Nissan Primera P12. Manual — part 352
DTC P1275 FUEL PUMP
EC-593
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
6.
CHECK INTERMITTENT INCIDENT
Refer to
EC-408, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS015BJ
FUEL PUMP
1.
Check continuity between fuel pump terminals 1 and 2.
2.
If NG, replace fuel pump.
Removal and Installation
EBS015BK
FUEL PUMP
Refer to
.
Continuity should exist.
MBIB0623E
EC-594
[YD (WITHOUT EURO-OBD)]
DTC P2135 APP SENSOR
DTC P2135 APP SENSOR
PFP:18002
Description
EBS015BL
The accelerator pedal position sensor is installed on the upper end
of the accelerator pedal assembly. The sensors detect the accelera-
tor pedal position and sends a signal to the ECM. The ECM uses the
signal to determine the amount of fuel to be injected.
CONSULT-II Reference Value in Data Monitor Mode
EBS015BM
Specification data are reference values.
*: This signal is converted by ECM internally. Thus, it differs from ECM terminal voltage.
ECM Terminals and Reference Value
EBS015BN
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
PBIB1741E
MONITOR ITEM
CONDITION
SPECIFICATION
ACCEL POS SEN*
●
Ignition switch: ON
(Engine stopped)
Accelerator pedal: fully released
0.2 - 0.7V
Accelerator pedal: fully depressed
3.9 - 4.9V
ACCEL SEN 2*
●
Ignition switch: ON
(Engine stopped)
Accelerator pedal: fully released
0.1 - 0.4V
Accelerator pedal: fully depressed
1.9 - 2.4V
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage)
82
L/R
Accelerator pedal position
sensor 1 power supply
[Ignition switch ON]
Approximately 5.3V
83
L/W
Accelerator pedal position
sensor 1
[Ignition switch ON]
●
Engine stopped
●
Accelerator pedal fully released
0.5 - 1.0V
[Ignition switch ON]
●
Engine stopped
●
Accelerator pedal fully depressed
4.2 - 5.2V
84
L
Accelerator pedal position
sensor 1 ground
[Ignition switch ON]
Approximately 0.3V
85
—
Sensor ground
(Accelerator pedal posi-
tion sensor shield circuit)
[Ignition switch ON]
Approximately 0.3V
90
R
Accelerator pedal position
sensor 2 power supply
[Ignition switch ON]
Approximately 5.3V
DTC P2135 APP SENSOR
EC-595
[YD (WITHOUT EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
On Board Diagnosis Logic
EBS015BO
The MI will not light up for this self-diagnosis.
DTC Confirmation Procedure
EBS015BP
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 5 seconds.
4.
Depress accelerator pedal slowly spending 5 seconds, and then
release it slowly spending 5 seconds.
5.
If DTC is detected, go to
EC-597, "Diagnostic Procedure"
.
91
W
Accelerator pedal position
sensor 2
[Ignition switch ON]
●
Engine stopped
●
Accelerator pedal fully released
0.4 - 0.7V
[Ignition switch ON]
●
Engine stopped
●
Accelerator pedal fully depressed
2.2 - 2.7V
92
B
Accelerator pedal position
sensor 2 ground
[Ignition switch ON]
Approximately 0.3V
TERMI-
NAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA
(DC Voltage)
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P2135
Accelerator pedal position
sensor 1, 2 signal correla-
tion
The correlation between APP sensor 1 signal
and APP sensor 2 signal is out of the normal
range.
●
Harness or connectors
(The APP sensor circuit is open or
shorted.)
●
Accelerator pedal position sensor
SEF817Y
EC-596
[YD (WITHOUT EURO-OBD)]
DTC P2135 APP SENSOR
Wiring Diagram
EBS015BQ
MBWA0433E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст