Nissan Juke (2016 year). Service Repair Manual — part 219
ON BOARD REFUELING VAPOR RECOVERY (ORVR)
EC-567
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace refueling EVAP vapor cut valve with fuel tank .Refer to
Component Inspection (Drain filter)
INFOID:0000000012198112
1.
CHECK DRAIN FILTER
1. Check visually for insect nests in the drain filter air inlet.
2. Check visually for cracks or flaws in the appearance.
3. Check visually for cracks or flaws in the hose.
4. Blow air into port A and check that it flows freely out of port B.
5. Block port B.
6. Blow air into port A and check that there is no leakage.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace drain filter.
1.
Filler tube
2.
Recirculation line
3.
EVAP/ORVR line
4.
Vacuum/pressure handy pump
5.
Fuel tank
JMBIA2315ZZ
PBIB3641E
Revision: November 2015
2016 JUKE
EC-568
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
REFRIGERANT PRESSURE SENSOR
REFRIGERANT PRESSURE SENSOR
Component Function Check
INFOID:0000000012198113
1.
CHECK REFRIGERANT PRESSURE SENSOR OVERALL FUNCTION
1. Start engine and warm it up to normal operating temperature.
2. Turn A/C switch and blower fan switch ON.
3. Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000012198114
1.
CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY
1. Turn ignition OFF.
2. Disconnect refrigerant pressure sensor harness connector.
3. Turn ignition switch ON.
4. Check the voltage between refrigerant pressure sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK REFRIGERANT PRESSURE SENSOR POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between refrigerant pressure sensor harness connector and ECM harness connec-
tor.
4. Also check harness for short to ground.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.
CHECK REFRIGERANT PRESSURE SENSOR GROUND
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between refrigerant pressure sensor harness connector and ECM harness connec-
tor.
ECM
Voltage
Connector
+
−
Terminal
F25
19
12
1.0 - 4.0V
+
−
Voltage
(Approx.)
Refrigerant pressure sensor
Connector
Terminal
E49
3
Ground
5 V
+
−
Continuity
Refrigerant pressure sensor
ECM
Connector
Terminal
Connector
Terminal
E49
3
F25
23
Existed
Revision: November 2015
2016 JUKE
REFRIGERANT PRESSURE SENSOR
EC-569
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4. Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK REFRIGERANT PRESSURE SENSOR INPUT SIGNAL CIRCUIT
1. Check the continuity between ECM harness connector and refrigerant pressure sensor harness connec-
tor.
2. Also check harness for short to ground and to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.
CHECK INTERMITTENT INCIDENT.
Perform
GI-45, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace refrigerant pressure sensor. Refer to
.
NO
>> Repair or replace error-detected parts.
+
−
Continuity
Refrigerant pressure sensor
ECM
Connector
Terminal
Connector
Terminal
E49
1
F25
12
Existed
+
−
Continuity
Refrigerant pressure sensor
ECM
Connector
Terminal
Connector
Terminal
E49
2
F25
19
Existed
Revision: November 2015
2016 JUKE
EC-570
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
BRAKE PEDAL POSITION SWITCH
BRAKE PEDAL POSITION SWITCH
Component Function Check
INFOID:0000000012198115
1.
CHECK BRAKE PEDAL POSITION SWITCH FUNCTION
With CONSULT
1. Turn ignition switch ON.
2. Select “BRAKE SW1” in “DATA MONITOR” mode of “ENGINE” using CONSULT.
3. Check “BRAKE SW1” indication as per the following conditions.
Without CONSULT
1. Turn ignition switch ON.
2. Check the voltage between ECM harness connector terminals as per the following.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000012198116
1.
CHECK BRAKE PEDAL POSITION SWITCH POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect brake pedal position switch harness connector.
3. Turn ignition switch ON.
4. Check the voltage between brake pedal position switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform the trouble diagnosis for power supply circuit.
2.
CHECK BRAKE PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between brake pedal position switch harness connector and ECM harness connec-
tor.
Monitor item
Condition
Indication
BRAKE SW1
Brake pedal
Slightly depressed
OFF
Fully released
ON
ECM
Condition
Voltage
(Approx.)
Connector
+
–
Terminal
E18
116
127
Brake pedal
Slightly depressed
0 V
Fully released
Battery voltage
+
−
Voltage
Brake pedal position switch
Connector
Terminal
E112
1
Ground
Battery voltage
+
−
Continuity
Brake pedal position switch
ECM
Connector
Terminal
Connector
Terminal
E112
2
E18
116
Existed
Revision: November 2015
2016 JUKE
BRAKE PEDAL POSITION SWITCH
EC-571
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK BRAKE PEDAL POSITION SWITCH
Check the brake pedal position switch. Refer to
EC-571, "Component Inspection (Brake Pedal Position
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace brake pedal position switch. Refer to
Component Inspection (Brake Pedal Position Switch)
INFOID:0000000012198117
1.
CHECK BRAKE PEDAL POSITION SWITCH-I
1. Turn ignition switch OFF.
2. Disconnect brake pedal position harness connector.
3. Check the continuity between brake pedal position switch terminals as per the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK BRAKE PEDAL POSITION SWITCH-II
1. Adjust brake pedal position switch installation. Refer to
BR-9, "Inspection and Adjustment"
.
2. Check the continuity between brake pedal position switch terminals as per the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace brake pedal position switch. Refer to
Brake pedal position switch
Condition
Continuity
+
−
Terminals
1
2
Brake pedal
Fully released
Existed
Slightly de-
pressed
Not existed
Brake pedal position switch
Condition
Continuity
+
−
Terminals
1
2
Brake pedal
Fully released
Existed
Slightly de-
pressed
Not existed
Revision: November 2015
2016 JUKE
EC-572
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
CLUTCH PEDAL POSITION SWITCH
CLUTCH PEDAL POSITION SWITCH
Component Function Check
INFOID:0000000012198118
1.
CHECK FOR CLUTCH PEDAL POSITION SWITCH FUNCTION
1. Turn ignition switch ON.
2. Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000012198119
1.
CHECK CLUTCH PEDAL POSITION INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect clutch pedal position switch harness connector.
3. Turn ignition switch ON.
4. Check the voltage between clutch pedal position switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK CLUTCH PEDAL POSITION SWITCH INPUT SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connectors.
3. Check the continuity between clutch pedal position switch harness connector and ECM harness connec-
tor.
4. Also check harness for short to ground and to power.
Is the inspection result normal?
YES
>> Perform the trouble diagnosis for power supply circuit.
NO
>> Repair or replace error-detected parts.
3.
CHECK CLUTCH PEDAL POSITION SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connectors.
3. Check the continuity between clutch pedal position switch harness connector and ground
ECM
Condition
Voltage
(Approx.)
Connector
+
−
Terminal
E18
108
127
Clutch pedal
Slightly depressed
Battery voltage
Fully released
0V
+
−
Voltage
Clutch pedal position switch
Connector
Terminal
E113
1
Ground
Battery voltage
+
−
Continuity
Clutch pedal position switch
ECM
Connector
Terminal
Connector
Terminal
E113
1
E18
108
Existed
Revision: November 2015
2016 JUKE
CLUTCH PEDAL POSITION SWITCH
EC-573
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4. Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK CLUTCH PEDAL POSITION SWITCH
Check the clutch pedal position switch. Refer to
EC-573, "Component Inspection"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
NO
>> Replace clutch pedal position switch. Refer to
.
Component Inspection
INFOID:0000000012198120
1.
CHECK CLUTCH PEDAL POSITION SWITCH-I
1. Turn ignition switch OFF.
2. Disconnect clutch pedal position switch harness connector.
3. Check the continuity between clutch pedal position switch terminals as per the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK CLUTCH PEDAL POSITION SWITCH-II
1. Adjust clutch pedal position switch installation. Refer to
CL-12, "Inspection and Adjustment"
.
2. Check the continuity between clutch pedal position switch terminals as per the following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace clutch pedal position switch. Refer to
.
+
−
Continuity
Clutch pedal position switch
Connector
Terminal
E113
2
Ground
Existed
Clutch pedal position switch
Condition
Continuity
+
−
Terminal
1
2
Clutch pedal
Fully released
Existed
Slightly depressed
Not existed
Clutch pedal position switch
Condition
Continuity
+
−
Terminal
1
2
Clutch pedal
Fully released
Existed
Slightly depressed
Not existed
Revision: November 2015
2016 JUKE
EC-574
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
INFORMATION DISPLAY (ASCD)
INFORMATION DISPLAY (ASCD)
Component Function Check
INFOID:0000000012198121
1.
CHECK INFORMATION DISPLAY
1. Start engine.
2. Press ASCD MAIN switch on ASCD steering switch.
3. Drive the vehicle at more than 40 km/h (25 MPH).
CAUTION:
Always drive vehicle at a safe speed.
4. Press SET/
−
switch.
5. Check that the reading of the speedometer shows the same value as the set speed indicated in the infor-
mation display while driving the vehicle on a flat road.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000012198122
1.
CHECK DTC
Check that DTC UXXXX, P0500 or P1574 is not displayed.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1 >> Perform trouble diagnosis for DTC UXXXX.
NO-2 >> Perform trouble diagnosis for DTC P0500. Refer to
EC-397, "EXCEPT FOR M/T MODELS : DTC
.
NO-3 >> Perform trouble diagnosis for DTC P1574. Refer to
.
2.
CHECK DTC WITH COMBINATION METER
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Perform trouble diagnosis for DTC indicated.
3.
CHECK INTERMITTENT INCIDENT
Perform
GI-45, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-64, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст