Nissan Primera P12. Manual — part 83
POWER DOOR LOCK SYSTEM
BL-41
C
D
E
F
G
H
J
K
L
M
A
B
BL
Key Switch Check
EIS005H5
1.
CHECK KEY SWITCH INPUT SIGNAL
WITH CONSULT-II
Check key switch signal (“KEY IN DETECT”) in “DATA MONITOR”
mode with CONSULT-II.
WITHOUT CONSULT-II
Check voltage between smart entrance control unit harness connector M41 terminal 5 and ground.
OK or NG
OK
>> Key switch is OK.
NG
>> GO TO 2.
2.
CHECK KEY SWITCH
1.
Disconnect key switch connector.
2.
Check continuity between key switch terminal 1 and 2.
OK or NG
OK
>> Check the following.
●
10A fuse [No. 12, located in fuse block (J/B)]
●
Harness for open or short between key switch and
fuse
●
Harness for open or short between smart entrance control unit and key switch
NG
>> Replace key switch.
KEY IN DETECT
Key is inserted in ignition cylinder
: ON
Key is removed from ignition key cylinder
: OFF
MKIB0200E
Connector
Terminals (wire color)
Condition
(Door lock/
unlock switch)
Voltage (V)
(Approx.)
(+)
(
−
)
M41
5 (B/R)
Ground
Key is
inserted
Battery voltage
Key is
removed
0
MKIB0585E
Terminal
Condition
Continuity
1
2
Key is inserted
Yes
Key is removed
No
MKIB0586E
BL-42
POWER DOOR LOCK — SUPER LOCK —
POWER DOOR LOCK — SUPER LOCK —
PFP:24814
System Description
EIS005H6
OUTLINE
Power door lock system with super lock and key reminder is controlled by smart entrance control unit. Super
lock has a higher anti-theft performance than conventional power door lock systems.
When super lock is in released condition, lock knob operation locks or unlocks door.
When super lock is in set condition, lock knob operation cannot lock nor unlock door.
OPERATION
Power door lock/unlock and super lock set/release operation by door key cylinder
●
With the key inserted into driver door key cylinder, turning it to LOCK will lock all doors and set super lock.
(Super lock will not be set while key is inserted in the ignition key cylinder.)
●
With the key inserted into driver door key cylinder, turning it to UNLOCK will unlock all doors and release
super lock.
Power door lock/unlock and super lock set/release operation by remote controller (If
equipped)
●
Pressing remote controller LOCK button will lock all doors and set super lock. (Super lock will not be set
while key is inserted in the ignition key cylinder.)
●
Pressing remote controller UNLOCK button once will unlock driver door and release super lock. Then, if
an unlock signal is sent from the remote controller again within 5 seconds, all other doors will be unlocked.
Power door lock and super lock release operation
●
When the super lock is set, turning the ignition key switch to ON will release the super lock. All doors will
unlock once, but then immediately lock again.
Power door lock/unlock operation by lock/unlock switch
●
With door lock/unlock switch on center console setting to LOCK will lock all doors.
●
With door lock/unlock switch on center console setting to UNLOCK will unlock all doors.
Door lock/unlock switch operation cannot control super lock
Child lock system
●
The system has a child lock switch that mechanically latches in the ON and OFF condition. Child locks
can only be operated when the ignition is ON and for 30 seconds after the ignition is OFF.
Child lock indicator (Located in combination meter) operation
Key reminder system
●
If the ignition key is in the ignition key cylinder and driver door is open, setting door lock/unlock switch,
lock knob, key or remote controller to “LOCK” locks the door once but then immediately unlocks all doors.
(signal from door unlock sensor driver side)
System initialization
●
System initialization is required when battery cables are reconnected. Conduct the following to release
super lock once;
–
insert the key into the ignition key cylinder and turn it to ON.
–
LOCK/UNLOCK operation using door key cylinder or remote controller.
Indicator ON
Ignition switch: ON
Child lock set
Indicator ON for 30 seconds
Child lock not completely set
Indicator blinks & beep warning for 10 seconds
Indicator OFF
Child lock switch
released
Child lock released
Indicator blinks for 10 seconds
Child lock not completely
released
Indicator blinks & beep warning for 10 seconds
Ignition switch: OFF
—
Indicator OFF
POWER DOOR LOCK — SUPER LOCK —
BL-43
C
D
E
F
G
H
J
K
L
M
A
B
BL
Schematic
EIS005H7
MKWA0102E
BL-44
POWER DOOR LOCK — SUPER LOCK —
Wiring Diagram — S/LOCK —
EIS005H8
MKWA0672E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст