Nissan Juke F15. Manual — part 262

P181E STEERING ANGLE SENSOR

DLN-53

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

P181E STEERING ANGLE SENSOR

DTC Logic

INFOID:0000000012199393

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Turn the ignition switch OFF to ON.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181E” detected?

YES

>> Proceed to

DLN-53, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199394

1.

PERFORM ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ABS”.
Is DTC “C1143” detected?

YES

>> Proceed to

BRC-108, "Diagnosis Procedure"

.

NO

>> GO TO 2.

2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P181E”

is detected, Replace AWD control module. Refer to

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P181E

STR ANGLE SEN

Malfunction is detected in steering angle
sensor signal through CAN communica-
tion.

• Steering angle sensor
- Steering angle sensor error
- Malfunction of steering angle sensor

circuit

• Malfunction of AWD control module
• CAN communication line

DLN-54

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P181F INCOMPLETE CALIBRATION

P181F INCOMPLETE CALIBRATION

DTC Logic

INFOID:0000000012199395

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Turn the ignition switch OFF to ON.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P181F” detected?

YES

>> Proceed to

DLN-54, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199396

1.

PERFORM WRITING UNIT CHARACTERISTICS

1. Erase self-diagnostic result for “ALL MODE AWD/4WD”.

2. Perform writing unit characteristics. Refer to

DLN-42, "Work Procedure"

.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC except “P181F” detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to

DLN-31, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS AGAIN

With CONSULT

Perform “DTC CONFIRMATION PROCEDURE” (self-diagnosis) again. Refer to

DLN-54, "DTC Logic"

.

Is DTC “P181F” detected?

YES

>> Replace AWD control module. Refer to

DLN-91, "Removal and Installation"

.

NO

>> Check AWD control module pin terminals for damage or loose connection with harness connector.

If any items are damaged, repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P181F

INCOMP CALIBRATION

When incomplete writing unit character-
istics of rear final drive is detected.

Writing unit characteristics is incom-
plete.

P1820 ENGINE SPEED SIGNAL

DLN-55

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

P1820 ENGINE SPEED SIGNAL

DTC Logic

INFOID:0000000012199397

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1820” detected?

YES

>> Proceed to

DLN-55, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199398

1.

PERFORM ECM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ENGINE”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to

EC-706, "DTC Index"

(Except for NISMO

RS),

EC-115, "DTC Index"

(For NISMO RS).

NO

>> GO TO 2.

2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1820”

is detected, Replace AWD control module. Refer to

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P1820

ENGINE SPEED SIG

Malfunction is detected in engine speed
signal that is output from ECM through
CAN communication.

• ECM
• AWD control module
• CAN communication line

DLN-56

< DTC/CIRCUIT DIAGNOSIS >

[TRANSFER: TY21B]

P1829 ACCELERATOR PEDAL POSITION SENSOR

P1829 ACCELERATOR PEDAL POSITION SENSOR

DTC Logic

INFOID:0000000012199399

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and

wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION

With CONSULT

1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.

2. Stop the vehicle.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is DTC “P1829” detected?

YES

>> Proceed to

DLN-56, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000012199400

1.

PERFORM ECM SELF-DIAGNOSIS

With CONSULT

Perform self-diagnosis for “ENGINE”.
Is any DTC detected?

YES

>> Perform trouble diagnosis for detected DTC. Refer to

EC-706, "DTC Index"

(Except for NISMO

RS),

EC-115, "DTC Index"

(For NISMO RS).

NO

>> GO TO 2.

2.

CHECK TERMINALS AND HARNESS CONNECTORS

Check AWD control module pin terminals for damage or loose connection with harness connector.
Is inspection result normal?

YES

>> After turning the ignition switch OFF, perform DTC confirmation procedure again. If DTC “P1829”

is detected, Replace AWD control module. Refer to

DLN-91, "Removal and Installation"

.

NO

>> Repair or replace error-detected parts.

DTC

Display item

Malfunction detected condition

Possible cause

P1829

THROTTLE POSI SEN

Malfunction is detected in accelerator
pedal position signal that is output from
ECM through CAN communication.

• ECM
• AWD control module
• CAN communication line

Была ли эта страница вам полезна?
Да!Нет
2 посетителя считают эту страницу полезной.
Большое спасибо!
Ваше мнение очень важно для нас.

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.

Текст

Политика конфиденциальности