Nissan Juke (2016 year). Service Repair Manual — part 105
DLK-22
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
*: M/T models do not apply.
WARNING METHOD
The following table shows the alarm or warning methods with chime.
*: M/T models do not apply.
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
Take away warning
Door status changes
from open to close
• Ignition switch: Except LOCK position
• Door switch: ON to OFF (Door is open to close)
• Registered Intelligent Key is not detected inside the vehicle
Door status is open
• Door switch: ON (Door is open)
• Registered Intelligent Key is not detected inside the vehicle during Key ID ver-
ification for 5 seconds
Push button-ignition
switch operation
• Ignition switch: Except LOCK position
• Press push-button ignition switch
• Registered Intelligent Key is not detected inside the vehicle
Door lock operation warning
When door lock operation is requested while door lock operating condition of
door request switch not satisfied
Engine start information
Ignition switch is ON po-
sition
• Ignition switch: ON position
• Shift position: P position*
• Engine is stopped
Ignition switch is except
ON position
• Ignition switch: Except ON position
• Shift position: P position*
• Intelligent Key can be detected inside the vehicle
Intelligent Key low battery warning
BCM detects that Intelligent Key is low battery, after ignition switch is turned ON
Key ID warning
• Push-button ignition switch is pressed
• Registered Intelligent Key is not detected inside the vehicle
Warning/Information functions
Operation procedure
Warning/Information functions
“KEY” warn-
ing lamp
Shift P
warning
lamp
Warning chime
Engine start
operation in-
dicator lamp
Combination
meter buzzer
Intelligent
Key warning
buzzer
Intelligent Key system malfunction
Indicate
—
—
—
—
OFF position warning
For internal
—
—
Activate
—
—
For external*
—
—
—
Activate
—
P position warning*
For internal
Blink (yellow)
Indicate
Activate
—
—
For external
—
—
Active
—
ACC warning*
—
—
Activate
—
—
Take away warning
Door is open to close
Blink (yellow)
—
Activate
Activate
—
Door is open
—
—
—
—
Push-ignition switch opera-
tion
—
Activate
—
—
Door lock operation warning
—
—
—
Activate
—
Key ID warning
Blink (yellow)
—
—
—
—
Engine start information
—
—
—
—
Indicate
Intelligent Key low battery warning
Blink (green)
—
—
—
—
Revision: November 2015
2016 JUKE
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-23
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Warning function
In
te
llige
nt
Key
Ig
n
iti
on swi
tch
Do
or swit
ch
Do
or requ
es
t s
w
itch
In
si
de
ke
y an
ten
n
a
Out
si
de ke
y a
n
ten
n
a
In
te
llige
nt
Key
wa
rnin
g
bu
zz
er
Com
b
in
at
io
n m
e
te
r wa
rni
n
g bu
zz
er
CAN co
mm
un
ic
ati
on
s
ys
tem
BC
M
S
hif
t P wa
rni
ng
la
mp
E
ng
ine
s
tart
op
era
tio
n
ind
ic
ato
r l
am
p
“K
EY” warning lamp
Intelligent Key system malfunction
×
×
×
OFF position warning
For internal
×
×
×
×
For external
×
×
×
P position warning
×
×
×
×
×
×
ACC warning
×
×
×
×
Take away warning
Door is open or close
×
×
×
×
×
×
×
×
Door is open
×
×
×
×
×
×
Push-button ignition switch opera-
tion
×
×
×
×
×
×
×
Door lock operation warning
×
×
×
×
×
×
×
Key ID warning
×
×
×
×
×
Engine start information
×
×
×
×
×
×
Steering lock information
×
×
×
Intelligent Key low battery warning
×
×
×
×
×
Revision: November 2015
2016 JUKE
DLK-24
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
BACK DOOR OPENER SYSTEM
BACK DOOR OPENER SYSTEM
System Diagram
INFOID:0000000012196593
System Description
INFOID:0000000012196594
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed.
NOTE:
• When battery terminal is disconnected and reconnected during all doors unlock state, back door may not
open.
• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30
seconds after battery terminal is disconnected and BCM recognizes that all doors are in lock state.
• When battery terminal is reconnected and back door does not open, have BCM recognize that all doors are
in unlock state.
JMKIA6011GB
Back door opener switch operation
Operation condition
Back door open
• When back door is unlocked using back door opener request switch (selective unlock
mode), or after BCM outputs all doors unlock signal
• Vehicle speed is less than 5 km/h (3 MPH)
Revision: November 2015
2016 JUKE
DIAGNOSIS SYSTEM (BCM)
DLK-25
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000012998445
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: For models with automatic A/C, this diagnosis mode is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Air conditioning system
AIR CONDITONER
×
×
*
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
Revision: November 2015
2016 JUKE
DLK-26
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
DOOR LOCK
DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)
INFOID:0000000012196596
BCM CONSULT FUNCTION
CONSULT performs the following functions via CAN communication with BCM.
WORK SUPPORT
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)
LOCK>ACC
While turning power position from “LOCK”* *to “ACC”
ACC>ON
While turning power position from “ACC” to “IGN”
RUN>ACC
While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)
CRANK>RUN
While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)
RUN>URGENT
While turning power position from “RUN“ to “ACC” (Emergency
stop operation)
ACC>OFF
While turning power position from “ACC” to “OFF”
OFF>LOCK
While turning power position from “OFF” to “LOCK”*
OFF>ACC
While turning power position from “OFF” to “ACC”
ON>CRANK
While turning power position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode
LOCK
Power position is “LOCK”*
OFF
Power position is “OFF” (Ignition switch OFF)
ACC
Power position is “ACC” (Ignition switch ACC)
ON
Power position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Revision: November 2015
2016 JUKE
DIAGNOSIS SYSTEM (BCM)
DLK-27
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*: P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
INTELLIGENT KEY
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function mode can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 24km/h (15MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other than
the P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function mode can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other than
the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON to
OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 5: This item is displayed, but cannot be monitored
• MODE 6: This item is displayed, but cannot be monitored
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function mode can be selected from the following in this mode
• Off: Non-operational
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Lock and unlock operation
Monitor Item
Contents
REQ SW-DR
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-BD/TR
Indicated [On/Off] condition of back door request switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
Indicated [On/Off] condition of back door switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
KEY CYL LK-SW
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
Indicated [On/Off] condition of unlock signal from door key cylinder
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LOCK” on CONSULT screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT screen is
touched
• The door lock actuator (passenger side) is unlocked when “AS UNLK” on CONSULT screen is
touched
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT screen is touched
Revision: November 2015
2016 JUKE
DLK-28
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)
INFOID:0000000012196597
WORK SUPPORT
Monitor item
Description
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
HORN WITH KEYLESS LOCK
Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not
operate (OFF) with this mode
• On: Operate
• Off: Non-operation
PANIC ALARM SET
Panic alarm button pressing time on Intelligent Key remote control button can be selected from
the following with this mode
• MODE 1: 0.5 sec
• MODE 2: Non-operation
• MODE 3: 1.5 sec
TRUNK OPEN DELAY
NOTE:
This item is displayed, but cannot be monitored
LO- BATT OF KEY FOB WARN
Intelligent Key low battery warning mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
ANTI KEY LOCK IN FUNCTI
Key reminder function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
HAZARD ANSWER BACK
Hazard reminder function mode by door request switch and Intelligent Key button can be se-
lected from the following with this mode
• Lock Only: Door lock operation only
• Unlock Only: Door unlock operation only
• Lock/Unlock: Lock and unlock operation
• Off: Non-operation
ANS BACK I-KEY LOCK
Buzzer reminder function (lock operation) mode by door request switch can be selected from
the following with this mode
• Horn Chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• Off: Non-operation
ANS BACK I-KEY UNLOCK
Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
• On: Operate
• Off: Non-operation
SHORT CRANKING OUTPUT
Starter motor can operate during the times below
• 70 msec
• 100 msec
• 200 msec
Revision: November 2015
2016 JUKE
DIAGNOSIS SYSTEM (BCM)
DLK-29
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SELF-DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CONFIRM KEY FOB ID
It can be checked whether Intelligent Key ID code is registered or not in this mode
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
SFT PN/N SW
Indicates [On/Off] condition of P or N position
UNLK SEN -DR
Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
DETE SW -IPDM
Indicates [On/Off] condition of P position
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
SFT P -MET
Indicates [On/Off] condition of P position
SFT N -MET
Indicates [On/Off] condition of N position
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
S/L LOCK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L UNLK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L RELAY-REQ
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver side door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status
ID OK FLAG
Indicates [Set/Reset] condition of key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст