Nissan Juke F15. Manual — part 963
LAN
MAIN LINE BETWEEN IPDM-E AND HVAC CIRCUIT
LAN-189
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 9)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DTC/CIRCUIT DIAGNOSIS
MAIN LINE BETWEEN IPDM-E AND HVAC CIRCUIT
Diagnosis Procedure
INFOID:0000000012200654
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector E105
-
Harness connector M77
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect the following harness connectors.
-
IPDM E/R
-
Harness connectors E105 and M77
2. Check the continuity between the IPDM E/R harness connector and the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the IPDM E/R and the harness connector E105.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect the connector of A/C amp.
2. Check the continuity between the harness connector and the A/C auto amp. harness connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the IPDM E/R and the A/C auto amp.
NO
>> Repair the main line between the harness connector M77 and the A/C auto amp.
IPDM E/R harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E13
27
E105
1
Existed
26
6
Existed
Harness connector
A/C auto amp. harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M77
1
M50
6
Existed
6
7
Existed
LAN-190
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 9)]
MAIN LINE BETWEEN HVAC AND DLC CIRCUIT
MAIN LINE BETWEEN HVAC AND DLC CIRCUIT
Diagnosis Procedure
INFOID:0000000012200655
1.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect the following harness connectors.
-
ECM
-
A/C auto amp.
4. Check the continuity between the A/C auto amp. harness connector and the data link connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the A/C auto amp. and the data link connec-
tor.
NO
>> Repair the main line between the A/C auto amp. and the data link connector.
A/C auto amp. harness connector
Data link connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M50
6
M4
6
Existed
7
14
Existed
LAN
ECM BRANCH LINE CIRCUIT
LAN-191
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 9)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ECM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200656
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the ECM for damage, bend and loose connection (unit side and
connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of ECM.
2. Check the resistance between the ECM harness connector terminals.
-
For NISMO RS models
-
Except for NISMO RS models
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the ECM branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the ECM. Refer to the following.
• For NISMO RS models:
• Except for NISMO RS models:
Is the inspection result normal?
YES (Present error)>>Replace the ECM. Refer to the following.
• For NISMO RS models:
EC-590, "Removal and Installation"
• Except for NISMO RS models:
EC-1256, "Removal and Installation"
YES (Past error)>>Error was detected in the ECM branch line.
NO
>> Repair the power supply and the ground circuit.
ECM harness connector
Resistance (
Ω)
Connector No.
Terminal No.
E18
100
99
Approx. 108 – 132
ECM harness connector
Resistance (
Ω)
Connector No.
Terminal No.
E19
124
123
Approx. 108 – 132
LAN-192
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 9)]
4WD BRANCH LINE CIRCUIT
4WD BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200657
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
AWD control module
-
Harness connector B7
-
Harness connector E107
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of AWD control module.
2. Check the resistance between the AWD control module harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the AWD control module branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the AWD control module. Refer to
Is the inspection result normal?
YES (Present error)>>Replace the AWD control module. Refer to
DLN-91, "Removal and Installation"
.
YES (Past error)>>Error was detected in the AWD control module branch line.
NO
>> Repair the power supply and the ground circuit.
AWD control module harness connector
Resistance (
Ω)
Connector No.
Terminal No.
B47
4
5
Approx. 54 – 66
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст