Nissan Primera P12. Manual — part 264
DTC P0605 ECM
EC-241
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0605 ECM
PFP:23710
Description
EBS013PE
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
On Board Diagnosis Logic
EBS013PF
DTC Confirmation Procedure
EBS013PG
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 5 seconds.
4.
If 1st trip DTC is detected, go to
EC-242, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
MBIB0625E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0605
Engine control module
(ROM)
ECM ROM is malfunctioning.
●
ECM
SEF817Y
EC-242
[YD (WITH EURO-OBD)]
DTC P0605 ECM
Diagnostic Procedure
EBS013PH
1.
INSPECTION START
With CONSULT-II
1.
Turn ignition switch ON.
2.
Select “SELF DIAG RESULTS” mode with CONSULT-II.
3.
Touch “ERASE”.
4.
Perform
EC-241, "DTC Confirmation Procedure"
, again.
5.
Is 1st trip DTC P0605 displayed again?
With GST
1.
Turn ignition switch ON.
2.
Select MODE4 with GST.
3.
Touch “ERASE”.
4.
Perform
EC-241, "DTC Confirmation Procedure"
, again.
5.
Is 1st trip DTC P0605 displayed again?
Yes or No
Yes
>> GO TO 2.
No
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to
.
3.
Perform Fuel Pump Learning Value Clearing. Refer to
EC-29, "Fuel Pump Learning Value Clearing"
.
>> INSPECTION END
DTC P0606 ECM
EC-243
[YD (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0606 ECM
PFP:23710
Description
EBS013PI
The ECM consists of a microcomputer and connectors for signal
input and output and for power supply. The ECM controls the engine.
On Board Diagnosis Logic
EBS013PJ
DTC Confirmation Procedure
EBS013PK
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
WITH CONSULT-II
1.
Turn ignition switch ON.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
Wait at least 5 seconds.
4.
If DTC is detected, go to
EC-244, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
MBIB0625E
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0606
Engine control module
(Processor)
ECM calculation function is malfunctioning.
●
ECM
SEF817Y
EC-244
[YD (WITH EURO-OBD)]
DTC P0606 ECM
Diagnostic Procedure
EBS013PL
1.
INSPECTION START
With CONSULT-II
1.
Turn ignition switch ON.
2.
Select “SELF DIAG RESULTS” mode with CONSULT-II.
3.
Touch “ERASE”.
4.
Perform
EC-243, "DTC Confirmation Procedure"
, again.
5.
Is 1st trip DTC P0606 displayed again?
With GST
1.
Turn ignition switch ON.
2.
Select MODE4 with GST.
3.
Touch “ERASE”.
4.
Perform
EC-243, "DTC Confirmation Procedure"
, again.
5.
Is 1st trip DTC P0606 displayed again?
Yes or No
Yes
>> GO TO 2.
No
>> INSPECTION END
2.
REPLACE ECM
1.
Replace ECM.
2.
Perform initialization of NATS system and registration of all NATS ignition key IDs. Refer to
.
3.
Perform “Fuel Pump Learning Value Clearing”. Refer to
EC-29, "Fuel Pump Learning Value Clearing"
.
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст