Nissan Primera P12. Manual — part 611
LU-6
[YD.]
ENGINE OIL
6.
Start engine and check for oil leakage.
Changing Engine Oil
EBS00SJC
WARNING:
●
Be careful not to burn yourself, as the engine oil is hot.
●
Prolonged and repeated contact with used engine oil may
cause skin cancer: try to avoid direct skin contact with
used oil. If skin contact is made, wash thoroughly with soap
or hand cleaner as soon as possible.
1.
Put vehicle horizontally.
2.
Warm up engine, and check for oil leakage from engine compo-
nents.
3.
Stop engine and wait for 10 minutes.
4.
Remove drain plug and oil filler cap.
5.
Drain oil and refill with new engine oil.
Oil specification and viscosity:
●
API grade CF- 4.
●
Refer to
MA-15, "RECOMMENDED FLUIDS AND LUBRI-
Oil capacity (Approximate):
●
The refill capacity depends on the oil temperature and drain time. Use these specifications for reference
only.
Always use the dipstick to the determine when the proper amount of oil is in the engine.
CAUTION:
●
Be sure to clean drain plug and install with new washer.
●
The refill capacity depends on the oil temperature and drain time. Use these specifications for
reference only.
Always use the dipstick to the determine when the proper amount of oil is in the engine.
6.
Warm up engine and check area around drain plug and oil filter for oil leakage.
7.
Stop engine and wait for 10 minutes.
8.
Check oil level.
Oil pressure switch:
: 13 - 17 N·m (1.4 - 1.7 kg-m, 10 - 12 ft-lb)
PBIC0933E
Drain and refill
With oil filter change 5.2
(4-5/8 Imp qt)
Without oil filter change 4.9
(4-3/8 Imp qt)
Dry engine (engine overhaul) 6.3
(5-1/2 Imp qt)
Oil pan drain plug:
: 29 - 39 N·m (3.0 - 4.0 kg-m, 22 - 29 ft-lb)
SBIA0122E
OIL FILTER
LU-7
[YD.]
C
D
E
F
G
H
I
J
K
L
M
A
LU
OIL FILTER
PFP:15208
Removal and Installation
EBS00SJD
REMOVAL
CAUTION:
●
Be careful not to get burned when the engine and engine oil
are hot.
●
When removing, prepare a shop cloth to absorb any oil
leakage or spillage.
●
Do not allow engine oil to adhere to the drive belts.
●
Completely wipe off any oil that adhere to the engine and
the vehicle.
1.
Using a socket wrench [plane-to-plane width: 17 mm (0.67 in)],
loosen the filter body approximately four turns.
2.
Drain the oil after matching the “DRAIN” arrow mark at the bot-
tom of the filter to the protrusion on the oil filter bracket.
●
Catch the oil with a pan or cloth.
CAUTION:
●
The drained oil flows over the right surface of the filter.
●
Completely wipe clean any engine oil remaining on the
filter body or vehicle.
3.
Remove oil filter.
MBIB1013E
PBIC0745E
JLC291B
LU-8
[YD.]
OIL FILTER
4.
Remove the O-ring from the filter body.
●
Push the O-ring in one direction, lift the slack part using fin-
gers, and remove the O-ring from the filter body.
CAUTION:
Do not use wires or flat-bladed screwdrivers etc. as they
may cause damage to the filter.
INSTALLATION
1.
Completely remove all foreign objects adhering to the inside of the filter or O-ring mounting area (filter side
and bracket side).
2.
Install O-ring to the filter.
3.
Install the filter to the oil filter bracket.
4.
After warming up the engine, check for engine oil leakage.
5.
Check oil level and add engine oil. Refer to
.
JLC292B
Oil filter:
: 20 - 24 N·m (2.0 - 2.5 kg-m, 15 - 18 ft-lb)
OIL FILTER BRACKET
LU-9
[YD.]
C
D
E
F
G
H
I
J
K
L
M
A
LU
OIL FILTER BRACKET
PFP:15238
Removal and Installation
EBS00SJE
REMOVAL
1.
Remove the undercover.
2.
Steer the front wheel to the right.
3.
Remove the right splash cover.
4.
Remove the oil filter bracket bolt. Refer to
for cautions.
INSTALLATION
1.
Install all removed parts in the reverse order of removal.
●
Insert the top mounting bolt to the oil filter bracket beforehand, and set the oil filter bracket to the instal-
lation location.
●
After warning up the engine, check for engine oil leakage and oil level. Refer to
.
MBIB1012E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст