Nissan Juke (2016 year). Service Repair Manual — part 402
FSU-16
< REMOVAL AND INSTALLATION >
FRONT STABILIZER
• Install stabilizer clamp and stabilizer bush with notch (A) and slit
(B) faced forward of the vehicle (
).
• To install stabilizer clamp mounting bolt, follow the tightening
method and the numerical order shown below:
• To install stabilizer connecting rod (1), tighten the mounting nut
with the hexagonal part (A) on the stabilizer connecting rod side
fixed.
• Perform final tightening of bolts and nuts at the vehicle installation
position (rubber bushing), under unladen conditions with tires on
level ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000012199126
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel alignment. Refer to
.
2. Adjust neutral position of steering angle sensor. Refer to
.
JPEIA0058ZZ
Manual tightening
: 1
Temporary tightening
: 2
→
3
Final tightening (Specified torque)
: 4
→
5
: Vehicle front
JPEIA0245GB
JPEIA0252ZZ
Revision: November 2015
2016 JUKE
FRONT SUSPENSION MEMBER
FSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
FRONT SUSPENSION MEMBER
Exploded View
INFOID:0000000012199127
Removal and Installation
INFOID:0000000012199128
REMOVAL
1. Separate intermediate shaft from steering gear assembly. Refer to
ST-14, "Removal and Installation"
.
2. Remove tires with power tool. Refer to
WT-39, "Removal and Installation"
.
3. Remove front under cover.
4. Separate stabilizer connecting rod from strut assembly. Refer to
FSU-15, "Removal and Installation"
5. Separate steering outer socket from steering knuckle. Refer to
ST-17, "Removal and Installation"
.
6. Separate transverse link from steering knuckle. Refer to
(NISMO),
(EXCEPT NISMO).
7. Remove rear torque rod.
• 2WD: Refer to
EM-64, "2WD : Removal and Installation"
.
• AWD: Refer to
EM-68, "AWD : Removal and Installation"
8. Set suitable jack under front suspension member.
CAUTION:
Check the stable condition when using a jack.
9. Remove member stay and rebound stopper.
10. Remove suspension member mounting bolts, insulator, and rebound stopper rubber.
11. Gradually lower the jack to remove front suspension member from vehicle body.
CAUTION:
Operate while checking that jack supporting status is stable.
NOTE:
Remove it with each component parts.
12. Remove component parts from front suspension member.
13. Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
1.
Front suspension member
2.
Rebound stopper rubber
3.
Insulator
4.
Member stay
5.
Rebound stopper
: N·m (kg-m, ft-lb)
JPEIA0271GB
Revision: November 2015
2016 JUKE
FSU-18
< REMOVAL AND INSTALLATION >
FRONT SUSPENSION MEMBER
• To install rebound stopper (1), insert it with the protrusion aligned
with the hole of member stay (2).
• To install member stay and mounting bolts of front suspension
member, temporarily tighten the bolts before tightening to the
specified torque, referring to the tightening method and the numer-
ical order shown below:
• Perform final tightening of bolts and nuts at the vehicle installation
position (rubber bushing), under unladen conditions with tires on level ground.
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000012199129
INSPECTION AFTER REMOVAL
Check front suspension member for cracks, wear or damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1. Check wheel sensor harness for proper connector. Refer to
BRC-147, "FRONT WHEEL SENSOR :
.
2. Check wheel alignment. Refer to
.
3. Adjust neutral position of steering angle sensor. Refer to
.
JPEIA0248ZZ
Temporary tightening
: 1
→
2
Final tightening
(Specified torque)
: 3
→
4
→
5
→
6
→
7
→
8
→
9
→
10
→
11
→
12
: Vehicle front
JPEIA0249GB
Revision: November 2015
2016 JUKE
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-19
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000012199130
Measure value under unladen*
2
conditions.
*1: A difference when assuming the left side a standard.
*2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000012199131
Wheelarch Height
INFOID:0000000012199132
FOR USA MODELS
EXCEPT NISMO
Item
Standard
Axle type
2WD
AWD
Camber
Degree minute (Decimal degree)
Minimum
–1
°
10
′
(–1.16
°
)
Nominal
–0
°
25
′
(–0.42
°
)
Maximum
0
°
20
′
(0.33
°
)
Left and right difference*
1
–0
°
45
′
(–0.75
°
) - 0
°
45
′
(0.75
°
)
Caster
Degree minute (Decimal degree)
Minimum
3
°
45
′
(3.75
°
)
3
°
50
′
(3.84
°
)
Nominal
4
°
30
′
(4.50
°
)
4
°
35
′
(4.58
°
)
Maximum
5
°
15
′
(5.25
°
)
5
°
20
′
(5.33
°
)
Left and right difference*
1
–0
°
45
′
(–0.75
°
) - 0
°
45
′
(0.75
°
)
Kingpin inclination
Degree minute (Decimal degree)
Minimum
10
°
40
′
(10.67
°
)
Nominal
11
°
25
′
(11.42
°
)
Maximum
12
°
10
′
(12.16
°
)
Toe-in
Total toe-in
Distance
Minimum
0 mm (0.00 in)
Nominal
In 2 mm (In 0.08 in)
Maximum
In 4 mm (In 0.16 in)
Total toe-angle
Degree minute (Decimal degree)
Minimum
Out 0
°
02
′
00
″
(Out 0.03
°
)
Nominal
In 0
°
10
′
00
″
(In 0.17
°
)
Maximum
In 0
°
22
′
00
″
(In 0.36
°
)
Item
Standard
Swing torque
0.5 – 4.9 N·m (0.06 – 0.49 kg-m, 5 – 43 in-lb)
Measurement on spring balance
15.4 – 150.8 N (1.6 – 15.3 kg, 3.5 – 33.8 lb)
Axial end play
0 mm (0 in)
Item
Standard
Axle type
2WD
AWD
Transmission
M/T
CVT
Front (Hf)
734 mm (28.90 in)
735 mm (28.94 in)
734 mm (28.90 in)
Revision: November 2015
2016 JUKE
FSU-20
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
NISMO
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
FOR CANADA MODELS
EXCEPT NISMO
Rear (Hr)
745 mm (29.33 in)
746 mm (29.37 in)
741 mm (29.17 in)
Item
Standard
Axle type
2WD
AWD
Transmission
M/T
CVT
SFA746B
Item
NISMO
NISMO RS
NISMO
NISMO RS
Axle type
2WD
AWD
Front (Hf)
724 mm (28.50 in)
725 mm (28.54 in)
724 mm (28.50 in)
Rear (Hr)
738 mm (29.06 in)
739 mm (29.09 in)
735 mm (28.94 in)
SFA746B
Item
Standard
Axle type
2WD
AWD
Transmission
M/T
CVT
Front (Hf)
735 mm (28.94 in)
735 mm (28.94 in)
735 mm (28.94 in)
Revision: November 2015
2016 JUKE
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-21
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
NISMO
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Rear (Hr)
745 mm (29.33 in)
746 mm (29.37 in)
741 mm (29.17 in)
Item
Standard
Axle type
2WD
AWD
Transmission
M/T
CVT
SFA746B
Item
NISMO
NISMO RS
NISMO
NISMO RS
Axle type
2WD
AWD
Front (Hf)
727 mm (28.62 in)
725 mm (28.54 in)
726 mm (28.58 in)
724 mm (28.50 in)
Rear (Hr)
740 mm (29.13 in)
740 mm (29.13 in)
735 mm (28.94 in)
735 mm (28.94 in)
SFA746B
Revision: November 2015
2016 JUKE
A
B
D
E
F
G
H
I
J
K
L
M
N
P
O
C
Q
QUICK REFERENCE INDEX
A GENERAL INFORMATION
B ENGINE
C ELECTRIC POWER TRAIN
HBC
Hybrid Control System
HBB
Hybrid Battery System
HBR
Hybrid Brake System
EVC
EV Control System
TMS
Traction Motor System
EVB
EV Battery System
VC
Vehicle Charging System
HCO
High Voltage Cooling System
D TRANSMISSION & DRIVELINE
E SUSPENSION
SCS
Suspension Control System
F BRAKES
G STEERING
H RESTRAINTS
SBC
Seat Belt Control System
I
VENTILATION, HEATER & AIR
CONDITIONER
Heater & Air Conditioning System
Heater & Air Conditioning Control System
J BODY INTERIOR
ADP
Automatic Drive Positioner
K BODY EXTERIOR, DOORS,
ROOF & VEHICLE SECURITY
HD
Hood
L DRIVER CONTROLS
VSP
Approaching Vehicle Sound for Pedestrians (VSP)
M ELECTRICAL & POWER CON-
TROL
Power Supply, Ground & Circuit Elements
N DRIVER INFORMATION &
MULTIMEDIA
Meter, Warning Lamp & Indicator
SN
Sonar System
Audio, Visual & Navigation System
O CRUISE CONTROL &
DRIVER ASSISTANCE
DAS
Driver Assistance System
P MAINTENANCE
Q INDEX
All Rights Reserved. No part
of this Service Manual may
be reproduced or stored in a
retrieval system, or transmit-
ted in any form, or by any
means, electronic, mechani-
cal, recording or otherwise,
without the prior written per-
mission of NISSAN MOTOR
CO., LTD.
Edition: September 2015
Revision: November 2015
Publication No. SM16E00F15U1
FOREWORD
This manual contains maintenance and repair procedure for the 2016
NISSAN JUKE.
In order to assure your safety and the efficient functioning of the vehicle,
this manual should be read thoroughly. It is especially important that the
PRECAUTIONS in the GI section be completely understood before starting
any repair task.
All information in this manual is based on the latest product information
at the time of publication. The right is reserved to make changes in specifi-
cations and methods at any time without notice.
IMPORTANT SAFETY NOTICE
The proper performance of service is essential for both the safety of
the technician and the efficient functioning of the vehicle.
The service methods in this Service Manual are described in such a
manner that the service may be performed safely and accurately.
Service varies with the procedures used, the skills of the technician
and the tools and parts available. Accordingly, anyone using service
procedures, tools or parts which are not specifically recommended
by NISSAN must first be completely satisfied that neither personal
safety nor the vehicle’s safety will be jeopardized by the service
method selected.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст