Nissan Juke F15. Manual — part 1257
TM-218
< BASIC INSPECTION >
[CVT: RE0F10B]
DIAGNOSIS AND REPAIR WORKFLOW
DIAGNOSTIC WORKSHEET
Symptoms
Vehicle does not move. ( Any position Particular position)
No shift
Lock-up malfunction
Shift shock or slip ( N
→ D N → R Lock-up Any drive position)
Noise or vibration
No pattern select
Others
(
)
Malfunction indicator lamp (MIL)
Continuously lit
Not lit
1
Read the item on cautions concerning fail-safe and understand the customer's complaint.
2
CVT fluid inspection, stall test and line pressure test
CVT fluid inspection
Leak (Repair leak location.)
State
Amount
Stall test
,
Torque converter one-way clutch
Reverse brake
Forward clutch
Steel belt
Engine
Line pressure low
Primary pulley
Secondary pulley
Line pressure inspection - Suspected part:
3
Perform self-diagnosis.
Enter checks for detected items.
4
Perform road test.
4-1.
Check before engine is started
4-2.
Check at idle
4-3.
Cruise test
After completing all rode test, check malfunction phenomena to repair or replace malfunctioning part. Refer to
.
5
Drive vehicle to check that the malfunction phenomenon has been resolved.
6
Erase the results of the self-diagnosis from the TCM and the ECM.
,
ADDITIONAL SERVICE WHEN REPLACING TCM
TM-219
< BASIC INSPECTION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ADDITIONAL SERVICE WHEN REPLACING TCM
Description
INFOID:0000000012200909
When replacing the TCM, perform the following work. For work procedure, refer to
.
TCM PROGRAMMING
• Since vehicle specifications are not yet written in a new TCM, it is necessary to write them with CONSULT.
CAUTION:
When replacing TCM, save TCM data on CONSULT before removing TCM.
LOADING AND STORING OF CALIBRATION DATA
• The TCM acquires calibration data (individual characteristic value) of each solenoid that is stored in the
ROM assembly (in the control valve). This enables the TCM to perform accurate control. After the TCM is
replaced, check that the calibration data is correctly loaded and stored.
CAUTION:
When replacing TCM and transaxle assembly simultaneously, replace transaxle assembly first and
then replace TCM.
Work Procedure
INFOID:0000000012200910
CAUTION:
Immediately after TCM is replaced or after control valve or transaxle assembly is replaced (after TCM
initialization is complete), self-diagnosis result of “P1701”, “P1709” may be displayed. In this case,
erase self-diagnosis result using CONSULT. After erasing self-diagnosis result, perform DTC “P1701”,
“P1709” reproduction procedure and check that malfunction is not detected. Refer to
1.
CHECK NEW TCM PART NUMBER
Check new TCM part number to see whether it is blank TCM or not.
NOTE:
• Part number of blank TCM is 310F6-XXXXX.
• Check the part number when ordering TCM or with the one included in the label on the container box.
Is new TCM a blank TCM?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
SAVE TCM DATA (VEHICLE SPECIFICATIONS)
NOTE:
Save necessary data stored in TCM in CONSULT according to the following instructions:
With CONSULT
1. Turn ignition switch OFF.
2. Connect all of disconnected connectors.
3. Turn ignition switch ON.
4. Select “Re/programming, Configuration”.
5. Select “AT/CVT”.
NOTE:
If “AT/CVT” is not displayed and TCM data cannot be saved on CONSULT, GO TO 3.
6. Select “Programming”.
7. Save TCM data on CONSULT according to the CONSULT display.
>> GO TO 3.
3.
REPLACE THE TCM
1. Turn ignition switch OFF and wait for 10 seconds.
TM-328, "Removal and Installation"
>> GO TO 4.
4.
LOAD CALIBRATION DATA
TM-220
< BASIC INSPECTION >
[CVT: RE0F10B]
ADDITIONAL SERVICE WHEN REPLACING TCM
1. Shift the selector lever to the “P” position.
2. Turn ignition switch ON.
3. Check that “P” is displayed on shift position indicator on combination meter.
NOTE:
Displayed approximately 1 – 2 seconds after the selector lever is moved to the “P” position.
Does the shift position indicator display “P”?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
DETECT MALFUNCTIONING ITEM
Check the following items:
• Harness between the TCM and the ROM assembly inside the transaxle assembly is open or shorted.
• Disconnected, loose, bent, collapsed, or otherwise abnormal connector housing terminals
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
6.
STORE CALIBRATION DATA
1. Turn ignition switch OFF and wait for 5 seconds.
2. Turn ignition switch ON.
CAUTION:
Never start the engine.
Does the shift position indicator display “P” at the same time when turning ON the ignition switch?
YES -1 (TCM is blank)>>GO TO 7.
YES -2 (TCM is not blank)>>WORK END
NO
>> Check harness between battery and TCM harness connector terminal. Refer to
7.
WRITE TCM DATA (VEHICLE SPECIFICATIONS)
NOTE:
Write data saved in CONSULT into a new TCM according to the following instructions:
With CONSULT
1. Select “Programming”.
2. Perform programming according to the CONSULT display.
>> WORK END
ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE OR TRANSAXLE
ASSEMBLY
TM-221
< BASIC INSPECTION >
[CVT: RE0F10B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE OR TRAN-
SAXLE ASSEMBLY
Description
INFOID:0000000012200911
When replacing the transaxle assembly/control valve, perform the following work. For work procedure, refer to
.
ERASING, LOADING AND STORING OF CALIBRATION DATA
• The TCM acquires calibration data (individual characteristic value) of each solenoid that is stored in the
ROM assembly (in the control valve). This enables the TCM to perform accurate control. For this reason,
after the transaxle assembly/control valve is replaced, it is necessary to erase the calibration data previously
stored in TCM, to load new calibration data, and to store them.
ERASING OF CVT FLUID DEGRADATION LEVEL DATA
• TCM records the degradation level of the CVT fluid calculated from the vehicle driving status. Therefore, if
the transaxle assembly/control valve is replaced, it is necessary to erase the CVT fluid degradation level
data recorded by TCM.
Work Procedure
INFOID:0000000012200912
CAUTION:
Immediately after TCM is replaced or after control valve or transaxle assembly is replaced (after TCM
initialization is complete), self-diagnosis result of “P1701”, “P1709” may be displayed. In this case,
erase self-diagnosis result using CONSULT. After erasing self-diagnosis result, perform DTC “P1701”,
“P1709” reproduction procedure and check that malfunction is not detected. Refer to
1.
PREPARATION BEFORE WORK
With CONSULT
1. Start the engine.
CAUTION:
Never drive the vehicle.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “ATFTEMP COUNT”.
Is “ATFTEMP COUNT” 47 [equivalent to 20
°C (68°F)] or more?
YES
>> GO TO 2.
NO
>> 1. Warm up the transaxle assembly until “ATFTEMP COUNT” reaches “47” [equivalent to 20
°C
(68
°F)] or more.
2. GO TO 2.
2.
PERFORM TCM INITIALIZATION
With CONSULT
1. Turn ignition switch OFF.
2. Turn ignition switch ON.
CAUTION:
Never start the engine.
3. Select “Self Diagnostic Results” in “TRANSMISSION”.
4. Shift selector lever to “R” position.
5. Depress slightly the accelerator pedal (Pedal angle: 2.0/8) while depressing the brake pedal.
6. Select “Erase” with step 5.
7. Release brake pedal and accelerator pedal.
8. Select “CALIB DATA” in “TRANSMISSION”.
9. Check that “CALIB DATA” value is as shown as in the following table.
Item name
Display value
UNIT CLB ID 1
00
UNIT CLB ID 2
00
UNIT CLB ID 3
00
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст