Nissan Juke F15. Manual — part 1218
TM-62
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
REVERSE IDLER SHAFT AND GEAR
2. Remove snap ring (1).
3. Remove reverse baulk ring (1) and return spring (2).
4. Remove snap ring (1), lock washer (2), and reverse input gear
(3).
5. Remove needle bearings (1) and washer.
Assembly
INFOID:0000000012200789
Note the following procedures, and assemble in the reverse order of disassembly.
CAUTION:
• Never reuse snap ring.
• Check that snap ring is securely installed in a groove.
• Replace reverse output gear, snap ring, reverse baulk ring, return spring, needle bearing, reverse
idler shaft, spacer, reverse input gear, and lock washer as a set.
Inspection
INFOID:0000000012200790
INSPECTION AFTER DISASSEMBLY
PCIB1759E
PCIB1758E
PCIB1757E
PCIB1761E
REVERSE IDLER SHAFT AND GEAR
TM-63
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Shaft and Gear
Check the following items. Replace reverse output gear, snap ring, reverse baulk ring, return spring, needle
bearing, reverse idler shaft, spacer, reverse input gear, and lock washer as a set, if necessary.
• Damage, peeling, bend, uneven wear, and distortion of shaft
• Excessive wear, damage, and peeling of gear
Bearing
Check damage and rotation of bearing. Replace reverse output gear, snap ring, reverse baulk ring, return
spring, needle bearing, reverse idler shaft, spacer, reverse input gear, and lock washer as a set, if necessary.
TM-64
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
FINAL DRIVE
FINAL DRIVE
Exploded View
INFOID:0000000012200791
Disassembly
INFOID:0000000012200792
1. Remove differential side bearing inner race (clutch housing side)
(1), as per the following procedure.
a. Set a puller [Commercial service tool] to differential side bearing
inner race (clutch housing side).
b. Remove differential side bearing inner race (clutch housing
side), using the drift (A) [SST: ST33061000 (J-8107-2)].
1.
Shim
2.
Differential side bearing outer race
(transaxle case side)
3.
Differential side bearing inner race
(transaxle case side)
4.
Final gear
5.
Differential case
6.
Differential side bearing inner race
(clutch housing side)
7.
Differential side bearing outer race
(clutch housing side)
: Replace the parts as a set.
: N·m (kg-m, ft-lb)
JPDIC0424GB
PCIB1767E
FINAL DRIVE
TM-65
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
2. Remove final gear mounting bolts, and then remove final gear
(1).
3. Remove differential side bearing inner race (transaxle case
side) (1), as per the following procedure.
a. Set a puller [Commercial service tool] to differential side bearing
inner race (transaxle case side).
b. Remove differential side bearing inner race (transaxle case
side), using a drift (A) [Commercial service tool].
Assembly
INFOID:0000000012200793
1. Install final gear, and then tighten final gear mounting bolts to the specified torque.
CAUTION:
Replace final gear and differential case as a set.
2. Install differential side bearing inner race (clutch housing side),
using a drift (A) [Commercial service tool].
CAUTION:
Replace differential side bearing inner race (clutch housing
side) and differential side bearing outer race (clutch hous-
ing side) as a set.
3. Install differential side bearing inner race (transaxle case side),
using a drift (A) [Commercial service tool].
CAUTION:
Replace differential side bearing inner race (transaxle case
side) and differential side bearing outer race (transaxle
case side) as a set.
Inspection
INFOID:0000000012200794
INSPECTION AFTER DISASSEMBLY
Gear and Case
Check final gear and differential case. Replace if necessary.
JPDIC0446ZZ
JPDIC0114ZZ
JPDIC0115ZZ
JPDIC0116ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст