Nissan Juke F15. Manual — part 774
FRONT DRIVE SHAFT
FAX-35
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
c. Press out support bearing from housing.
d. Remove dust shield from housing.
10. Remove damper bands, then remove dynamic damper from shaft.
ASSEMBLY
Wheel Side
1. Clean the old grease on joint sub-assembly with paper waste.
2. Fill serration slot joint sub-assembly (1) with NISSAN genuine
grease or equivalent until the serration slot and ball groove
become full to the brim.
CAUTION:
After applying grease, use a paper waste to wipe off old
grease that has oozed out.
3. Install boot and boot bands to shaft.
CAUTION:
• Wrap serration on shaft with tape (A) to protect the boot
from damage.
• Never reuse boot and boot band.
4. Remove the tape wrapped around the serration on shaft.
5. Position the circular clip (1) on groove at the shaft edge.
CAUTION:
Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.
YAX004
JPDIF0008ZZ
JPDIF0009ZZ
JPDIF0305ZZ
FAX-36
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DRIVE SHAFT
6. Align both center axles of the shaft edge and joint sub-assembly. Then assemble shaft with joint sub-
assembly holding circular clip.
7. Install joint sub-assembly to shaft using plastic hammer.
CAUTION:
• Check circular clip is properly positioned on groove of the
joint sub-assembly.
• Confirm that joint sub-assembly is correctly engaged
while rotating drive shaft.
8. Apply the specified amount of grease into the boot inside from large diameter side of boot.
9. Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” marks) on the shaft or joint sub-assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
10. To prevent the deformation of the boot, adjust the boot installation length (L) to the specified value shown
below by inserting the suitable tool into inside of the boot from the large diameter side of the boot and dis-
charging the inside air.
CAUTION:
• If the boot installation length exceeds the standard, it may cause breakage of the boot.
• Be careful not to touch the inside of the boot with a tip of tool.
11. Secure the large and small ends of the boot with boot bands
using the boot band crimping tool (A) [SST:KV40107300 ( —
)].
CAUTION:
• Never reuse boot band.
RAC0049D
Grease amount
: Refer to
.
JSDIA2261ZZ
L : Refer to
.
JPDIF0012ZZ
FRONT DRIVE SHAFT
FAX-37
< REMOVAL AND INSTALLATION >
[TYPE 1]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
• Secure boot band so that dimension (M) meets the speci-
fication as shown in the figure.
12. Check that displacement does not occur when boot is rotated with the joint sub-assembly and shaft fixed.
CAUTION:
• Reinstall them using boot bands when boot installation positions become incorrect.
• Never reuse boot band.
Transaxle Side (Left Drive Shaft)
1. Clean the old grease on housing with paper waste.
2. Install dust shield to housing assembly.
CAUTION:
Never reuse dust shield.
3. Install circular clip to housing assembly.
CAUTION:
Never reuse circular clip.
4. Install dynamic damper, follow the procedure described below.
a. Install dynamic damper to shaft.
b. Secure dynamic damper with bands in the following specified
position (A) when installing.
CAUTION:
Never reuse boot bands.
c. Install boot bands securely as showin in the figure.
5. Install boot and boot bands to housing assembly.
CAUTION:
Dimension (M)
: 1.0 – 4.0 mm (0.039 – 0.157 in)
DSF0047D
A :
JPDIF0178ZZ
PDIA1188J
FAX-38
< REMOVAL AND INSTALLATION >
[TYPE 1]
FRONT DRIVE SHAFT
• Wrap serration on housing assembly with tape (A) to pro-
tect the boot from damage.
• Never reuse boot and boot band.
6. Remove the tape wrapped around the serration on shaft.
7. To install the spider assembly (1), align it with the matching
marks (A) on the shaft (2) put during the removal, and direct the
serration mounting surface (B) to the shaft.
8. Secure spider assembly onto shaft with snap ring (1).
CAUTION:
Never reuse snap ring.
9. Apply the appropriate amount of grease to spider assembly and sliding surface.
10. Align matching marks put during the removal of housing assembly.
11. Install stopper ring.
CAUTION:
Never reuse stopper ring.
12. Apply NISSAN genuine grease (refer to parts catalog) to housing assembly.
13. Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (indicated
by “*” marks) on the shaft or housing assembly, boot may
be removed. Remove all grease from the boot mounting
surface.
JPDIF0009ZZ
JPDIF0017ZZ
JPDIF0014ZZ
Grease amount
: Refer to
.
JSDIA2063ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст