Nissan Juke (2016 year). Service Repair Manual — part 485
LU-12
< PERIODIC MAINTENANCE >
[MR FOR NISMO RS MODELS]
OIL FILTER
OIL FILTER
Removal and Installation
INFOID:0000000012197475
REMOVAL
1. Remove engine under cover.
2. Using oil filter wrench [SST: KV10115801 (J-38956)] (A), remove
oil filter.
CAUTION:
• Oil filter is provided with relief valve. Use genuine NISSAN
oil filter or equivalent.
• Be careful not to get burned when engine and engine oil
may be hot.
• When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3. Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn (A). Or tighten to specification.
Inspection
INFOID:0000000012197476
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to
.
2. Start the engine, and check that there is no leakage of engine oil.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level, and adjust the level. Refer to
.
: Vehicle front
JPBIA4450ZZ
SMA010
Oil filter:
: 17.7 N·m (1.8 kg-m, 13 ft-lb)
JPBIA0077ZZ
Revision: November 2015
2016 JUKE
OIL COOLER
LU-13
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
REMOVAL AND INSTALLATION
OIL COOLER
Exploded View
INFOID:0000000012197477
M/T models
JPBIA4444GB
1.
Clamp
2.
Water hose
3.
Oil cooler
4.
Water hose
: N·m (kg-m, in-lb)
Revision: November 2015
2016 JUKE
LU-14
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
OIL COOLER
CVT models
Removal and Installation
INFOID:0000000012197478
REMOVAL
1. Drain engine coolant. Refer to
CAUTION:
Perform when engine is cold.
2. Remove front bumper. Refer to
3. Remove charge air cooler. Refer to
4. Remove water hose.
5. Remove oil cooler.
INSTALLATION
Installation is in reverse order of removal.
Inspection
INFOID:0000000012197479
INSPECTION AFTER REMOVAL
Oil Cooler
Check oil cooler for cracks. Check oil cooler for clogging by blowing through engine coolant inlet. If necessary,
replace oil cooler assembly.
JPBIA4445GB
1.
Clamp
2.
Water hose
3.
Oil cooler
4.
Water hose
5.
Water hose
6.
Heater thermostat
A.
To CVT oil warmer
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
Revision: November 2015
2016 JUKE
OIL COOLER
LU-15
< REMOVAL AND INSTALLATION >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
INSPECTION AFTER INSTALLATION
1. Check the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer to
2. Start the engine, and check that there is no leakage of engine oil or engine coolant.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level and the engine coolant level again. Refer to
Revision: November 2015
2016 JUKE
LU-16
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR FOR NISMO RS MODELS]
OIL PUMP
UNIT DISASSEMBLY AND ASSEMBLY
OIL PUMP
Exploded View
INFOID:0000000012197480
1.
O-ring
2.
Oil pan (upper)
3.
Oil level gauge guide
4.
O-ring
5.
Oil level gauge
6.
Oil pump drive chain
7.
Crankshaft sprocket
8.
Oil pump sprocket
9.
Oil pump chain tensioner
10. Oil pump
11. Drain plug
12. Drain plug washer
13. Oil pan (lower)
14. Oil filter
15. Connector bolt
16. Clamp
17. Oil cooler hose
18. Oil cooler
19. Crankshaft position sensor
20. Gasket
21. Oil pan bolt
22. Rear oil seal
A.
Comply with the assembly proce-
dure when tightening. Refer to
B.
To thermostat housing
C.
To thermostat housing (M/T models)
To CVT oil warmer (CVT models)
D.
Oil pan side
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JPBIA4875GB
Revision: November 2015
2016 JUKE
OIL PUMP
LU-17
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
Removal and Installation
INFOID:0000000012197481
REMOVAL
1. Remove engine assembly. Refer to
(2WD) ,
(AWD).
2. Remove oil pan (lower). Refer to
EM-47, "Removal and Installation"
3. Remove front cover, and other related parts. Refer to
4. Remove oil pump sprocket with the following procedure:
• Add matching mark if necessary for easier installation.
a. Push oil pump drive chain tensioner (1) in the direction show in
the figure.
b. Insert a stopper pin (A) into the body hole (B).
c. Remove oil pump chain tensioner.
• When the holes on lever and tensioner body cannot be
aligned, align these holes by slightly moving the oil pump
chain tensioner slack guide.
d. Hold the WAF part of oil pump shaft [WAF: 10 mm (0.39 in)] (A),
and then loosen the oil pump sprocket bolt and remove it.
CAUTION:
• Secure the oil pump shaft with the WAF part.
• Never loosen the oil pump sprocket bolt by tightening the
oil pump drive chain.
e. Remove oil pump sprocket.
5. Remove oil pump.
: Should be lubricated with oil.
: Sealing point
: Indicates that the parts is connected at points with same symbols in actual vehicle.
JPBIA4397ZZ
1
: Oil pan (upper)
: Engine front
JPBIA4398ZZ
Revision: November 2015
2016 JUKE
LU-18
< UNIT DISASSEMBLY AND ASSEMBLY >
[MR FOR NISMO RS MODELS]
OIL PUMP
• Loosen bolts in reverse order as shown in the figure.
INSTALLATION
Note the following, and install in the reverse order of removal.
Oil Pump
• Tighten bolts in numerical order as shown in the figure.
Inspection
INFOID:0000000012197482
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to
.
2. Start the engine, and check that there is no leakage of engine oil.
3. Stop the engine and wait for 10 minutes.
4. Check the engine oil level, and adjust the level. Refer to
.
1
: Oil pump
2
: Oil pan (upper)
: Engine front
JPBIA4451ZZ
1
: Oil pump
2
: Oil pan (upper)
: Engine front
JPBIA4451ZZ
Revision: November 2015
2016 JUKE
SERVICE DATA AND SPECIFICATIONS (SDS)
LU-19
< SERVICE DATA AND SPECIFICATIONS (SDS)
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Periodical Maintenance Specification
INFOID:0000000012197483
ENGINE OIL CAPACITY (APPROXIMATE)
Unit: (US qt, lmp qt)
Engine Oil Pressure
INFOID:0000000012197484
Unit: kPa (kg/cm
2
, psi)
*: Engine oil temperature at 80
°
C (176
°
F)
Drain and refill
With oil filter change
4.5 (4-6/8, 4)
Without oil filter change
4.3 (4-4/8, 3-6/8)
Dry engine (Overhaul)
5.4 (5-6/8, 4-6/8)
Engine speed
Approximate discharge pressure*
Idle speed
90 (0.92, 13.1)
2,000 rpm
260 (2.65, 37.7)
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст