Nissan Juke (2016 year). Service Repair Manual — part 587
B0098 FRONT DOOR SATELLITE SENSOR RH
SRC-63
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199615
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK DTC
Perform each inspection according to the displayed DTC.
Which DTC is displayed?
[B0098–86] >> GO TO 4.
Other than the above >> GO TO 2.
2.
CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO-1 >> Damage: Replace malfunctioning harness and connector.
NO-2 >> Disconnection or looseness: Securely lock the connector.
3.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace malfunctioning harness and connector.
4.
REPLACE FRONT DOOR SATELLITE SENSOR RH
1. Replace front door satellite sensor RH. Refer to
SR-26, "Removal and Installation"
.
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: November 2015
2016 JUKE
SRC-64
< DTC/CIRCUIT DIAGNOSIS >
B00A0 OCCUPANT DETECTION SYSTEM CONTROL UNIT
B00A0 OCCUPANT DETECTION SYSTEM CONTROL UNIT
DTC Description
INFOID:0000000012199616
DTC DETECTION LOGIC
POSSIBLE CAUSE
OCCUPANT SENS
• [B00A0–00]
- Connection malfunction or short circuit to power supply of harness or connector
- Internal malfunction of occupant detection sensor
- Internal malfunction of air bag diagnosis sensor unit
• [B00A0–02, B00A0–09]
- Connection malfunction of harness and connector
- Internal malfunction of occupant detection sensor
- Internal malfunction of air bag diagnosis sensor unit
OCCUPANT SENS C/U
• [B00A0–04, B00A0–83, B00A0–86, B00A0–87, B00A0–88, B00A0–8F]
- Connection malfunction or open circuit of harness and connector
- Internal malfunction of occupant detection sensor control unit
- Internal malfunction of air bag diagnosis sensor unit
• [B00A0–93]
- Connection malfunction of harness and connector
- Internal malfunction of occupant detection sensor control unit
- Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B00A0–00
OCCUPANT SENS
[Occupant Classification
System (Subfault)]
[ABNORMAL VOLTAGE]
Power supply malfunction of occupant detection sensor
B00A0–02
[UNIT MALFUNC]
Malfunction of occupant detection sensor
B00A0–09
[UNIT MALFUNC]
Malfunction of occupant detection sensor
B00A0–04
OCCUPANT SENS C/U
[Occupant Classification
System (Subfault)]
[UNIT MALFUNC]
Malfunction of occupant detection sensor control unit
B00A0–83
[COMM ERR]
• Communication malfunction of occupant detection sensor con-
trol unit
• Communication blank of occupant detection sensor control
unit
B00A0–86
[COMM ERR]
• Communication malfunction of occupant detection sensor con-
trol unit
• Communication blank of occupant detection sensor control
unit
B00A0–87
[COMM ERR]
• Communication malfunction of occupant detection sensor con-
trol unit
• Communication blank of occupant detection sensor control
unit
B00A0–88
[COMM ERR]
• Communication malfunction of occupant detection sensor con-
trol unit
• Communication blank of occupant detection sensor control
unit
B00A0–8F
[UNDEFINED]
Undefined status of occupant detection sensor control unit
B00A0–93
[RESET]
Reset malfunction of occupant detection sensor control unit
Revision: November 2015
2016 JUKE
B00A0 OCCUPANT DETECTION SYSTEM CONTROL UNIT
SRC-65
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
.
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199617
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace malfunctioning harness and connector.
3.
REPLACE OCCUPANT DETECTION SYSTEM CONTROL UNIT
1. Replace occupant detection system control unit. Refer to
SR-32, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE OCCUPANT DETECTION SYSTEM SEAT SENSOR
1. Replace seat frame. Refer to
SE-21, "Removal and Installation"
.
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 5.
NO
>> INSPECTION END
5.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: November 2015
2016 JUKE
SRC-66
< DTC/CIRCUIT DIAGNOSIS >
B00D5 PASSENGER AIR BAG OFF INDICATOR
B00D5 PASSENGER AIR BAG OFF INDICATOR
DTC Description
INFOID:0000000012199618
DTC DETECTION LOGIC
POSSIBLE CAUSE
[B00D5–04]
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D5–11]
• Connection malfunction or short circuit to ground of harness and connector
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D5–12]
• Connection malfunction or short circuit to power supply of harness and connector
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D5–13]
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
[B00D5–15]
• Connection malfunction or short circuit to power supply of harness and connector
• Connection malfunction or open circuit of harness and connector
• Internal malfunction of front passenger air bag OFF indicator
• Internal malfunction of air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
DTC
CONSULT screen items
DTC detecting condition
B00D5–04
PASS A/B INDCTR CKT [UNIT MALFUNC]
Malfunction in passenger air bag OFF indicator circuit
B00D5–11
PASS A/B INDCTR CKT [GND-SHORT]
Passenger air bag OFF indicator circuit is shorted to ground
B00D5–12
PASS A/B INDCTR CKT [VB-SHORT]
Passenger air bag OFF indicator circuit is shorted to power supply cir-
cuit
B00D5–13
PASS A/B INDCTR CKT [OPEN]
Passenger air bag OFF indicator circuit is open
B00D5–15
PASS A/B INDCTR CKT [PWE-SHORT/
OPEN]
Passenger air bag OFF indicator circuit is open or shorted to power
supply circuit
Revision: November 2015
2016 JUKE
B00D5 PASSENGER AIR BAG OFF INDICATOR
SRC-67
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
Diagnosis Procedure
INFOID:0000000012199619
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait 3 minutes
or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the connection of harness connector.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK PASSENGER AIR BAG OFF INDICATOR
1. Replace cluster lid C (passenger air bag OFF indicator).
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 4.
NO
>> INSPECTION END
4.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: November 2015
2016 JUKE
SRC-68
< DTC/CIRCUIT DIAGNOSIS >
B1400, B1401, B1402, B1403, B1404, B1405 AIR BAG DIAGNOSIS SENSOR
UNIT
B1400, B1401, B1402, B1403, B1404, B1405 AIR BAG DIAGNOSIS SEN-
SOR UNIT
DTC Description
INFOID:0000000012199620
DTC DETECTION LOGIC
POSSIBLE CAUSE
Malfunction in air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199621
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B1400–00
CONTROL UNIT
(airbag control unit)
[UNIT MALFUNC]
Air bag diagnosis sensor unit is malfunctioning
B1401–00
CONTROL UNIT
(airbag control unit internal
trouble, sensor2)
[UNIT MALFUNC]
B1402–00
CONTROL UNIT
(airbag control unit internal
trouble, sensor3)
[UNIT MALFUNC]
B1403–00
CONTROL UNIT
(airbag control unit internal
trouble, sensor4)
[UNIT MALFUNC]
B1404–00
CONTROL UNIT
(airbag control unit internal
trouble, sensor5)
[UNIT MALFUNC]
B1405–00
CONTROL UNIT
(airbag control unit internal
trouble, sensor6)
[UNIT MALFUNC]
Revision: November 2015
2016 JUKE
B1400, B1401, B1402, B1403, B1404, B1405 AIR BAG DIAGNOSIS SENSOR
UNIT
SRC-69
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
YES
>> GO TO 2.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
2.
CHECK WIRING HARNESS
Check the wiring harness externals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace malfunctioning harness and connector.
3.
REPLACE AIR BAG DIAGNOSIS SENSOR UNIT
1. Replace air bag diagnosis sensor unit. Refer to
SR-29, "Removal and Installation"
2. Perform DTC confirmation procedure. Refer to
.
Is DTC detected?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: November 2015
2016 JUKE
SRC-70
< DTC/CIRCUIT DIAGNOSIS >
B1406, B1407, B1408, B1409, B1410 AIR BAG DIAGNOSIS SENSOR UNIT
B1406, B1407, B1408, B1409, B1410 AIR BAG DIAGNOSIS SENSOR UNIT
DTC Description
INFOID:0000000012199622
DTC DETECTION LOGIC
POSSIBLE CAUSE
Malfunction in air bag diagnosis sensor unit
FAIL-SAFE
—
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAG RESULT
With CONSULT
1. Turn ignition switch ON.
2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT.
Without CONSULT
1. Turn ignition switch ON.
2. Check the air bag warning lamp status. Refer to
SRC-10, "On Board Diagnosis Function"
NOTE:
SRS does not enter the diagnosis mode if no malfunction is detected in the user mode.
Is malfunctioning part detected?
YES
>> Refer to
NO-1 >> To check malfunction symptom before repair: Refer to
GI-45, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000012199623
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal, and wait at least 3
minutes or more. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.
CHECK HARNESS CONNECTOR
Check the harness connector for disconnection, looseness or damage.
Is the inspection result normal?
YES
>> GO TO 2.
NO–1 >> Damage: Replace malfunctioning harness and connector.
NO–2 >> Disconnection or looseness: Securely lock the connector.
DTC
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
B1406–00
CONTROL UNIT
(airbag control unit internal
trouble, Energy Reserver)
[UNIT MALFUNC]
Air bag diagnosis sensor unit is malfunctioning
B1407–00
CONTROL UNIT
(airbag control unit internal
trouble, driver IC1)
[UNIT MALFUNC]
B1408–00
CONTROL UNIT
(airbag control unit internal
trouble, driver IC2)
[UNIT MALFUNC]
B1409–00
CONTROL UNIT
(airbag control unit internal
trouble, driver IC3)
[UNIT MALFUNC]
B1410–00
CONTROL UNIT
(airbag control unit internal
trouble, Power IC)
[UNIT MALFUNC]
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст