Nissan Juke (2016 year). Service Repair Manual — part 33
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
1
: For models without auto light system, this item cannot be used.
*
2
: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Service item
Setting item
Setting
CUSTOM A/LIGHT SETTING*
1
MODE1*
2
Normal
MODE2
More sensitive setting than normal setting (Turns ON earlier than normal operation)
MODE3
More sensitive setting than MODE2 (Turns ON earlier than MODE2)
MODE4
Less sensitive setting than normal setting (Turns ON later than normal operation)
BATTERY SAVER SET
On*
2
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET*
1
MODE1*
2
45 sec.
Sets delay timer function timer operation time.
(All doors closed)
MODE2
Without the function
MODE3
30 sec.
MODE4
60 sec.
MODE5
90 sec.
MODE6
120 sec.
MODE7
150 sec.
MODE8
180 sec.
HEAD LIGHT TIMER
MODE1
10 sec.
Sets follow me home function activating time
MODE2*
2
30 sec.
AUTO LIGHT LOGIC SET*
1
MODE1*
2
With twilight ON custom & with wiper INT, LO and HI
MODE2
With twilight ON custom & with wiper LO and HI
MODE3
With twilight ON custom & without
MODE4
Without twilight ON custom & with wiper INT, LO and HI
MODE5
Without twilight ON custom & with wiper LO and HI
MODE6
Without twilight ON custom & without
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
ENGINE STATE
[STOP/STALL/CRANK/RUN]
Indicates [STOP/STALL/CRANK/RUN] condition of engine states
VEH SPEED 1
[km/h]
Display the vehicle speed signal received from combination meter by numerical value [km/h]
Revision: November 2015
2016 JUKE
BCS-22
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*
1
: For models without auto light system, this item cannot be monitored.
*
2
: For models without front fog lamp, this item cannot be monitored.
ACTIVE TEST
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW 1
[On/Off]
HEAD LAMP SW 2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW*
1
[On/Off]
FR FOG SW*
2
[On/Off]
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
[On/Off]
Indicated [On/Off] condition of back door switch
OPTI SEN (DTCT)
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)
[V]
The value of outside brightness voltage filtered by BCM
OPTICAL SENSOR
[On/Off/NG]
NOTE:
This item cannot be monitored
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
• Transmits the position light request signal to IPDM E/R via CAN communication to
turn the parking, license plate and tail lamps ON
• Transmits the position light request signal to combination meter via CAN commu-
nication to turn the position lamp indicator lamp ON
Off
Stops the position light request signal transmission
HEAD LAMP
HI
• Transmits the high beam request signal to IPDM E/R via CAN communication to
turn the headlamp (HI) ON
• Transmits the high beam request signal to combination meter via CAN communi-
cation to turn the high beam indicator lamp ON
Low
Transmits the low beam request signal to IPDM E/R via CAN communication to turn
the headlamp (LO) ON
Off
Stops the high beam request signal and low beam request signal transmission
Revision: November 2015
2016 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-23
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
1
: For models without front fog lamp and except for NISMO models with daytime running light system, this
item cannot be tested.
*
2
: For models without daytime running light system and NISMO models with daytime running light system,
this item cannot be tested.
HEADLAMP : CONSULT Function (BCM - HEAD LAMP) (HALOGEN TYPE)
INFOID:0000000012965021
WORK SUPPORT
*
1
: For models without auto light system, this item cannot be used.
FR FOG LAMP*
1
On
• Transmits the front fog light request signal to IPDM E/R via CAN communication
to turn the front fog lamp ON (With front fog lamp)
• Transmits the daytime running light request signal to IPDM E/R via CAN commu-
nication to turn the daytime running light ON (NISMO models with daytime running
light system)
Off
• Stops the front fog light request signal transmission (With front fog lamp)
• Stops the front fog light request signal transmission (NISMO models with daytime
running light system)
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal to IPDM E/R via CAN communi-
cation to turn the headlamp (HI) ON [Headlamp (HI) at approximately half illumina-
tion]
Off
Stops the daytime running light request signal transmission
ILL DIM SIGNAL
On
NOTE:
This item cannot be tested
Off
Test item
Operation
Description
Service item
Setting item
Setting
CUSTOM A/LIGHT SETTING*
1
MODE1*
2
Normal
MODE2
More sensitive setting than normal setting (Turns ON earlier than normal operation)
MODE3
More sensitive setting than MODE2 (Turns ON earlier than MODE2)
MODE4
Less sensitive setting than normal setting (Turns ON later than normal operation)
BATTERY SAVER SET
On*
2
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET*
1
MODE1*
2
45 sec.
Sets delay timer function timer operation time.
(All doors closed)
MODE2
Without the function
MODE3
30 sec.
MODE4
60 sec.
MODE5
90 sec.
MODE6
120 sec.
MODE7
150 sec.
MODE8
180 sec.
HEAD LIGHT TIMER
MODE1
10 sec.
Sets follow me home function activating time
MODE2*
2
30 sec.
AUTO LIGHT LOGIC SET*
1
MODE1*
2
With twilight ON custom & with wiper INT, LO and HI
MODE2
With twilight ON custom & with wiper LO and HI
MODE3
With twilight ON custom & without
MODE4
Without twilight ON custom & with wiper INT, LO and HI
MODE5
Without twilight ON custom & with wiper LO and HI
MODE6
Without twilight ON custom & without
Revision: November 2015
2016 JUKE
BCS-24
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*
2
: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
*
1
: For models without auto light system, this item cannot be monitored.
*
2
: For models without front fog lamp, this item cannot be monitored.
ACTIVE TEST
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
ENGINE STATE
[STOP/STALL/CRANK/RUN]
Indicates [STOP/STALL/CRANK/RUN] condition of engine states
VEH SPEED 1
[km/h]
Display the vehicle speed signal received from combination meter by numerical value [km/h]
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW 1
[On/Off]
HEAD LAMP SW 2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW*
1
[On/Off]
FR FOG SW*
2
[On/Off]
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
[On/Off]
Indicated [On/Off] condition of back door switch
OPTI SEN (DTCT)
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)
[V]
The value of outside brightness voltage filtered by BCM
OPTICAL SENSOR
[On/Off/NG]
NOTE:
This item cannot be monitored
Revision: November 2015
2016 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-25
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*
1
: For models without front fog lamp and except for NISMO models with daytime running light system, this
item cannot be tested.
*
2
: For models without daytime running light system and NISMO models with daytime running light system,
this item cannot be tested.
WIPER
WIPER : CONSULT Function - WIPER
INFOID:0000000012965033
WORK SUPPORT
*:Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Operation
Description
TAIL LAMP
On
• Transmits the position light request signal to IPDM E/R via CAN communication to
turn the parking, license plate and tail lamps ON
• Transmits the position light request signal to combination meter via CAN commu-
nication to turn the position lamp indicator lamp ON
Off
Stops the position light request signal transmission
HEAD LAMP
HI
• Transmits the high beam request signal to IPDM E/R via CAN communication to
turn the headlamp (HI) ON
• Transmits the high beam request signal to combination meter via CAN communi-
cation to turn the high beam indicator lamp ON
Low
Transmits the low beam request signal to IPDM E/R via CAN communication to turn
the headlamp (LO) ON
Off
Stops the high beam request signal and low beam request signal transmission
FR FOG LAMP*
1
On
• Transmits the front fog light request signal to IPDM E/R via CAN communication
to turn the front fog lamp ON (With front fog lamp)
• Transmits the daytime running light request signal to IPDM E/R via CAN commu-
nication to turn the daytime running light ON (NISMO models with daytime running
light system)
Off
• Stops the front fog light request signal transmission (With front fog lamp)
• Stops the front fog light request signal transmission (NISMO models with daytime
running light system)
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal to IPDM E/R via CAN communi-
cation to turn the headlamp (HI) ON [Headlamp (HI) at approximately half illumina-
tion]
Off
Stops the daytime running light request signal transmission
ILL DIM SIGNAL
On
NOTE:
This item cannot be tested
Off
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Revision: November 2015
2016 JUKE
BCS-26
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER) (XENON TYPE)
INFOID:0000000012965029
WORK SUPPORT
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication
FR WIPER HI
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
FR WIPER LOW
[Off/On]
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP
[Off/On]
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
communication.
INT VOLUME
[1
−
7]
Status of each switch judged by BCM using the combination switch reading function
RR WIPER ON
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
RR WIPER INT
[Off/On]
RR WASHER SW
[Off/On]
RR WIPER STOP
[Off/On]
Rear wiper motor (stop position) status input from the rear wiper motor
RAIN SENSOR
[Off/LOW/HIGH/SPLASH/NG]
NOTE:
This item is displayed, but cannot be monitored.
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R via CAN communication to op-
erate the front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R via CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R via CAN communication to
operate the front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
On
Output the voltage to operate the rear wiper motor.
Off
Stops the voltage to stop the rear wiper motor.
Revision: November 2015
2016 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-27
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
*: For models without panic alarm function, this item cannot be used.
ACTIVE TEST
FLASHER : CONSULT Function (BCM - FLASHER) (HALOGEN TYPE)
INFOID:0000000012965030
WORK SUPPORT
Service item
Setting item
Setting
HAZARD ANSWER BACK
Lock
Only
With locking only
Sets the hazard warning lamp answer back function when
the door is lock/unlock with the door request switch and In-
telligent Key
Unlock
Only
With unlocking only
Lock/
Unlock*
With locking/unlocking
Off
Without the function
Monitor item
[Unit]
Description
REQ SW -DR
[On/Off]
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
[On/Off]
Indicates [On/Off] condition of door request switch (passenger side)
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-PANIC*
[On/Off]
Indicates [On/Off] condition of PANIC button of Intelligent Key
Test item
Operation
Description
FLASHER
RH
• Outputs voltage to turn the right side turn signal lamps ON
• Transmits the turn indicator signal to combination meter via CAN communication
to turn the turn signal indicator lamp (RH) ON
LH
• Outputs voltage to turn the left side turn signal lamps ON
• Transmits the turn indicator signal to combination meter via CAN communication
to turn the turn signal indicator lamp (LH) ON
Off
• Stops the voltage to turn the turn signal lamps OFF
• Stops the turn indicator signal transmission
Revision: November 2015
2016 JUKE
BCS-28
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
*: For models without panic alarm function, this item cannot be used.
ACTIVE TEST
AIR CONDITIONER
AIR CONDITIONER : CONSULT Function (BCM - AIR CONDITIONER) (Automatic A/
C)
INFOID:0000000012965035
DATA MONITOR
Service item
Setting item
Setting
HAZARD ANSWER BACK
Lock
Only
With locking only
Sets the hazard warning lamp answer back function when
the door is lock/unlock with the door request switch and In-
telligent Key
Unlock
Only
With unlocking only
Lock/
Unlock*
With locking/unlocking
Off
Without the function
Monitor item
[Unit]
Description
REQ SW -DR
[On/Off]
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
[On/Off]
Indicates [On/Off] condition of door request switch (passenger side)
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-PANIC*
[On/Off]
Indicates [On/Off] condition of PANIC button of Intelligent Key
Test item
Operation
Description
FLASHER
RH
• Outputs voltage to turn the right side turn signal lamps ON
• Transmits the turn indicator signal to combination meter via CAN communication
to turn the turn signal indicator lamp (RH) ON
LH
• Outputs voltage to turn the left side turn signal lamps ON
• Transmits the turn indicator signal to combination meter via CAN communication
to turn the turn signal indicator lamp (LH) ON
Off
• Stops the voltage to turn the turn signal lamps OFF
• Stops the turn indicator signal transmission
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст