Nissan Juke F15. Manual — part 756
FRONT BUMPER
EXT-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
NISMO RS
19. Bumper side bracket LH
20. Screw grommet
21. Double-sided tape
[t: 1.2 mm (0.047 in)]
22. U nut
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
, , , , , : Indicates that the part is connected at points with same symbol in actual vehicle.
EXT-16
< REMOVAL AND INSTALLATION >
FRONT BUMPER
1.
Front upper grille
2.
Bumper side bracket RH
3.
Bumper reinforcement
4.
Front grille
5.
Emblem
6.
Bumper energy absorber
7.
Bumper end rubber RH
8.
Bumper fascia
9.
Screw grommet
10. Bumper bracket cover
11. License plate bracket
12. Bumper fascia lower
13. Daytime running light RH
14. Daytime running light LH
15. Front bumper finisher
16. Front bumper grille
17. Bumper end rubber LH
18. Bumper retainer lower
JMKIB4701GB
FRONT BUMPER
EXT-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
Removal and Installation
INFOID:0000000012199311
CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.
REMOVAL
1. Fully open hood assembly.
2. Remove fixing clips (A) of bumper upper side.
3. Remove front fillet molding front side. Refer to
EXT-36, "FRONT FILLET MOLDING : Removal and Instal-
.
4. Remove bumper fascia fixing screws (A) (LH and RH).
5. Remove air guide mounting bolts, and then remove air guide (LH and RH). Refer to
.
6. Remove fixing clips of bumper lower side. (except for NISMO and NISMO RS)
7. Remove fixing screws of bumper lower side. (NISMO and NISMO RS)
8. Pull bumper fascia side toward the vehicle side to disengage the fitting of bumper side bracket and
bumper fascia side according to the numerical order 1
→3 as shown by the arrows in the figure.
19. Bumper side bracket LH
20. Screw grommet
21. Double-sided tape
[t: 1.2 mm (0.047 in)]
22. U nut
: Pawl
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
, , , , , : Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIA5593ZZ
JMKIA5559ZZ
EXT-18
< REMOVAL AND INSTALLATION >
FRONT BUMPER
• Except for NISMO and NISMO RS
CAUTION:
When removing bumper fascia assembly, 2 workers are
required so as to prevent it from dropping.
• NISMO and NISMO RS
CAUTION:
When removing bumper fascia assembly, 2 workers are
required so as to prevent it from dropping.
9. Disconnect front fog lamp harness connectors. (with front fog lamp)
10. Disconnect daytime running light harness connectors. (with daytime running light)
11. Remove bumper fascia assembly.
12. Remove the following parts after removing bumper fascia assembly.
• Daytime running light (LH and RH). Refer to
EXL-101, "Removal and Installation"
. (with daytime running
light)
• Front fog lamp (LH and RH). Refer to
EXL-102, "Removal and Installation"
. (with front fog lamp)
• Bumper finisher (LH and RH). (without front fog lamp)
• Front grille. Refer to
EXT-26, "Removal and Installation"
• Bumper fascia lower.
• Bumper end rubber (LH and RH).
• Bumper bracket cover.
• License plate bracket.
• Front bumper finisher. (NISMO and NISMO RS)
• Front bumper grille. (NISMO and NISMO RS)
13. Remove bumper energy absorber.
14. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement.
15. Remove bumper retainer lower fixing clips, and then remove bumper retainer lower.
16. Remove bumper side bracket fixing screws, and then remove bumper side bracket.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
NOTE:
• The following table shows the specified values for checking normal installation status.
• Fitting adjustment cannot be performed.
: Pawl
JMKIA5592ZZ
: Pawl
JMKIB4684ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст