Nissan Primera P12. Manual — part 696
SC-30
STARTING SYSTEM
●
Less than 0.2 mm (0.008 in) ... Undercut to 0.5 to 0.8 mm (0.020 to 0.031 in)
Assembly
EKS009LF
Apply high-temperature grease to lubricate the bearing, gears and frictional surface when assembling the
starter.
Carefully observe the following instructions.
PINION PROTRUSION LENGTH ADJUSTMENT
Movement (YD Engine Models)
Compare movement “ ” in height of pinion when it is pushed out
with magnetic switch energized and when it is pulled out by hand
until it touches stopper.
●
Not in the specified value...Adjust by adjusting plate.
SEL022Z
Movement “ ”
: Refer to SDS.
.
MEL140L
SEL633BA
STARTING SYSTEM
SC-31
C
D
E
F
G
H
I
J
L
M
A
B
SC
Clearance (F9Q Engine Models)
With pinion driven out by magnetic switch, push pinion back to
remove slack and measure clearance “ ” between the front edge of
the pinion and the pinion stopper.
●
Not in the specified value ... Adjust by adjusting plate.
Clearance “ ”
: Refer to SDS.
.
SEL026Z
SEL633BA
SC-32
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Battery
EKS009LG
Starter
EKS009LH
Alternator
EKS009LI
Applied model
YD engine
F9Q engine
Type
LB3 (010S)
Capacity V-AH
12-56
Type
M8T71471
D7R 49
MITSUBISHI
Valeo
Reduction
Non-reduction
Applied model
YD engine
F9Q engine
System voltage V
12
No-load
Terminal voltage V
11.0
Current A
Less than 145
Revolution rpm
More than 3,300
11,500
Minimum diameter of commutator mm (in)
31.4 (1.236)
Minimum length of brush mm (in)
11.0 (0.433)
Brush spring tension N (kg, lb)
26.7 - 36.1 (2.7 - 3.7, 6.0 - 8.2)
Clearance between bearing metal and armature
shaft mm (in)
—
Clearance “
” between pinion front edge and pin-
ion stopper mm (in)
—
Movement “
” in height of pinion assembly
mm (in)
0.5 - 2.0 (0.020 - 0.079)
Type
A3TA6581A
MITSUBISHI
Valeo
Applied model
YD engine
F9Q engine
Nominal rating V-A
12-110
Ground polarity
Negative
Minimum revolutions under no-load (When 13.5V
is applied) rpm
Less than 1,300
Hot output current (When 13.5V is applied) A/rpm
More than 29/1,300
More than 78/2,500
More than 102/5,000
Regulated output voltage V
14.1 - 14.7
Minimum length of brush mm (in)
More than 5.0 (0.197)
Brush spring pressure N (g, oz)
4.8 - 6.0 (490 - 610, 17.28 - 21.51)
Slip ring minimum diameter mm (in)
More than 22.1 (0.870)
Rotor coil resistance at 20
°
C (68
°
F)
Ω
1.8 - 2.1
WT-1
ROAD WHEELS & TYRES
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION
A
B
WT
ROAD WHEELS & TYRES
PRECAUTIONS . . . . . . . . . . . . . . .. 2
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 3
NVH Troubleshooting Chart . . . . . . . . . . 3
ROAD WHEEL . . . . . . . . . . . . . . . 4
Inspection . . . . . . . . . . . . . . . . . 4
ALUMINUM WHEEL . . . . . . . . . . . . 4
STEEL WHEEL . . . . . . . . . . . . . . 4
ROAD WHEEL AND TYRE ASSEMBLY . . . . . 5
Balancing Wheels (Bonding Weight Type) . . . ... 5
REMOVAL . . . . . . . . . . . . . . . . 5
WHEEL BALANCE ADJUSTMENT . . . . . .. 5
Balancing Wheels (Drive-in Weight Type) . . . . 6
WHEEL BALANCE ADJUSTMENT . . . . . .. 6
Rotation . . . . . . . . . . . . . . . . . 7
TYRE PRESSURE MONITORING SYSTEM . . . .. 8
System Components . . . . . . . . . . . . 8
System Description . . . . . . . . . . . . .. 8
TYRE PRESSURE MONITORING SENSOR . ... 8
TYRE PRESSURE MONITORING ANTENNA
(RECEIVER) . . . . . . . . . . . . . . . 8
TYRE PRESSURE WARNING CONTROL UNIT. . 9
DISPLAY . . . . . . . . . . . . . . . ... 9
CAN COMMUNICATION . . . . . . . . . . ...11
System Description . . . . . . . . . . . . .11
CAN Communication Unit . . . . . . . . . ...11
TYPE 21,TYPE22/TYPE29, TYPE30 . . . . .. 12
TYPE 23,TYPE24/TYPE31, TYPE32 . . . . .. 13
TYPE 25/TYPE26 . . . . . . . . . . . ... 14
TYPE 27/TYPE28 . . . . . . . . . . . ... 15
TROUBLE DIAGNOSES . . . . . . . . . . ... 16
Wiring Diagram . . . . . . . . . . . . . ... 16
ID Registration Procedure . . . . . . . . . .. 17
Self-Diagnosis . . . . . . . . . . . . . . 17
How to Perform Trouble Diagnosis for Quick and
Accurate Repair . . . . . . . . . . . . . .. 19
INTRODUCTION . . . . . . . . . . . . . 19
WORK FLOW . . . . . . . . . . . . . .. 20
Preliminary Check . . . . . . . . . . . . .. 20
Symptom Chart . . . . . . . . . . . . . ... 21
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS . . . . . . . . . . . . . . . . . . 22
Inspection 1: Tyre Pressure Monitoring Antenna . 22
Inspection 2: Tyre Pressure Monitoring Sensor . .. 22
Inspection 3: Tyre Pressure Monitoring Control Unit... 22
Inspection 4: CAN Communication Line . . . . . 23
TROUBLE DIAGNOSIS FOR SYMPTOMS . . . .. 24
Inspection 1: Warning Lamp Does Not Come On
When Ignition Switch Is Turned On. . . . . . ... 24
Inspection 2: Warning LampStaysOn WhenIgnition
Switch Is Turned On. . . . . . . . . . . . .. 25
Inspection 3: “TYRE PRESSURE” Information In
Display Does Not Exist. . . . . . . . . . . .. 25
Inspection 4: IDRegistration Can Not Be Completed... 26
REMOVAL AND INSTALLATION . . . . . . . . 27
Tyre Pressure Monitoring Sensor . . . . . . ... 27
REMOVAL . . . . . . . . . . . . . . ... 27
INSTALLATION . . . . . . . . . . . . ... 27
SERVICE DATA . . . . . . . . . . . . . . 29
Road Wheel . . . . . . . . . . . . . . . 29
Tyre . . . . . . . . . . . . . . . . . . . 29
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст