Nissan Juke (2016 year). Service Repair Manual — part 550

WHEEL ALIGNMENT

RSU-23

< PERIODIC MAINTENANCE >

[AWD]

C

D

F

G

H

I

J

K

L

M

A

B

RSU

N

O

P

2. Adjust camber and toe-in by turning upper link adjusting bolt (1)

and lower link adjusting bolt (2) alternately.

NOTE:

• Refer to the table below for easier adjustment.

- Obtain the amount of camber and toe-in by calculating the difference between the measurement result

and the standard value.

- Obtain the needed adjustment amount from the graph and move adjusting bolts, respectively.

3. After adjustment, tighten mounting nuts of upper link and lower link on the suspension member side.

CAUTION:

When tightening nut to the specified torque, the bolt must be fixed with a wrench.

4. Adjust neutral position of steering angle sensor. Refer to

BRC-63, "Work Procedure"

.

A

: Left side

B

: Right side

Upper link adjusting bolt
Positive direction

: Upper link slides into inner side of vehicle.

Negative direction

: Upper link slides into outer side of vehicle.

Lower link adjusting bolt
Positive direction

: Lower link slides into outer side of vehicle.

Negative direction

: Lower link slides into inner side of vehicle.

JPEIB0259ZZ

JPEIB0260GB

Revision: November 2015

2016 JUKE

RSU-24

< REMOVAL AND INSTALLATION >

[AWD]

REAR SHOCK ABSORBER

REMOVAL AND INSTALLATION

REAR SHOCK ABSORBER

Exploded View

INFOID:0000000012200412

Removal and Installation

INFOID:0000000012200413

REMOVAL

1. Remove tires with power tool. Refer to

WT-39, "Removal and Installation"

.

2. Set suitable jack under suspension arm.

CAUTION:

• Never damage the suspension arm with a jack.

• Check the stable condition when using a jack.

3. Remove shock absorber mounting bolt and nut (lower side).
4. Remove shock absorber mask. Refer to

INT-33, "Exploded View"

.

5. Remove cap.
6. Remove piston rod lock nut (1), and then remove washer and

bushing.

NOTE:

To loosen piston rod lock nut, fix the tip (A) of the piston rod.

7. Remove shock absorber assembly.
8. Remove bushing, distance tube, bound bumper cover, and

bound bumper from shock absorber.

9. Perform inspection after removal. Refer to

RSU-25, "Inspection"

.

INSTALLATION

1.

Suspension arm

2.

Shock absorber

3.

Bound bumper

4.

Bound bumper cover

5.

Washer

6.

Bushing

7.

Distance tube

8.

Piston rod lock nut

9.

Cap

: Vehicle front

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JPEIB0257GB

JPEIB0241ZZ

Revision: November 2015

2016 JUKE

REAR SHOCK ABSORBER

RSU-25

< REMOVAL AND INSTALLATION >

[AWD]

C

D

F

G

H

I

J

K

L

M

A

B

RSU

N

O

P

Note the following, and install in the reverse order of removal.

• To install bushings (1), securely insert protrusion (A) into the hole

on the vehicle body side.

• Install washer (1) in the direction shown in the figure.

• Perform final tightening of bolts and nuts at the shock absorber

lower side (rubber bushing), under unladen conditions with tires on

level ground.

• Hold a head (A) of shock absorber piston rod nut to have it rotate,

then tighten the piston rod lock nut (1) to the specified torque.

CAUTION:

Never reuse piston rod lock nut.

• When installing the cap, securely engage the cap groove (A) with

the flange on the vehicle side.

• Perform inspection after installation. Refer to

RSU-25, "Inspec-

tion"

.

• After replacing the shock absorber, always follow the disposal pro-

cedure to discard the shock absorber. Refer to

RSU-25, "Inspec-

tion"

.

Inspection

INFOID:0000000012200414

INSPECTION AFTER REMOVAL

Shock Absorber

Check the following items, and replace the part if necessary.

• Shock absorber for deformation, cracks, and other damage.

• Piston rod for damage, uneven wear, and distortion.

• Oil leakage.

JPEIB0240ZZ

: Bushing side

JPEIB0248ZZ

JPEIB0241ZZ

JPEIB0244ZZ

Revision: November 2015

2016 JUKE

RSU-26

< REMOVAL AND INSTALLATION >

[AWD]

REAR SHOCK ABSORBER

Bound Bumper, Bushing

Check for cracks and damage. Replace it if necessary.

Washer, Bound Bumper Cover, Distance Tube

• Check for cracks and damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

1. Check wheel alignment. Refer to

RSU-22, "Inspection"

.

2. Adjust neutral position of steering angle sensor. Refer to

BRC-63, "Work Procedure"

.

Disposal

INFOID:0000000012200415

1. Set shock absorber horizontally to the ground with the piston rod fully extracted.
2. Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position ( ) from top

as shown in the figure to release gas gradually.

CAUTION:

• Wear eye protection (safety glasses).

• Wear gloves.

• Be careful with metal chips or oil blown out by the com-

pressed gas.

NOTE:

• Drill vertically in this direction.

• Directly to the outer tube avoiding brackets.

• The gas is clear, colorless, odorless, and harmless.

3. Position the drilled hole downward and drain oil by moving the piston rod several times.

CAUTION:

Dispose of drained oil according to the law and local regulations.

A

: 20 – 30 mm (0.79 – 1.18 in)

JPEIA0161ZZ

Revision: November 2015

2016 JUKE

COIL SPRING

RSU-27

< REMOVAL AND INSTALLATION >

[AWD]

C

D

F

G

H

I

J

K

L

M

A

B

RSU

N

O

P

COIL SPRING

Exploded View

INFOID:0000000012200416

Removal and Installation

INFOID:0000000012200417

REMOVAL

1. Remove tires with power tool. Refer to

WT-39, "Removal and Installation"

.

2. Remove wheel sensor and sensor harness. Refer to

BRC-150, "REAR WHEEL SENSOR : Removal and

Installation"

.

3. Set jack under suspension arm.

CAUTION:

• Never damage the suspension arm with a jack.

• Check the stable condition when using a jack.

4. Separate rear shock absorber lower side form suspension arm. Refer to

RSU-24, "Removal and Installa-

tion"

.

5. Separate upper link from suspension arm.
6. Slowly lower jack, then remove upper rubber seat, coil spring and lower rubber seat from suspension arm.

CAUTION:

Operate while checking that jack supporting status is stable.

7. Perform inspection after removal. Refer to

RSU-28, "Inspection"

.

INSTALLATION

Note the following, and install in the reverse order of removal.

1.

Upper rubber seat

2.

Coil spring

3.

Lower rubber seat

4.

Suspension arm

: Vehicle front

JPEIB0258ZZ

Revision: November 2015

2016 JUKE

RSU-28

< REMOVAL AND INSTALLATION >

[AWD]

COIL SPRING

• Install the lower rubber seat a projection (A) is attached as suspen-

sion arm mounting hole (B).

• Match up lower rubber seat indentions and suspension arm

grooves and attach.

• Install coil spring (1) lower end with spring end holding section (B)

of lower rubber seat (2).

• Mach up coil spring (1) upper end to the centre of upper rubber

seat (2) projection (A) as shown in figure.

• Perform inspection after installation. Refer to

RSU-28, "Inspec-

tion"

.

Inspection

INFOID:0000000012200418

INSPECTION AFTER REMOVAL

Check rubber seat and coil spring for deformation, crack, and damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

1. Check wheel sensor harness for proper connection. Refer to

BRC-148, "REAR WHEEL SENSOR :

Exploded View"

.

2. Check wheel alignment. Refer to

RSU-22, "Inspection"

.

3. Adjust neutral position of steering angle sensor. Refer to

BRC-63, "Work Procedure"

.

JPEIB0261ZZ

Dimension (A)

: 10 mm (0.20 in) or less

JSEIA0943ZZ

JSEIA0944ZZ

Revision: November 2015

2016 JUKE

SUSPENSION ARM

RSU-29

< REMOVAL AND INSTALLATION >

[AWD]

C

D

F

G

H

I

J

K

L

M

A

B

RSU

N

O

P

SUSPENSION ARM

Exploded View

INFOID:0000000012200419

Removal and Installation

INFOID:0000000012200420

REMOVAL

1. Remove tires with power tool. Refer to

WT-39, "Removal and Installation"

.

2. Drain brake fluid. Refer to

BR-12, "Draining"

.

3. Remove wheel sensor and sensor harness. Refer to

BRC-150, "REAR WHEEL SENSOR : Removal and

Installation"

.

4. Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to

BR-64, "BRAKE CALIPER ASSEMBLY : Removal and Installation"

.

CAUTION:

Never depress brake pedal while brake caliper is removed.

5. Remove disc rotor. Refer to

RAX-16, "Removal and Installation"

.

6. Remove parking brake cable mounting bolt. Refer to

PB-7, "Removal and Installation"

.

7. Separate the brake tube from the brake hose, and remove lock plate. Refer to

BR-27, "REAR : Exploded

View"

.

8. Remove wheel hub and bearing assembly. Refer to

RAX-16, "Removal and Installation"

.

9. Remove parking brake shoe and back plate. Refer to

PB-9, "Removal and Installation"

.

1.

Rear suspension member

2.

Adjusting bolt

3.

Upper link

4.

Eccentric disk

5.

Lower link

6.

Suspension arm bracket

7.

Suspension arm

: Vehicle front

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JPEIB0262GB

Revision: November 2015

2016 JUKE

RSU-30

< REMOVAL AND INSTALLATION >

[AWD]

SUSPENSION ARM

10. Set jack under suspension arm.

CAUTION:

• Never damage the suspension arm with a jack.

• Check the stable condition when using a jack.

11. Remove stabilizer link. Refer to

RSU-35, "Removal and Installation"

.

12. Remove upper link from suspension arm. Refer to

RSU-33, "Removal and Installation"

.

13. Remove lower link from suspension arm. Refer to

RSU-31, "Removal and Installation"

.

14. Remove coil spring from suspension arm. Refer to

RSU-27, "Removal and Installation"

.

15. Remove suspension arm bracket from vehicle.
16. Remove suspension arm from suspension arm bracket.
17. Perform inspection after removal. Refer to

RSU-30, "Inspection"

.

INSTALLATION

Note the following, and install in the reverse order of removal.

• Perform final tightening of rear suspension member installation position (rubber bushing), under unladen

conditions with tires on level ground.

• Never reuse suspension arm mounting nut.

• Perform inspection after installation. Refer to

RSU-30, "Inspection"

.

Inspection

INFOID:0000000012200421

INSPECTION AFTER REMOVAL

Check suspension arm and bushing for deformation, cracks or damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

1. Check wheel sensor harness for proper connection. Refer to

BRC-148, "REAR WHEEL SENSOR :

Exploded View"

.

2. Adjust parking brake operation (stroke). Refer to

PB-4, "Inspection and Adjustment"

.

3. Check wheel alignment. Refer to

RSU-22, "Inspection"

.

4. Adjust neutral position of steering angle sensor. Refer to

BRC-63, "Work Procedure"

.

Revision: November 2015

2016 JUKE