Nissan Juke (2016 year). Service Repair Manual — part 399
FL-24
< REMOVAL AND INSTALLATION >
[MR16DDT ]
FUEL TANK
12. Support right of fuel tank (1) with transmission jack (A), and then
remove fuel tank band mounting bolts (LH).
13. Supporting with hands, descend transmission jack carefully, and remove fuel tank with fuel tank band
(LH).
CAUTION:
Fuel tank may be in an unstable condition because of the shape of fuel tank bottom. Never rely on
jack too much. Be sure to hold tank securely.
INSTALLATION
Note the following, and install in the reverse order of removal.
Fuel Filler Hose
• Insert fuel filler hose to the length below.
• Be sure hose clamp is not placed on swelled area of fuel filler tube.
• Tighten the clamp band with the top mark (A) until the mark is on
the bolt head flange.
EVAP Hose
1. Check connections for damage or foreign material.
2. Align the matching side connection part with the center of shaft,
and insert connector straight until it clicks.
3. After connecting, pull out quick connector and centralized under-
floor piping by hand. Make sure connections are secure.
AWD : Inspection
INFOID:0000000012197596
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leakage.
1. Turn ignition switch “ON” (with engine stopped), and check connections for leakage by applying fuel pres-
sure to fuel piping.
JPBIA4476ZZ
: 35 mm (1.38 in)
JPBIA0146ZZ
A
: Pull
JPBIA0140ZZ
Revision: November 2015
2016 JUKE
FUEL TANK
FL-25
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
2. Start engine and rev it up and check there are no fuel leakage at the fuel system tube and hose connec-
tions.
Revision: November 2015
2016 JUKE
FL-26
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EVAP CANISTER
EVAP CANISTER
2WD
2WD : Hydraulic Layout
INFOID:0000000012197597
EVAPORATIVE EMISSION LINE DRAWING
JPBIA4890ZZ
Revision: November 2015
2016 JUKE
EVAP CANISTER
FL-27
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
NOTE:
Do not use soapy water or any type of solvent while installing vacuum hose or purge hoses.
2WD : Exploded View
INFOID:0000000012197598
2WD : Removal and Installation
INFOID:0000000012197599
REMOVAL
1. Disconnect harness connectors (EVAP control pressure sensor and EVAP canister vent control valve) and
EVAP canister hoses.
2. Remove EVAP canister fixing bolt.
3. Remove EVAP canister.
NOTE:
EVAP canister vent control valve and EVAP control pressure sensor can be removed without removing
the EVAP canister.
INSTALLATION
CAUTION:
Do not reuse O-rings.
Install in the reverse order of removal.
1.
EVAP canister purge volume control
solenoid valve
2.
EVAP service port
3.
EVAP canister
4.
EVAP control pressure sensor
5.
EVAP canister vent control valve
6.
EAVP line
7.
Fuel line
1.
EVAP canister
2.
EVAP control pressure sensor
3.
O-ring
4.
O-ring
5.
EVAP canister vent control valve
6.
EVAP canister hose
7.
Canister filter
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JPBIA4877GB
Revision: November 2015
2016 JUKE
FL-28
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EVAP CANISTER
NOTE:
Tighten EVAP canister fixing bolt to the specified torque.
2WD : Disassembly and Assembly
INFOID:0000000012197600
DISASSEMBLY
1. Disengage the pawl and turn EVAP canister vent control valve
counterclockwise.
• Lock (A)
• Unlock (B)
2. Remove the EVAP canister vent control valve.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
Always replace O-ring with a new one.
2WD : Inspection
INFOID:0000000012197601
Check EVAP canister as per the following:
1. Block port (B).
2. Blow air into port (A) and check that it flows freely out of port (C).
3. Release blocked port (B).
4. Apply vacuum pressure to port (B) and check that vacuum pres-
sure exists at the ports (A) and (C).
5. Block port (A) and (B).
6. Apply pressure to port (C) and check that there is no leakage.
AWD
AWD : Hydraulic Layout
INFOID:0000000012197602
EVAPORATIVE EMISSION LINE DRAWING
PBIB3091E
PBIB1212E
Revision: November 2015
2016 JUKE
EVAP CANISTER
FL-29
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
NOTE:
Do not use soapy water or any type of solvent while installing vacuum hose or purge hoses.
1.
EVAP canister purge volume control
solenoid valve
2.
EVAP service port
3.
EVAP canister
4.
EVAP control pressure sensor
5.
EVAP canister vent control valve
6.
EAVP line
7.
Fuel line
JPBIA4891ZZ
Revision: November 2015
2016 JUKE
FL-30
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EVAP CANISTER
AWD : Exploded View
INFOID:0000000012197603
AWD : Removal and Installation
INFOID:0000000012197604
REMOVAL
1. Remove rear stabilizer (1). Refer to
2. Disconnect harness connectors (EVAP control pressure sensor
and EVAP canister vent control valve) and EVAP canister hoses.
3. Remove EVAP canister fixing bolt.
4. Remove EVAP canister.
NOTE:
EVAP canister vent control valve and EVAP control pressure
sensor can be removed without removing the EVAP canister.
INSTALLATION
CAUTION:
Do not reuse O-rings.
Install in the reverse order of removal.
NOTE:
Tighten EVAP canister fixing bolt to the specified torque.
1.
EVAP canister
2.
EVAP control pressure sensor
3.
O-ring
4.
O-ring
5.
EVAP canister vent control valve
6.
Canister filter
7.
EVAP canister hose
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JPBIA4878GB
2.
EVAP canister
JPBIA4329ZZ
Revision: November 2015
2016 JUKE
EVAP CANISTER
FL-31
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
FL
N
P
O
AWD : Disassembly and Assembly
INFOID:0000000012197605
DISASSEMBLY
1. Disengage the pawl and turn EVAP canister vent control valve
counterclockwise.
• Lock (A)
• Unlock (B)
2. Remove the EVAP canister vent control valve.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
Always replace O-ring with a new one.
AWD : Inspection
INFOID:0000000012197606
Check EVAP canister as per the following:
1. Block port (B).
2. Blow air into port (A) and check that it flows freely out of port (C).
3. Release blocked port (B).
4. Apply vacuum pressure to port (B) and check that vacuum pres-
sure exists at the ports (A) and (C).
5. Block port (A) and (B).
6. Apply pressure to port (C) and check that there is no leakage.
PBIB3091E
PBIB1212E
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст