Nissan Juke F15. Manual — part 269
AWD MODE INDICATOR LAMP (AWD)
DLN-81
< DTC/CIRCUIT DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD MODE INDICATOR LAMP (AWD)
Component Function Check
INFOID:0000000012199440
1.
AWD MODE INDICATOR LAMP OPERATION CHECK
Check that AWD mode indicator lamp (AWD) turns on for approximately 1 second after the ignition switch is
turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000012199441
1.
CHECK AWD WARNING LAMP
1. Start the engine and drive at 30 km/h (19 MPH) or more for approximately 1 minute.
2. Stop the vehicle.
Does AWD warning lamp turn ON?
YES
>> Proceed to
.
NO
>> GO TO 2.
2.
CHECK AWD MODE SWITCH
Perform the trouble diagnosis for AWD mode switch. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK AWD MODE INDICATOR LAMP SIGNAL
With CONSULT
1. Start the engine.
CAUTION:
Stop the vehicle.
2. Change AWD mode switch to “AWD” from “AWD-V”.
3. Check “INDICATOR” in “DATA MONITOR” for “ALL MODE AWD/4WD”.
Does the item on “DATA MONITOR” indicate “AWD”?
YES
>> GO TO 4.
NO
>> Replace AWD control module. Refer to
DLN-91, "Removal and Installation"
.
4.
CHECK COMBINATION METER POWER SUPPLY CIRCUIT
Perform the trouble diagnosis for combination meter power supply circuit. Refer to
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace the error-detected parts.
DLN-82
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
AWD WARNING LAMP DOES NOT TURN ON
SYMPTOM DIAGNOSIS
AWD WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000012199442
AWD warning lamp does not turn ON when the ignition switch is turned to ON.
Diagnosis Procedure
INFOID:0000000012199443
1.
CHECK AWD WARNING LAMP
Perform the trouble diagnosis for AWD warning lamp. Refer to
Is the inspection result normal?
YES
>> Check each harness connector pin terminal for malfunction or disconnection.
NO
>> Repair or replace the error-detected parts.
AWD WARNING LAMP DOES NOT TURN OFF
DLN-83
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000012199444
AWD warning lamp does not turn OFF approx. 1 second after the engine started.
Diagnosis Procedure
INFOID:0000000012199445
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK AWD WARNING LAMP
Perform the trouble diagnosis of the AWD warning lamp. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the error-detected parts.
3.
CHECK AWD CONTROL MODULE POWER SUPPLY AND GRAND CIRCUIT
Perform the trouble diagnosis of power supply and ground circuit. Refer to
.
Is the inspection result normal?
YES
>> Check each harness connector pin terminal for malfunction or disconnection.
NO
>> Repair or replace the error-detected parts.
DLN-84
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS
HEAVY TIGHT-CORNER BRAKING SYMPTOM OCCURS
Description
INFOID:0000000012199446
Heavy tight-corner braking symptom occurs when the vehicle is driven and the steering wheel is turned fully to
either side after the engine is started.
NOTE:
Light tight-corner braking symptom may occur depending on driving conditions. This is not malfunction.
Diagnosis Procedure
INFOID:0000000012199447
1.
PERFORM ECM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
(Except for NISMO
(For NISMO RS).
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is any DTC detected?
YES
>> Perform trouble diagnosis for detected DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK AWD SOLENOID
Perform the trouble diagnosis of the AWD solenoid. Refer to
(Right side).
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the error-detected parts.
4.
CHECK ELECTRIC CONTROLLED COUPLING
1. Turn the ignition switch OFF.
2. Set the transaxle to neutral. Release the parking brake.
3. Lift up the vehicle.
4. Rotate the propeller shaft by hand.
5. Hold rear wheel of right and left lightly.
Does rear wheel rotate?
YES
>> Replace electric controlled coupling for mechanical malfunction (clutch sticking etc.). Refer to
DLN-145, "Removal and Installation"
NO
>> Check each harness connector pin terminal for disconnection.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст