Nissan Juke F15. Manual — part 236
DLK-124
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
REMOVAL AND INSTALLATION
HOOD
Exploded View
INFOID:0000000012196700
HOOD ASSEMBLY
HOOD ASSEMBLY : Removal and Installation
INFOID:0000000012196701
CAUTION:
• Operate with two workers, because of its heavy weight.
• Use protective tape or shop cloth to protect from damage during removal and installation.
REMOVAL
1. Support hood assembly with the proper material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported by the proper material when removing hood
assembly.
2. Remove hood hinge mounting nuts on the hood to remove the hood assembly.
1.
Hood assembly
2.
Hood bumper rubber
3.
Radiator core seal
4.
Hood insulator
5.
Hood bumper rubber
6.
Grommet
7.
Clamp
8.
Hood support rod
9.
Hood hinge
: Clip
: Pawl
: Body grease
JMKIA6518ZZ
HOOD
DLK-125
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the heads of hood hinge mounting bolts
and nuts.
• After installing, perform hood fitting adjustment. Refer to
DLK-125, "HOOD ASSEMBLY : Adjust-
HOOD ASSEMBLY : Adjustment
INFOID:0000000012196702
Check the clearance and the surface height between hood and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
1.
Hood assembly
2.
Hood bumper rubber
3.
Hood hinge
4.
Hood lock assembly
5.
Front bumper fascia
6.
Front combination lamp
7.
Front fender
: N·m (kg-m, ft-lb)
: Body grease
JMKIA5626GB
DLK-126
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
HOOD
Unit: mm (in)
FITTING ADJUSTMENT PROCEDURE
1. Remove front center grille. Refer to
EXT-26, "Removal and Installation"
2. Remove hood lock assembly, and then adjust the surface height of hood assembly, front fender assembly,
and front combination lamp according to the specified value, by rotating hood bumper rubber.
3. Position hood lock assembly and engage hood striker. Check hood lock assembly and hood striker for
looseness.
4. Move hood lock assembly laterally until the center of hood striker and hood lock assembly are vertical
when viewed from the front.
5. After adjustment, tighten lock bolts to the specified torque.
6. Open hood. Rotate bumper rubber counterclockwise between half a turn and three-quarters of a turn.
7. Check that secondary latch is securely engaged with secondary hood striker from the dead load of the
hood assembly.
8. Check that primary latch is securely engaged with primary hood striker when hood assembly is closed
[free-fall from approximately 200 mm (7.874 in) height].
CAUTION:
Never free-fall hood assembly from a height of 300 (11.811 in) mm or more.
9. Install front center grille. Refer to
EXT-26, "Removal and Installation"
HOOD HINGE
HOOD HINGE : Removal and Installation
INFOID:0000000012196703
REMOVAL
1. Remove hood assembly. Refer to
DLK-124, "HOOD ASSEMBLY : Removal and Installation"
2. Remove front fender. Refer to
DLK-133, "Removal and Installation"
3. Remove hood hinge mounting bolts, and then remove hood hinge.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• After installation, perform hood hinge fitting adjustment. Refer to
DLK-127, "HOOD HINGE : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of the hinge mounting bolts
and nuts.
Portion
Standard
Difference
(RH/LH,
MAX)
Hood – Front
bumper fascia
A – A
E
Clearance
2.0 – 6.0 (0.079 – 0.236)
< 2.5 (0.098)
F Surface height
(-2.0) – (+2.0) [(-0.079) – (+0.079)]
< 2.5 (0.098)
Hood – Front combi-
nation lamp
B – B G
Clearance
2.0 – 6.0 (0.079 – 0.236)
< 2.5 (0.098)
Hood – Front combi-
nation lamp
C – C H
Clearance
2.0 – 6.0 (0.079 – 0.236)
< 2.5 (0.098)
Hood – Front fender
D – D
I
Clearance
2.5 – 4.5 (0.098 – 0.177)
< 1.5 (0.059)
J Surface height
(-2.0) – (0.0) [(-0.079) – (0.000)]
< 1.5 (0.059)
HOOD
DLK-127
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
• Check hood hinge rotating part for poor lubrication. If neces-
sary, apply grease.
HOOD HINGE : Adjustment
INFOID:0000000012196704
Check the clearance and the surface height between hood and each part by visually and touching.
JMKIA5721ZZ
1.
Hood assembly
2.
Hood bumper rubber
3.
Hood hinge
4.
Hood lock assembly
5.
Front bumper fascia
6.
Front combination lamp
7.
Front fender
: N·m (kg-m, ft-lb)
: Body grease
JMKIA5626GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст