Nissan Juke F15. Manual — part 1138
SEC-76
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2604 SHIFT POSITION
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
4.
CHECK BCM INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect transmission range switch connector.
3. Disconnect BCM connector.
4. Check continuity between transmission range switch harness connector and BCM harness connector.
5. Check continuity between transmission range switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK INTERMITTENT INCIDENT
GI-45, "Intermittent Incident"
>> INSPECTION END
Transmission range switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
F27
2
M70
102
Existed
Transmission range switch
Ground
Continuity
Connector
Terminal
F27
2
Not existed
B2605 SHIFT POSITION
SEC-77
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2605 SHIFT POSITION
DTC Logic
INFOID:0000000012202169
DTC DETECTION LOGIC
NOTE:
• If DTC B2605 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2605 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Shift the selector lever to the P position.
2. Turn ignition switch ON and wait 1 second or more.
3. Shift the selector lever to the N position and wait 1 second or more.
4. Shift the selector lever to any position other than P and N, and wait 1 second or more.
5. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012202170
1.
CHECK IPDM E/R INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Disconnect BCM connector.
4. Check continuity between IPDM E/R harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
3. Perform DTC CONFIRMATION PROCEDURE for B2605. Refer to
Is DTC B2605 detected again?
YES
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
.
NO
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2605
PNP/CLUTCH SW
When ignition switch is ON, P/N position
signal input from transmission range switch
and P/N position signal input (CAN) from
IPDM E/R do not match.
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
(Transmission range switch circuit is
open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E15
48
M70
102
Existed
SEC-78
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2608 STARTER RELAY
B2608 STARTER RELAY
DTC Logic
INFOID:0000000012202171
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
.
• If DTC B2608 is displayed with DTC B210D (IPDM E/R), first perform the trouble diagnosis for DTC B210D.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Press push-button ignition switch under the following conditions to start engine.
CVT models
-
Selector lever: In the P position
-
Brake pedal: Depressed
M/T models
-
Shift lever: In the Neutral position
-
Clutch pedal: Depressed
2. Wait 1 second after engine started.
3. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012202172
1.
CHECK DTC OF IPDM E/R
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK STARTER RELAY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Disconnect BCM connector.
4. Check continuity between IPDM E/R harness connector and BCM harness connector.
5. Check continuity between IPDM E/R harness connector and ground.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2608
STARTER RELAY
BCM outputs starter relay OFF signal but
BCM receives starter relay ON signal from
IPDM E/R (CAN).
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
(Starter relay circuit is open or shorted.)
• IPDM E/R
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E13
30
M70
97
Existed
B2608 STARTER RELAY
SEC-79
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
REPLACE IPDM E/R
1. Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
.
2. Perform DTC CONFIRMATION PROCEDURE for DTC B2608. Refer to
Is DTC B2608 detected again?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
>> INSPECTION END
IPDM E/R
Ground
Continuity
Connector
Terminal
E13
30
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст