Nissan Juke (2016 year). Service Repair Manual — part 439
COMPRESSOR DOES NOT OPERATE
HAC-149
< SYMPTOM DIAGNOSIS >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
COMPRESSOR DOES NOT OPERATE
Description
INFOID:0000000012200142
SYMPTOM
Compressor does not operate.
Diagnosis Procedure
INFOID:0000000012200143
NOTE:
• Perform self-diagnosis with CONSULT before performing symptom diagnosis. If any malfunction result or
DTC is detected, perform the corresponding diagnosis.
• Check that refrigerant is enclosed in cooler cycle normally. If the refrigerant amount is shortage from proper
amount, perform the inspection of refrigerant leakage
1.
CHECK A/C INDICATOR
1. Turn ignition switch ON.
2. Operate blower motor.
3. Check that A/C indicator is turned ON/OFF when operating A/C switch.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
CHECK MAGNET CLUTCH OPERATION
Check magnet clutch. Refer to
HAC-144, "Component Function Check"
Does it operate normally?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CHECK REFRIGERANT PRESSURE SENSOR
Check refrigerant pressure sensor. Refer to
EC-568, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CHECK BCM OUTPUT SIGNAL
With CONSULT
1. Select “DATA MONITOR” mode of “ECM” using CONSULT.
2. Select “AIR COND SIG” and “HEATER FAN SW”, and check status under the following conditions.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
.
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
5.
CHECK A/C SWITCH
Check A/C switch. Refer to
HAC-130, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CHECK BLOWER FAN ON SIGNAL
Monitor item
Condition
Status
AIR COND SIG
A/C switch
OFF (A/C indicator: OFF)
Off
ON (A/C indicator: ON)
On
HEATER FAN SW
Blower motor
OFF
Off
ON
On
Revision: November 2015
2016 JUKE
HAC-150
< SYMPTOM DIAGNOSIS >
[MANUAL AIR CONDITIONING]
COMPRESSOR DOES NOT OPERATE
Check blower fan ON signal. Refer to
HAC-132, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace the malfunctioning parts
7.
CHECK THERMO CONTROL AMP.
Check thermo control amp. Refer to
HAC-134, "Component Function Check"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace the malfunctioning parts
Revision: November 2015
2016 JUKE
A/C CONTROL
HAC-151
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
REMOVAL AND INSTALLATION
A/C CONTROL
Exploded View
INFOID:0000000012200144
Removal and Installation
INFOID:0000000012200145
REMOVAL
1. Remove A/C finisher. Refer to
IP-13, "Removal and Installation"
.
2. Remove fixing screws (A) and fixing pawls, and then remove A/
C control.
3. Disconnect door cable and harness connector from A/C control.
INSTALLATION
Install in the reverse order of removal.
1.
Air mix door cable
2.
Intake door cable
3.
A/C control
4.
Mode door cable
5.
Intake door lever knob
A.
To air mix door link
B.
To intake door link
C.
To mode door link
JMIIA0899ZZ
: Pawl
JMIIA0900ZZ
Revision: November 2015
2016 JUKE
HAC-152
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
THERMO CONTROL AMPLIFIER
THERMO CONTROL AMPLIFIER
Removal and Installation
INFOID:0000000012200146
REMOVAL
1. Remove evaporator. Refer to
HA-46, "EVAPORATOR : Removal and Installation"
2. Disconnect thermo control amp. from evaporator.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-ring with new one. Then apply compressor oil to them when installing.
• When install the thermo control amp., set the same position before replacement.
• When remove the thermo control amp., never turn the bracket which is equipped the top of the
thermo control amp.
• Check for the leakages when recharging refrigerant. Refer to
Revision: November 2015
2016 JUKE
REFRIGERANT PRESSURE SENSOR
HAC-153
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
REFRIGERANT PRESSURE SENSOR
Exploded View
INFOID:0000000012200147
.
Removal and Installation
INFOID:0000000012200148
REMOVAL
HA-38, "REFRIGERANT PRESSURE SENSOR : Removal and Installation"
.
INSTALLATION
Install in the reverse order of removal.
Revision: November 2015
2016 JUKE
HAC-154
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
BLOWER FAN RESISTOR
BLOWER FAN RESISTOR
Exploded View
INFOID:0000000012200149
• *1: Manual air conditioning
• *2: Automatic air conditioning
Removal and Installation
INFOID:0000000012200150
REMOVAL
1. Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2. Disconnect blower fan resistor harness connector.
3. Remove fixing screws, and then remove blower fan resistor from A/C unit assembly.
INSTALLATION
Install in the reverse order of removal.
1.
A/C unit assembly
2.
Blower fan resistor*
1
3.
Sub harness*
1
4.
Power transistor*
2
5.
Sub harness*
2
6.
Blower motor
JPIIA1549ZZ
Revision: November 2015
2016 JUKE
DOOR CABLE
HAC-155
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
DOOR CABLE
Exploded View
INFOID:0000000012200151
LEFT SIDE
RIGHT SIDE
1.
A/C unit assembly
2.
Intake door lever
3.
Intake door link
4.
Intake door cable
5.
Air mix door cable
6.
Upper air mix door rod
7.
Upper air mix door lever
8.
Lower air mix door lever
9.
Lower air mix door rod
10. Air mix door link
A.
To A/C control
JPIIA1559ZZ
Revision: November 2015
2016 JUKE
HAC-156
< REMOVAL AND INSTALLATION >
[MANUAL AIR CONDITIONING]
DOOR CABLE
INTAKE DOOR CABLE
INTAKE DOOR CABLE : Removal and Installation
INFOID:0000000012200152
REMOVAL
1. Disconnect intake door cable from A/C control. Refer to
.
2. Remove instrument lower panel LH. Refer to
IP-13, "Removal and Installation"
.
3. Disconnect intake door cable from A/C unit assembly as shown
by the arrow in the figure, and then remove intake door cable.
INSTALLATION
Install in the reverse order of removal.
MODE DOOR CABLE
1.
A/C unit assembly
2.
Main link
3.
Sub defroster door link
4.
Sub defroster door rod
5.
Mode door cable
6.
Plate
7.
Mode link
8.
Sub defroster door lever
9.
Center ventilator and defroster door link
10. Plate
11. Center ventilator and defroster door rod
12. Center ventilator and defroster door lever
A.
To A/C control
JPIIA1560ZZ
JMIIA0901ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст