Nissan Primera P12. Manual — part 89
POWER DOOR LOCK — SUPER LOCK —
BL-65
C
D
E
F
G
H
J
K
L
M
A
B
BL
REAR RH SIDE
1.
CHECK DOOR LOCK SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock actuator RH harness connector.
3.
Check voltage between rear door lock actuator RH harness connector and ground.
OK or NG
OK
>> Replace rear door lock actuator RH.
NG
>> GO TO 2.
2.
CHECK DOOR LOCK ACTUATOR CIRCUIT
1.
Disconnect smart entrance control unit harness connector.
2.
Check continuity between rear door lock actuator RH harness
connector D66 terminal 5, 6 and smart entrance control unit har-
ness connector M43 terminal 52, 54.
OK or NG
OK
>> Replace smart entrance control unit.
NG
>> Repair or replace harness between smart entrance control unit and rear door lock actuator RH.
Connector
Terminals (wire color)
Door lock/
unlock switch
condition
Voltage (V)
(Approx.)
(+)
(
−
)
D66
5 (Y)
Ground
Lock
0
→
Battery voltage
→
0
6 (G/Y)
Unlock
0
→
Battery voltage
→
0
MIIB0463E
5 (Y) - 52 (Y)
: Continuity should exist.
6 (G/Y) - 54 (G/Y)
: Continuity should exist.
MIIB0467E
BL-66
POWER DOOR LOCK — SUPER LOCK —
Door Switch Check
EIS005HH
DRIVER SIDE
1.
CHECK DOOR SWITCH INPUT SIGNAL
WITH CONSULT-II
Check driver door switch signal (“DR DOOR SW”) in “DATA MONITOR” mode with CONSULT-II.
WITHOUT CONSULT-II
1.
Turn ignition switch OFF.
2.
Check voltage between smart entrance control unit harness
connector and ground.
OK or NG
OK
>> Door switch (driver side) is OK.
NG
>> GO TO 2.
2.
CHECK DRIVER SIDE DOOR SWITCH
1.
Disconnect front door switch (driver side) connector.
2.
Check continuity between front door switch (driver side) terminal
1 and ground part of door switch.
OK or NG
OK
>> Check harness for open or short between smart
entrance control unit and front door switch (driver side).
NG
>> Replace front door switch (driver side).
DR DOOR SW
Driver side door is open
: ON
Driver side door is closed
: OFF
MKIB0197E
Connector
Terminal (wire color)
Driver side door
condition
Voltage (V)
(Approx.)
( + )
( - )
M42
43 (R/W)
Ground
Open : (ON)
0
Closed : (OFF)
Battery voltage
MKIB0073E
Terminal
Door switch
Continuity
1
Ground part of
door switch
Pushed
No
Released
Yes
PIIA3351E
POWER DOOR LOCK — SUPER LOCK —
BL-67
C
D
E
F
G
H
J
K
L
M
A
B
BL
EXCEPT DRIVER SIDE
1.
CHECK OTHER DOORS SWITCHES INPUT SIGNAL
WITH CONSULT-II
Check other doors switch signal (“AS DOOR SW”, “RR DOOR SW” or “RR RH DOOR SW”) in “DATA MONI-
TOR” mode with CONSULT-II.
WITHOUT CONSULT-II
Check voltage between smart entrance control unit harness connector and ground.
OK or NG
OK
>> Door switch OK.
NG
>> GO TO 2.
2.
CHECK DOOR SWITCHES
1.
Disconnect each door switches harness connector.
2.
Check continuity between door switch terminal 1 and ground
part of door switch.
OK or NG
OK
>> Check harness for open or short between smart
entrance control unit and door switch.
NG
>> Replace malfunction door switch.
Each DOOR SW
Each door is open
: ON
Each door is closed
: OFF
MKIB0199E
Item
Connector
Terminal (wire color)
Condition
Voltage (V)
(Approx.)
(+)
(
−
)
Rear door
LH or RH
M42
39 (BR/W)
Ground
Open
0
Closed
Battery voltage
Passenger
side
44 (L/OR)
Open
0
Closed
Battery voltage
Rear door
LH or RH
45 (R/Y)
Open
0
Closed
Battery voltage
MKIB0583E
Terminal
Condition
Continuity
1
Ground part of
door switch
Pushed
No
Released
Yes
MKIB0584E
BL-68
POWER DOOR LOCK — SUPER LOCK —
Trunk Room Lamp Switch or Back Door Switch Check
EIS005HI
TRUNK ROOM LAMP SWITCH
1.
CHECK TRUNK ROOM LAMP SWITCH INPUT SIGNAL
With CONSULT- II
Check door switch “TRUNK OPEN SWITCH” in “DATA MONITOR” mode with CONSULT- II.
Without CONSULT- II
Check voltage between smart entrance control unit harness connector and ground.
OK or NG
OK
>> Trunk room lamp switch is OK.
NG
>> GO TO 2
2.
CHECK TRUNK ROOM LAMP SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect trunk room lamp switch harness connector.
3.
Check continuity between trunk room lamp switch terminals 1 and 2.
OK or NG
OK
>> Check the following.
●
Trunk room lamp switch ground circuit
●
Harness for open or short between smart entrance
control unit and trunk room lamp switch
NG
>> Replace trunk room lamp switch.
TRUNK OPEN SW
Trunk lid open
: ON
Trunk lid close
: OFF
SIIA1635E
Connector
Terminal (wire color)
Trunk lid
Voltage (V)
(Approx.)
(+)
(–)
M41
16 (G)
Ground
Closed
5
Open
0
SIIA1636E
Terminal
Trunk lid condition
Continuity
1
2
Opened
Yes
Closed
No
SIIA1637E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст