Nissan Juke F15. Manual — part 708
EXL-52
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
HEADLAMP (HI) CIRCUIT
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace harness.
9.
CHECK DAYTIME RUNNING LIGHT RELAY
Check daytime running light relay. Refer to
EXL-52, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace daytime running light relay.
10.
CHECK HEADLAMP (HI) RH BULB
Check the headlamp (HI) RH bulb.
Is the inspection result normal?
YES
>> Check the headlamp (HI) RH harness. Repair or replace if necessary.
NO
>> Replace headlamp (HI) RH bulb. Refer to
.
11.
CHECK HEADLAMP (HI) LH GROUND CIRCUIT
Check continuity between headlamp harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 12.
NO
>> Repair or replace harness.
12.
CHECK HEADLAMP (HI) LH BULB
Check the headlamp (HI) LH bulb.
Is the inspection result normal?
YES
>> Check the headlamp (HI) LH harness. Repair or replace if necessary.
NO
>> Replace headlamp (HI) LH bulb. Refer to
Component Inspection
INFOID:0000000012201638
1.
CHECK DAYTIME RUNNING LIGHT RELAY
1. Turn ignition switch OFF.
2. Remove daytime running light relay.
3. Apply battery voltage to daytime running light relay between terminals 2 and 1.
4. Check continuity of daytime running light relay terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace daytime running light relay.
Daytime running light relay
—
Continuity
Connector
Terminal
E65
4
Ground
Existed
Headlamp
—
Continuity
Connector
Terminal
E54
3
Ground
Existed
Daytime running light relay
Condition
Continuity
Terminal
3
4
Battery voltage
Apply
Not existed
Not apply
Existed
HEADLAMP (LO) CIRCUIT
EXL-53
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HEADLAMP (LO) CIRCUIT
Component Function Check
INFOID:0000000012201639
1.
CHECK HEADLAMP (LO) OPERATION
With CONSULT
1. Turn ignition switch ON.
2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.
3. With operating the test items, check that the headlamp (LO) is turned ON.
Without CONSULT
1. Start IPDM E/R auto active test. Refer to
PCS-12, "Diagnosis Description"
2. Check that the headlamp (LO) is turned ON.
Is the inspection result normal?
YES
>> Headlamp (LO) circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012201640
1.
CHECK HEADLAMP (LO) FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not blown (open).
Is the fuse blown (open)?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown (open).
NO
>> GO TO 2.
2.
CHECK HEADLAMP (LO) POWER SUPPLY
With CONSULT
1. Turn ignition switch ON.
2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.
3. With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
.
3.
CHECK HEADLAMP (LO) POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and headlamp connector.
3. Check continuity between IPDM E/R harness connector and headlamp harness connector.
Lo
: Headlamp (LO) ON
Off
: Headlamp (LO) OFF
Unit
Location
Fuse No.
Capacity
Headlamp LO (RH)
IPDM E/R
#54
15 A
Headlamp LO (LH)
#53
+
-
Test item
Voltage
IPDM E/R
Connector
Terminal
RH
E15
52
Ground
EXTERNAL
LAMPS
LO
9 – 16 V
Off
0 – 1 V
LH
51
LO
9 – 16 V
Off
0 – 1 V
EXL-54
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
HEADLAMP (LO) CIRCUIT
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK HEADLAMP (LO) GROUND CIRCUIT
Check continuity between headlamp harness connector and ground.
Is the inspection result normal?
YES
>> Perform the xenon headlamp diagnosis. Refer to
.
NO
>> Repair or replace harness.
IPDM E/R
Headlamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E15
52
E55
4
Existed
LH
51
E54
Headlamp
—
Continuity
Connector
Terminal
RH
E55
2
Ground
Existed
LH
E54
XENON HEADLAMP
EXL-55
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
XENON HEADLAMP
Diagnosis Procedure
INFOID:0000000012201641
1.
CHECK XENON BULB
Install the normal bulb to the applicable headlamp. Check that the headlamp (LO) is turned ON.
Is the headlamp (LO) turned ON?
YES
>> Replace the corresponding xenon bulb. Refer to
NO
>> GO TO 2.
2.
CHECK XENON HEADLAMP
Install the normal headlamp assembly to the applicable headlamp. Check that the headlamp (LO) is turned
ON.
Is the headlamp (LO) turned ON?
YES
>> Replace the corresponding headlamp assembly. Refer to
EXL-96, "Removal and Installation"
NO
>> Xenon headlamp is normal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст