Nissan Juke (2016 year). Service Repair Manual — part 354
EXL-54
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
HEADLAMP (LO) CIRCUIT
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK HEADLAMP (LO) GROUND CIRCUIT
Check continuity between headlamp harness connector and ground.
Is the inspection result normal?
YES
>> Perform the xenon headlamp diagnosis. Refer to
.
NO
>> Repair or replace harness.
IPDM E/R
Headlamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E15
52
E55
4
Existed
LH
51
E54
Headlamp
—
Continuity
Connector
Terminal
RH
E55
2
Ground
Existed
LH
E54
Revision: November 2015
2016 JUKE
XENON HEADLAMP
EXL-55
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
XENON HEADLAMP
Diagnosis Procedure
INFOID:0000000012201641
1.
CHECK XENON BULB
Install the normal bulb to the applicable headlamp. Check that the headlamp (LO) is turned ON.
Is the headlamp (LO) turned ON?
YES
>> Replace the corresponding xenon bulb. Refer to
NO
>> GO TO 2.
2.
CHECK XENON HEADLAMP
Install the normal headlamp assembly to the applicable headlamp. Check that the headlamp (LO) is turned
ON.
Is the headlamp (LO) turned ON?
YES
>> Replace the corresponding headlamp assembly. Refer to
EXL-96, "Removal and Installation"
NO
>> Xenon headlamp is normal.
Revision: November 2015
2016 JUKE
EXL-56
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
PARKING LAMP CIRCUIT
PARKING LAMP CIRCUIT
Component Function Check
INFOID:0000000012201642
1.
CHECK TAIL LAMP OPERATION
Check that the tail lamp is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check tail lamp circuit. Refer to
EXL-60, "Component Function Check"
2.
CHECK PARKING LAMP OPERATION
With CONSULT
1. Turn ignition switch ON.
2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.
3. With operating the test items, check that the parking lamp is turned ON.
Without CONSULT
1. Start IPDM E/R auto active test. Refer to
PCS-12, "Diagnosis Description"
2. Check that the parking lamp is turned ON.
Is the inspection result normal?
YES
>> Parking lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012201643
1.
CHECK PARKING LAMP POWER SUPPLY
With CONSULT
1. Turn ignition switch ON.
2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.
3. With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
2.
CHECK PARKING LAMP POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and parking lamp connector.
3. Check continuity between IPDM E/R harness connector and parking lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
TAIL
: Parking lamp ON
Off
: Parking lamp OFF
+
-
Test item
Voltage
IPDM E/R
Connector
Terminal
E14
43
Ground
EXTERNAL
LAMPS
TAIL
9 – 16 V
Off
0 – 1 V
IPDM E/R
Parking lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E14
43
E44
1
Existed
LH
E28
Revision: November 2015
2016 JUKE
PARKING LAMP CIRCUIT
EXL-57
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NO
>> Repair or replace harness.
3.
CHECK PARKING LAMP GROUND CIRCUIT
Check continuity between parking lamp harness connector and ground.
Is the inspection result normal?
YES
>> Replace the corresponding front combination lamp. Refer to
EXL-100, "Removal and Installation"
.
NO
>> Repair or replace harness.
Parking lamp
—
Continuity
Connector
Terminal
RH
E44
2
Ground
Existed
LH
E28
Revision: November 2015
2016 JUKE
EXL-58
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
FRONT SIDE MARKER LAMP CIRCUIT
FRONT SIDE MARKER LAMP CIRCUIT
Component Function Check
INFOID:0000000012201644
1.
CHECK PARKING LAMP OPERATION
Check that the parking lamp is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check parking lamp circuit. Refer to
EXL-56, "Component Function Check"
2.
CHECK FRONT SIDE MARKER LAMP OPERATION
With CONSULT
1. Turn ignition switch ON.
2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.
3. With operating the test items, check that the front side marker lamp is turned ON.
Without CONSULT
1. Start IPDM E/R auto active test. Refer to
PCS-12, "Diagnosis Description"
2. Check that the front side marker lamp is turned ON.
Is the inspection result normal?
YES
>> Front side marker lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012201645
1.
CHECK FRONT SIDE MARKER LAMP POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and front side marker lamp connector.
3. Check continuity between IPDM E/R harness connector and front side marker lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK FRONT SIDE MARKER LAMP GROUND CIRCUIT
Check continuity between front side marker lamp harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK FRONT SIDE MARKER LAMP BULB
Check the applicable front side marker lamp bulb.
TAIL
: Front side marker lamp ON
Off
: Front side marker lamp OFF
IPDM E/R
Front side marker lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E14
43
E32
1
Existed
LH
E31
Front side marker lamp
—
Continuity
Connector
Terminal
RH
E32
2
Ground
Existed
LH
E31
Revision: November 2015
2016 JUKE
FRONT SIDE MARKER LAMP CIRCUIT
EXL-59
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> Check the corresponding front side marker lamp bulb socket. Repair or replace if necessary.
NO
>> Replace the corresponding front side marker lamp bulb. Refer to
Revision: November 2015
2016 JUKE
EXL-60
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
TAIL LAMP CIRCUIT
TAIL LAMP CIRCUIT
Component Function Check
INFOID:0000000012201646
1.
CHECK TAIL LAMP OPERATION
With CONSULT
1. Turn ignition switch ON.
2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.
3. With operating the test items, check that the tail lamp is turned ON.
Without CONSULT
1. Start IPDM E/R auto active test. Refer to
PCS-12, "Diagnosis Description"
2. Check that the tail lamp is turned ON.
Is the inspection result normal?
YES
>> Tail lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012201647
1.
CHECK FUSE
1. Turn ignition switch OFF.
2. Check that the following fuse is not blown (open).
Is the fuse blown (open)?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown (open).
NO
>> GO TO 2.
2.
CHECK TAIL LAMP POWER SUPPLY
With CONSULT
1. Turn ignition switch ON.
2. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.
3. With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
3.
CHECK TAIL LAMP POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
TAIL
: Tail lamp ON
Off
: Tail lamp OFF
Unit
Location
Fuse No.
Capacity
• Parking lamp RH
• Parking lamp LH
• Front side marker lamp RH
• Front side marker lamp LH
• Tail lamp RH
• Tail lamp LH
• License plate lamp RH
• License plate lamp LH
IPDM E/R
#47
10 A
+
-
Test item
Voltage
IPDM E/R
Connector
Terminal
E14
44
Ground
EXTERNAL
LAMPS
TAIL
9 – 16 V
Off
0 – 1 V
Revision: November 2015
2016 JUKE
TAIL LAMP CIRCUIT
EXL-61
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2. Disconnect IPDM E/R connector and rear combination lamp connector.
3. Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TAIL LAMP GROUND CIRCUIT
Check continuity between rear combination lamp harness connector and ground.
Is the inspection result normal?
YES-1 >> Stop lamp / tail lamp (Bulb side): GO TO 5.
YES-2 >> Tail lamp (LED side): Check the corresponding tail lamp harness, and if check result is normal,
replace the corresponding rear combination lamp. Refer to
EXL-109, "Removal and Installation"
NO
>> Repair or replace harness.
5.
CHECK STOP LAMP / TAIL LAMP BULB
Check the applicable stop lamp / tail lamp bulb.
Is the inspection result normal?
YES
>> Check the corresponding stop lamp / tail lamp bulb socket and harness. Repair or replace if nec-
essary.
NO
>> Repair or replace the corresponding stop lamp / tail lamp bulb. Refer to
.
IPDM E/R
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E14
44
B59
2
Existed
LH
B80
Rear combination lamp
—
Continuity
Connector
Terminal
RH
B59
3
Ground
Existed
LH
B80
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст