Nissan Juke (2016 year). Service Repair Manual — part 115
DLK-102
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
AUTO DOOR LOCK OPERATION DOES NOT OPERATE
AUTO DOOR LOCK OPERATION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000012196682
1.
CHECK “AUTO LOCK SET” SETTING IN “WORK SUPPORT”
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “AUTO LOCK SET” in “WORK SUPPORT” mode.
3. Check “AUTO LOCK SET” in “WORK SUPPORT”.
DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “AUTO LOCK SET” setting in “WORK SUPPORT”.
2.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Revision: November 2015
2016 JUKE
VEHICLE SPEED SENSING AUTO LOCK OPERATION DOES NOT OPERATE
DLK-103
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
VEHICLE SPEED SENSING AUTO LOCK OPERATION DOES NOT OPER-
ATE
Diagnosis Procedure
INFOID:0000000012196683
1.
CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
2.
CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Revision: November 2015
2016 JUKE
DLK-104
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE
IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000012196684
1.
CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
2.
CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
3.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Revision: November 2015
2016 JUKE
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-
ATE
DLK-105
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE
Diagnosis Procedure
INFOID:0000000012196685
1.
CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
2.
CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT”.
3.
CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
DLK-26, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
4.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Revision: November 2015
2016 JUKE
DLK-106
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000012196686
1.
CHECK DTC WITH BCM AND COMBINATION METER
Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1 >> Refer to
NO-2 >> Refer to
. (Combination meter)
2.
CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.
3. Check the “HAZARD ANSWER BACK” in “WORK SUPPORT”.
DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “HAZARD ANSWER BACK” in “WORK SUPPORT”.
3.
CHECK “ANS BACK I-KEY LOCK” SETTING IN “WORK SUPPORT”
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “ANS BACK I-KEY LOCK” in “WORK SUPPORT” mode.
3. Check the “ANS BACK I-KEY LOCK” in “WORK SUPPORT”.
DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “ANS BACK I-KEY LOCK” in “WORK SUPPORT”.
4.
CHECK “ANS BACK I-KEY UNLOCK” SETTING IN “WORK SUPPORT”
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT” mode.
3. Check the “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT”.
DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Set “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT”.
5.
CHECK HAZARD FUNCTION
Check hazard function.
DLK-80, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
DLK-82, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace the malfunctioning parts.
7.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
Revision: November 2015
2016 JUKE
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
DLK-107
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Revision: November 2015
2016 JUKE
DLK-108
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
KEY REMINDER FUNCTION DOES NOT OPERATE
KEY REMINDER FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000012196687
1.
CHECK DTC WITH BCM
Check that DTC is not detected with BCM.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
2.
CHECK “ANTI KEY LOCK IN FUNCTI” SETTING IN “WORK SUPPORT”
1. Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2. Select “ANTI KEY LOCK IN FUNCTI” in “WORK SUPPORT” mode.
3. Check “ANTI KEY LOCK IN FUNCTI” in “WORK SUPPORT”.
DLK-28, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “ANTI KEY LOCK IN FUNCTI” in “WORK SUPPORT”.
3.
CHECK DOOR SWITCH
Check door switch.
DLK-77, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK INSIDE KEY ANTENNA
Check inside key antenna.
• Instrument center: Refer to
.
• Luggage room: Refer to
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK UNLOCK SENSOR
Check unlock sensor.
DLK-88, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Revision: November 2015
2016 JUKE
OFF POSITION WARNING DOES NOT OPERATE
DLK-109
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
OFF POSITION WARNING DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000012196688
1.
CHECK DTC WITH BCM AND COMBINATION METER
Check that DTC is not detected with BCM and combination meter.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1 >> Refer to
NO-2 >> Refer to
. (Combination meter)
2.
CHECK DOOR SWITCH
Check front door switch (driver side).
DLK-77, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK COMBINATION METER BUZZER
Check combination meter buzzer.
WCS-40, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
DLK-82, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1. Replace BCM. Refer to
BCS-94, "Removal and Installation"
.
2. Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-45, "Intermittent Incident"
.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст