Nissan Juke (2016 year). Service Repair Manual — part 373
EXL-206
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
HEADLAMP
REMOVAL AND INSTALLATION
HEADLAMP
Exploded View
INFOID:0000000012201781
REMOVAL
DISASSEMBLY
1.
Headlamp assembly
: Vehicle front
: N·m (kg-m, in-lb)
JMLIA5396GB
Revision: November 2015
2016 JUKE
HEADLAMP
EXL-207
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal and Installation
INFOID:0000000012201782
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-119, "Precautions for Removing Battery Terminal"
REMOVAL
1. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
2. Remove headlamp mounting bolts.
3. Pull out headlamp assembly forward the vehicle, and then disconnect the connector before removing the
headlamp assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000012201783
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-119, "Precautions for Removing Battery Terminal"
• After installing the bulb, install the back cover and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
1.
Headlamp assembly
2.
Halogen bulb (LO)
3.
Back cover A
4.
Halogen bulb (HI)
5.
Back cover B
: Vehicle front
JMLIA5398ZZ
Revision: November 2015
2016 JUKE
EXL-208
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
HEADLAMP
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HALOGEN BULB (LO)
Left Side of The Vehicle
1. Remove fixing clips (A) of air cleaner assembly (1).
2. While pulling up on the (B) portion of the air duct inlet (upper)
(2), disengage of the portion (C), and then remove air duct inlet
(upper) as shown by the arrow in the figure.
3. Remove back cover A.
4. Disconnect halogen bulb harness connector.
5. Rotate halogen bulb (LO) counterclockwise and lock it, and then remove halogen bulb.
Right Side of The Vehicle
1. Remove washer tank inlet. Refer to
WW-43, "Removal and Installation"
.
2. Remove back cover A.
3. Disconnect halogen bulb harness connector.
4. Rotate halogen bulb (LO) counterclockwise and lock it, and then remove halogen bulb.
HALOGEN BULB (HI)
Left Side of The Vehicle
1. Remove fixing clips (A) of air cleaner assembly (1).
2. While pulling up on the (B) portion of the air duct inlet (upper)
(2), disengage of the portion (C), and then remove air duct inlet
(upper) as shown by the arrow in the figure.
3. Remove back cover B.
4. Disconnect halogen bulb harness connector.
5. Rotate halogen bulb clockwise and unlock it, and then remove halogen bulb from headlamp assembly.
Right Side of The Vehicle
1. Remove washer tank inlet. Refer to
WW-43, "Removal and Installation"
.
2. Remove back cover B.
3. Disconnect halogen bulb harness connector.
4. Rotate halogen bulb counterclockwise and unlock it, and then remove halogen bulb from headlamp
assembly.
Disassembly and Assembly
INFOID:0000000012201784
DISASSEMBLY
1. Remove back cover A.
2. Disconnect halogen bulb harness connector.
: Vehicle front
JMLIA5700ZZ
: Vehicle front
JMLIA5700ZZ
Revision: November 2015
2016 JUKE
HEADLAMP
EXL-209
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3. Rotate halogen bulb (LO) counterclockwise and lock it, and then remove halogen bulb.
4. Remove back cover B.
5. Disconnect halogen bulb harness connector.
6. Remove halogen bulb (HI).
Left side of the vehicle
• Rotate halogen bulb (HI) clockwise and lock it, and then remove halogen bulb.
Right side of the vehicle
• Rotate halogen bulb (HI) counterclockwise and lock it, and then remove halogen bulb.
ASSEMBLY
Note the following item, and then assemble in the reverse order of disassembly.
CAUTION:
After installing the bulb, install the back cover and the bulb socket securely for watertightness.
Revision: November 2015
2016 JUKE
EXL-210
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
FRONT COMBINATION LAMP
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000012201785
REMOVAL
DISASSEMBLY
1.
Front combination lamp
: N·m (kg-m, in-lb)
JMLIA5399GB
JMLIA6148ZZ
Revision: November 2015
2016 JUKE
FRONT COMBINATION LAMP
EXL-211
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal and Installation
INFOID:0000000012201786
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-119, "Precautions for Removing Battery Terminal"
REMOVAL
1. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
2. Remove front combination lamp mounting bolts and nut.
3. Pull out front combination lamp forward the vehicle, and then disconnect connector before removing the
front combination lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Interference of front combination lamp lens with front fender may cause intrusion of water into front
combination lamp or rusting of fender due to damage of painted surface. Be careful to operate without
allowing parts to interfere with each other.
Replacement
INFOID:0000000012201787
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-119, "Precautions for Removing Battery Terminal"
• After installing the bulb, install the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
PARKING LAMP BULB
CAUTION:
Replacement of a single part is not possible due to the adoption of LED. For replacement, replace
front combination lamp as a set. Refer to
EXL-211, "Removal and Installation"
.
FRONT TURN SIGNAL LAMP BULB
1. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
2. Remove front turn signal lamp bulb from the front turn signal lamp bulb socket.
FRONT SIDE MARKER LAMP BULB
1. Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
2. Remove front side marker lamp bulb from the front side marker lamp bulb socket.
Disassembly and Assembly
INFOID:0000000012201788
DISASSEMBLY
1. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
2. Remove front turn signal lamp bulb from the front turn signal lamp bulb socket.
3. Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
4. Remove front side marker lamp bulb from the front side marker lamp bulb socket.
ASSEMBLY
Note the following item, and then assemble in the reverse order of disassembly.
CAUTION:
After installing the bulb, install the bulb socket securely for watertightness.
1.
Front combination lamp
2.
Front turn signal lamp bulb
3.
Front turn signal lamp bulb socket
4.
Front side marker lamp bulb
5.
Front side marker lamp bulb socket
: Vehicle front
Revision: November 2015
2016 JUKE
EXL-212
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
DAYTIME RUNNING LIGHT
DAYTIME RUNNING LIGHT
Exploded View
INFOID:0000000012201789
Removal and Installation
INFOID:0000000012201790
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-119, "Precautions for Removing Battery Terminal"
REMOVAL
1. Remove front bumper fascia lower. Refer to
EXT-17, "Removal and Installation"
.
2. Disconnect daytime running light harness connector.
3. Remove daytime running light mounting nuts.
4. Remove daytime running light from front bumper fascia lower.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000012201791
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-119, "Precautions for Removing Battery Terminal"
DAYTIME RUNNING LIGHT
CAUTION:
Replacement of a single part is not possible due to the adoption of LED. For replacement, replace day-
time running light as a set. Refer to
EXL-212, "Removal and Installation"
.
1.
Daytime running light
2.
Front bumper fascia assembly
3.
U nut
4
Harness connector assembly
N·m (kg-m, in-lb)
JMLIA3676GB
Revision: November 2015
2016 JUKE
FRONT FOG LAMP
EXL-213
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000012201792
Removal and Installation
INFOID:0000000012201793
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
EXL-119, "Precautions for Removing Battery Terminal"
REMOVAL
1. Remove front fender protector to make work space. Refer to
EXT-31, "Removal and Installation"
2. Disconnect front fog lamp harness connector.
3. Remove front fog lamp fixing screws, and then remove front fog lamp from front fog lamp bracket.
4. Remove front fog lamp bracket mounting bolt and fixing clips, and then remove front fog lamp bracket.
1.
Front bumper fascia assembly
2.
Front fog lamp bracket
3.
Front fog lamp bulb
4.
Front fog lamp
5.
U nut
: Vehicle front
: N·m (kg-m, in-lb)
JMLIA5401GB
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст