Nissan Juke F15. Manual — part 241
DLK-144
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
• Check door hinge rotating part for poor lubrication. If neces-
sary, apply body grease.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000012196721
REMOVAL
1. Fully close the rear door window.
2. Remove rear door finisher. Refer to
INT-16, "Removal and Installation"
.
3. Remove mounting bolts of rear door speaker, and then remove rear door speaker.
4. Disconnect harness connector of rear door speaker.
5. Remove mounting bolt of the check link on the vehicle.
6. Remove mounting bolts of the check link on door panel.
7. Take door check link (1) out from the hole of door panel (2).
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check rear door open/close operation after installation.
• Check door check link rotating part for poor lubrication. If
necessary, apply grease.
: Grease up point
JMKIA5641ZZ
JMKIA5879ZZ
: Grease up point
JMKIA5642ZZ
BACK DOOR
DLK-145
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
Exploded View
INFOID:0000000012196722
REMOVAL
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000012196723
CAUTION:
• Operate with two workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
REMOVAL
1. Remove luggage side upper finisher (LH and RH). Refer to
INT-36, "LUGGAGE SIDE UPPER FINISHER
1.
Back door weather-strip
2.
Back door stay
3.
Back door stay lower bracket
4.
Bumper rubber
5.
Back door striker
6.
Back door panel
7.
Back door hinge
8.
Hole cover
A
: Center mark
B
: Seam
: Always replace after every disassembly.
: Body grease
: Indicates that the part is connected at points with same symbol in actual vehicle.
JMKIA5652ZZ
DLK-146
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR
2. Disconnect harness connector.
3. Remove rear washer hose (1) from hose mounting clip (A), and
then disengage hose.
4. Remove center pillar upper garnish. Refer to
INT-22, "CENTER PILLAR UPPER GARNISH : Removal
5. Remove upper side of back door weather-strip. Refer to
DLK-152, "BACK DOOR WEATHER-STRIP :
.
6. Remove rear assist grip (LH and RH) and mounting clips for rear portion of headlining, and then remove
rear portion of headlining. Refer to
INT-27, "NORMAL ROOF : Exploded View"
.
7. Remove ground harness mounting bolt (A) and harness fixing
clips (B).
8. Remove grommet (1), and then pull out harness from roof panel
(2).
: Vehicle front
JMKIA5653ZZ
: Vehicle front
JMKIA5654ZZ
: Vehicle front
JMKIA5655ZZ
JMKIA5657ZZ
BACK DOOR
DLK-147
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
9. Remove grommet (2), and then pull out harness and washer
tube from roof panel (1).
10. Support back door with the proper material to prevent it from falling.
WARNING:
Bodily injury may occur if no supporting rod is holding the back door open when removing the
back door stay.
11. Remove back door stay (back door side). Refer to
DLK-151, "BACK DOOR STAY : Removal and Installa-
12. Remove back door hinge mounting nuts on back door and remove back door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check back door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, check back door open/close, lock/unlock operation.
• After installation, perform the fitting adjustment. Refer to
DLK-148, "BACK DOOR ASSEMBLY :
JMKIA5658ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст