Nissan Juke (2016 year). Service Repair Manual — part 565
SEC-46
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORK FLOW
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES
>> GO TO 8.
NO
>> Check according to
GI-45, "Intermittent Incident"
.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO
>> Before returning the vehicle to the customer, always erase DTC.
Revision: November 2015
2016 JUKE
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
SEC-47
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ECM
ECM : Description
INFOID:0000000012202128
When replacing ECM, the following procedure must be performed. For details, refer to
.
PROGRAMMING OPERATION
NOTE:
After replacing with a blank ECM, programming is required to write ECM information. Be sure to follow the pro-
cedure to perform the programming.
ECM : Work Procedure
INFOID:0000000012202129
1.
CHECK ECM PART NUMBER
Check ECM part number to see whether it is blank ECM or not.
NOTE:
• Part number of blank ECM is 23703 -
×××××
.
• Check the part number when ordering ECM or with the one included in the label on the container box.
Is the ECM a blank ECM?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
SAVE ECM PART NUMBER
Read out the part number from the old ECM and save the number, following the programming instructions.
Refer to “CONSULT Operation Manual”.
NOTE:
• The ECM part number is saved in CONSULT.
• Even when ECM part number is not saved in CONSULT, go to 3.
>> GO TO 3.
3.
PERFORM ECM PROGRAMMING
After replacing ECM, perform the ECM programming. Refer to “CONSULT Operation Manual”.
NOTE:
• Refer to
EC-590, "Removal and Installation"
for replacement of ECM.
• During programming, maintain the following conditions:
- Ignition switch: ON
- Electric load: OFF
- Brake pedal: Not depressed
- Battery voltage: 12 – 13.5 V (Be sure to check the value of battery voltage by selecting “BATTERY VOLT” in
“Data monitor” of CONSULT.)
>> GO TO 5.
4.
REPLACE ECM
EC-590, "Removal and Installation"
>> GO TO 5.
5.
PERFORM INITIALIZATION OF NVIS (NATS) SYSTEM AND REGISTRATION OF ALL NVIS (NATS) IGNI-
TION KEY IDS
SEC-13, "NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS : System Description"
>> GO TO 6.
6.
PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
Revision: November 2015
2016 JUKE
SEC-48
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
>> GO TO 7.
7.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
>> GO TO 8.
8.
PERFORM IDLE AIR VOLUME LEARNING
.
>> GO TO 9.
9.
PERFORM G SENSOR CALIBRATION
>> END
BCM
BCM : Description
INFOID:0000000012202130
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replace-
ment. For details, refer to
SEC-48, "BCM : Work Procedure"
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, always perform “WRITE CONFIGURATION” with CONSULT. Or not doing so,
BCM control function does not operate normally.
• Complete the procedure of “WRITE CONFIGURATION” in order.
• Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
• If you set incorrect “WRITE CONFIGURATION”, incidents might occur.
NOTE:
When replacing BCM, perform the system initialization (NATS) (if equipped).
BCM : Work Procedure
INFOID:0000000012202131
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “READ CONFIGURATION” to save or print current vehicle specification. Refer to
.
NOTE:
If “READ CONFIGURATION” can not be used, use the “WRITE CONFIGURATION - Manual selection” after
replacing BCM.
>> GO TO 2.
2.
REPLACE BCM
Replace BCM. Refer to
BCS-94, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
Revision: November 2015
2016 JUKE
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
SEC-49
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
CONSULT Configuration
Perform “WRITE CONFIGURATION - Config file” or “WRITE CONFIGURATION - Manual selection” to write
vehicle specification. Refer to
>> GO TO 4.
4.
INITIALIZE BCM (NATS) (IF EQUIPPED)
Perform BCM initialization. (NATS)
>> WORK END
Revision: November 2015
2016 JUKE
SEC-50
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
P1610 LOCK MODE
DTC/CIRCUIT DIAGNOSIS
P1610 LOCK MODE
Description
INFOID:0000000012202132
ECM forcibly switches to the mode that inhibits engine start, when engine start operation is performed 5 times
or more while communication between ECM and BCM is not normal.
DTC Logic
INFOID:0000000012202133
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012202134
1.
CHECK ENGINE START FUNCTION
1. Check that DTC except for DTC P1610 is not detected.
If detected, erase the DTC after fixing.
2. Turn ignition switch OFF.
3. Depress brake pedal and contact the registered Intelligent Key backside to push-button ignition switch,
then wait 5 seconds.
4. Turn ignition switch ON.
5. Turn ignition switch OFF and wait 5 seconds.
6. Repeat steps 3 and 5 twice (a total of 3 times).
7. Check that engine can start.
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1610
LOCK MODE
When ECM detects a communication malfunction between
ECM and BCM 5 times or more.
—
Revision: November 2015
2016 JUKE
P1611 ID DISCORD, IMMU-ECM
SEC-51
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
P1611 ID DISCORD, IMMU-ECM
DTC Logic
INFOID:0000000012202135
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012202136
1.
PERFORM INITIALIZATION
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
Can the system be initialized and can the engine be started with registered Intelligent Key?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK SELF DIAGNOSTIC RESULT
1. Select “Self Diagnostic Result” mode of “ENGINE” using CONSULT.
2. Erase DTC.
3. Perform DTC CONFIRMATION PROCEDURE for DTC P1611. Refer to
.
Is DTC detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
Can the system be initialized and can the engine be started with registered Intelligent Key?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
REPLACE ECM
Replace ECM.
EC-590, "Removal and Installation"
.
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1611
ID DISCORD, IMMU-ECM
The ID verification results between BCM
and ECM are NG.
• BCM
• ECM
Revision: November 2015
2016 JUKE
SEC-52
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
P1612 CHAIN OF ECM-IMMU
P1612 CHAIN OF ECM-IMMU
DTC Logic
INFOID:0000000012202137
DTC DETECTION LOGIC
NOTE:
• If DTC P1612 is displayed with DTC U1000 (for BCM), first perform the trouble diagnosis for DTC U1000.
.
• If DTC P1612 is displayed with DTC U1010 (for BCM), first perform the trouble diagnosis for DTC U1010.
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in “Self Diagnostic Result” mode of “ENGINE” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012202138
1.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
Can the system be initialized and can the engine be started with registered Intelligent Key?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
REPLACE ECM
Replace ECM.
EC-590, "Removal and Installation"
.
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1612
CHAIN OF ECM-IMMU
Inactive communication between ECM
and BCM
• Harness or connectors
(The CAN communication line is open or
shorted.)
• BCM
• ECM
Revision: November 2015
2016 JUKE
B2192 ID DISCORD, IMMU-ECM
SEC-53
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2192 ID DISCORD, IMMU-ECM
DTC Logic
INFOID:0000000012202139
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012202140
1.
PERFORM INITIALIZATION
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
Can the system be initialized and can the engine be started with registered Intelligent Key?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK SELF DIAGNOSTIC RESULT
1. Select “Self Diagnostic Result” mode of “BCM” using CONSULT.
2. Erase DTC.
3. Perform DTC CONFIRMATION PROCEDURE for DTC B2192. Refer to
Is DTC detected?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT.
Can the system be initialized and can the engine be started with registered Intelligent Key?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
REPLACE ECM
Replace ECM.
EC-590, "Removal and Installation"
.
>> INSPECTION END
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2192
ID DISCORD BCM-ECM
The ID verification results between
BCM and ECM are NG.
• BCM
• ECM
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст