Nissan Primera P12. Manual — part 473
FAX-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Caution
EDS0015H
Observe the following precautions when disassembling and servicing drive shaft.
●
The joint of drive shaft cannot be disassembled. Do not attempt to disassemble it.
●
Perform work in a location which is as dust-free and dirt-free as possible.
●
Before disassembling and servicing, clean the outside of parts.
●
The disassembly and service location must be clean. Care must be taken to prevent parts from becoming
dirty and to prevent the entry of foreign objects.
●
Disassembled parts must be carefully reassembled in the correct order. If work is interrupted, a clean
cover must be placed over parts.
●
Paper shop cloths must be used. Fabric shop cloths must not be used because of the danger of lint adher-
ing to parts.
●
Disassembled parts (except for rubber parts) should be cleaned with kerosene which shall be removed by
blowing with air or wiping with paper shop cloths.
Precautions for Brake System
EDS0015I
●
When installing rubber parts, final tightening must be carried out
under unladen condition* with tires on ground.
*: Fuel, radiator coolant and engine oil full. Spare tire, jack, hand
tools and mats in designated positions.
●
Use flare nut wrench when removing or installing brake tubes.
●
After installing removed suspension parts, check wheel align-
ment and adjust if necessary.
●
Always torque brake lines when installing.
SBR686C
PREPARATION
FAX-3
C
E
F
G
H
I
J
K
L
M
A
B
FAX
PREPARATION
PFP:00002
Special Service Tools
EDS0015J
Tool name
Tool number
Description
Hub lock nuts wrench
KV40104000
Installing the drive shaft
Installing and removing hub lock nut
Protector
KV38107800
a: 29 mm (1.14 in) dia.
KV38105500
a: 40 mm (1.57 in) dia.
Installing the drive shaft
Drift
ST17130000
a: 32 mm (1.26 in) dia.
b: 60 mm (1.57 in) dia.
Disassembling support bearings
Drift
ST35271000
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.
Assembling support bearings
Installing wheel bearings
Drift
ST33252000
a: 82 mm (3.23 in) dia.
b: 60 mm (2.36 in) dia.
Assembling support bearings
Drift
KV38100500
a: 80 mm (3.15 in) dia.
b: 60 mm (2.36 in) dia.
Installing ABS sensor rotors
Collar
KV40101840
a: 67 mm (2.64 in) dia.
b: 85 mm (3.35 in) dia.
Installing ABS sensor rotors
ZZA0802D
ZZA0835D
ZZA0836D
ZZA0837D
ZZA0838D
ZZA0701D
ZZA1113D
FAX-4
PREPARATION
Sliding hammer
ST36230000
Removing wheel hubs
Attachment
KV40104100
Removing wheel hubs
Drift
ST33061000
a: 28.5 mm (1.122 in) dia.
b: 38.0 mm (1.50 in) dia.
Removing inner race on outer side of wheel
bearings
Bearing replacer
ST30031000
Removing inner race on outer side of wheel
bearings
Drift
KV40100621
a: 76 mm (2.99 in) dia.
b: 69 mm (2.72 in) dia.
Installing wheel bearings
Drift
ST30613000
a: 72 mm (2.83 in) dia.
b: 48 mm (1.89 in) dia.
Installing and removing wheel bearing
Drift
ST27863000
a: 75 mm (2.95 in) dia.
b: 62 mm (2.44 in) dia.
Installing and removing wheel bearing
Tool name
Tool number
Description
ZZA0803D
ZZA0804D
ZZA0969D
ZZA0700D
ZZA0814D
ZZA0830D
ZZA0832D
PREPARATION
FAX-5
C
E
F
G
H
I
J
K
L
M
A
B
FAX
Commercial Service Tools
EDS0015K
Drift
ST33400001
a: 72 mm (2.83 in) dia.
b: 63 mm (2.48 in) dia.
Installing wheel hub
Boot band tool
KV40107300
Installing boot bands
Tool name
Tool number
Description
ZZA0814D
ZZA1229D
Tool name
Description
1. Flare nut crowfoot
2. Torque wrench
a: 10 mm (0.39 in)
Removing and installing brake piping
S-NT360
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст