STEERING ANGLE SENSOR
DTC Logic
INFOID:0000000012202521
DTC DETECTION LOGIC
NOTE:
If DTC “C1A39” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
"AROUND VIEW MONITOR CONTROL UNIT : DTC Logic"
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the ignition switch ON.
2. Perform “All DTC Reading” with CONSULT.
3. Check if the “C1A39” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “C1A39” detected as the current malfunction?
YES
>> Refer to
.
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012202522
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A39” in “Self Diagnostic Result” of “AVM”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
AV-128, "AROUND VIEW MONITOR CONTROL UNIT : DTC Logic"
NO
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
.
NO
>> GO TO 3.
3.
PEPLACE AROUND VIEW MONITOR CONTROL UNIT
1. Replace the around view monitor control unit. Refer to
AV-190, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
Is “C1A39” detected?
YES
>> Replace the steering angle sensor. Refer to
AV-194, "Removal and Installation"
NO
>> INSPECTION END
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
C1A39
STRG SEN CIR
If the steering angle sensor is malfunction
Steering angle sensor
AV
U0122 ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
AV-125
< DTC/CIRCUIT DIAGNOSIS >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
U0122 ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
DTC Logic
INFOID:0000000012202523
DTC DETECTION LOGIC
NOTE:
If DTC “U0122” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
"AROUND VIEW MONITOR CONTROL UNIT : DTC Logic"
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Perform “All DTC Reading” with CONSULT.
3. Check if the “U0122” is detected as the current malfunction in “Self Diagnostic Result” of “AVM”.
Is “U0122” detected as the current malfunction?
YES
>> Refer to
.
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012202524
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “U0122” in “Self Diagnostic Result” of “AVM”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
AV-128, "AROUND VIEW MONITOR CONTROL UNIT : DTC Logic"
NO
>> GO TO 2.
2.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
NO
>> GO TO 3.
3.
PEPLACE AROUND VIEW MONITOR CONTROL UNIT
1. Replace the around view monitor control unit. Refer to
AV-190, "Removal and Installation"
.
2. Perform DTC confirmation procedure. Refer to
Is “U0122” detected?
YES
>> Replace the ABS actuator and electric unit (control unit). Refer to
.
NO
>> INSPECTION END
DTC
Trouble diagnosis name
DTC detecting condition
Possible causes
U0122
VDC P-RUN DIAGNO-
SIS
If around view monitor control unit detects an
error signal that is received from ABS actuator
and electric unit (control unit) via CAN commu-
nication
ABS actuator and electric unit (control
unit)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст