Nissan Juke (2016 year). Service Repair Manual — part 469
LAN
CAN COMMUNICATION CIRCUIT
LAN-91
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 2)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Is the measurement value within the specification?
YES
>> GO TO 5.
NO
>> Replace the ECM and/or the BCM.
5.
CHECK SYMPTOM
Connect all the connectors. Check if the symptoms described in the “Symptom (Results from interview with
customer)” are reproduced.
Inspection result
Reproduced>>GO TO 6.
Non-reproduced>>Start the diagnosis again. Follow the trouble diagnosis procedure when past error is
detected.
6.
CHECK UNIT REPRODUCTION
Perform the reproduction test as per the following procedure for each unit.
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect one of the unit connectors of CAN communication system.
NOTE:
ECM and BCM have a termination circuit. Check other units first.
4. Connect the battery cable to the negative terminal. Check if the symptoms described in the “Symptom
(Results from interview with customer)” are reproduced.
NOTE:
Although unit-related error symptoms occur, do not confuse them with other symptoms.
Inspection result
Reproduced>>Connect the connector. Check other units as per the above procedure.
Non-reproduced>>Replace the unit whose connector was disconnected.
Revision: November 2015
2016 JUKE
LAN-92
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 3)]
MAIN LINE BETWEEN IPDM-E AND HVAC CIRCUIT
DTC/CIRCUIT DIAGNOSIS
MAIN LINE BETWEEN IPDM-E AND HVAC CIRCUIT
Diagnosis Procedure
INFOID:0000000012200563
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector E105
-
Harness connector M77
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect the following harness connectors.
-
IPDM E/R
-
Harness connectors E105 and M77
2. Check the continuity between the IPDM E/R harness connector and the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the IPDM E/R and the harness connector E105.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Disconnect the connector of A/C amp.
2. Check the continuity between the harness connector and the A/C auto amp. harness connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the IPDM E/R and the A/C auto amp.
NO
>> Repair the main line between the harness connector M77 and the A/C auto amp.
IPDM E/R harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
E13
27
E105
1
Existed
26
6
Existed
Harness connector
A/C auto amp. harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M77
1
M50
6
Existed
6
7
Existed
Revision: November 2015
2016 JUKE
LAN
MAIN LINE BETWEEN HVAC AND DLC CIRCUIT
LAN-93
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 3)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MAIN LINE BETWEEN HVAC AND DLC CIRCUIT
Diagnosis Procedure
INFOID:0000000012200564
1.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect the following harness connectors.
-
ECM
-
A/C auto amp.
4. Check the continuity between the A/C auto amp. harness connector and the data link connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the A/C auto amp. and the data link connec-
tor.
NO
>> Repair the main line between the A/C auto amp. and the data link connector.
A/C auto amp. harness connector
Data link connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M50
6
M4
6
Existed
7
14
Existed
Revision: November 2015
2016 JUKE
LAN-94
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 3)]
ECM BRANCH LINE CIRCUIT
ECM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200565
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the ECM for damage, bend and loose connection (unit side and
connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of ECM.
2. Check the resistance between the ECM harness connector terminals.
-
For NISMO RS models
-
Except for NISMO RS models
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the ECM branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the ECM. Refer to the following.
• For NISMO RS models:
• Except for NISMO RS models:
Is the inspection result normal?
YES (Present error)>>Replace the ECM. Refer to the following.
• For NISMO RS models:
EC-590, "Removal and Installation"
• Except for NISMO RS models:
EC-1256, "Removal and Installation"
YES (Past error)>>Error was detected in the ECM branch line.
NO
>> Repair the power supply and the ground circuit.
ECM harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E18
100
99
Approx. 108 – 132
ECM harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E19
124
123
Approx. 108 – 132
Revision: November 2015
2016 JUKE
LAN
ABS BRANCH LINE CIRCUIT
LAN-95
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 3)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ABS BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200566
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the ABS actuator and electric unit (control unit) for damage, bend
and loose connection (unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of ABS actuator and electric unit (control unit).
2. Check the resistance between the ABS actuator and electric unit (control unit) harness connector termi-
nals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the ABS actuator and electric unit (control unit) branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the ABS actuator and electric unit (control unit). Refer to
BRC-129, "Diagnosis Procedure"
.
Is the inspection result normal?
YES (Present error)>>Replace the ABS actuator and electric unit (control unit). Refer to
.
YES (Past error)>>Error was detected in the ABS actuator and electric unit (control unit) branch line.
NO
>> Repair the power supply and the ground circuit.
ABS actuator and electric unit (control unit) harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E35
22
9
Approx. 54 – 66
Revision: November 2015
2016 JUKE
LAN-96
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 3)]
IPDM-E BRANCH LINE CIRCUIT
IPDM-E BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200567
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the IPDM E/R for damage, bend and loose connection (unit side
and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of IPDM E/R.
2. Check the resistance between the IPDM E/R harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the IPDM E/R branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the IPDM E/R. Refer to
Is the inspection result normal?
YES (Present error)>>Replace the IPDM E/R. Refer to
PCS-37, "Removal and Installation"
YES (Past error)>>Error was detected in the IPDM E/R branch line.
NO
>> Repair the power supply and the ground circuit.
IPDM E/R harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E13
27
26
Approx. 54 – 66
Revision: November 2015
2016 JUKE
LAN
A-BAG BRANCH LINE CIRCUIT
LAN-97
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 3)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
A-BAG BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200568
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the air bag diagnosis sensor unit for damage, bend and loose con-
nection (unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the main harness.
2.
CHECK AIR BAG DIAGNOSIS SENSOR UNIT
Check the air bag diagnosis sensor unit. Refer to
Is the inspection result normal?
YES
>> Replace the main harness.
NO
>> Replace parts whose air bag system has a malfunction.
Revision: November 2015
2016 JUKE
LAN-98
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 3)]
AVM BRANCH LINE CIRCUIT
AVM BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000012200569
1.
CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the around view monitor control unit for damage, bend and loose
connection (unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect the connector of around view monitor control unit.
2. Check the resistance between the around view monitor control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the around view monitor control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the around view monitor control unit. Refer to
"AROUND VIEW MONITOR CONTROL UNIT : Diagnosis Procedure"
.
Is the inspection result normal?
YES (Present error)>>Replace the around view monitor control unit. Refer to
AV-190, "Removal and Installa-
.
YES (Past error)>>Error was detected in the around view monitor control unit branch line.
NO
>> Repair the power supply and the ground circuit.
Around view monitor control unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
M98
26
24
Approx. 54 – 66
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст