Nissan Juke (2016 year). Service Repair Manual — part 419
CONDENSER
HA-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
5. Remove mounting bolt (A), and then disconnect high-pressure
pipe (1).
CAUTION:
Cap or wrap the joint of the A/C piping and condenser with
suitable material such as vinyl tape to avoid the entry of air.
6. Remove mounting bolt (A), and then disconnect high-pressure
flexible hose.
CAUTION:
Cap or wrap the joint of the A/C piping and condenser with
suitable material such as vinyl tape to avoid the entry of air.
7. Remove mounting bolts, and then remove condenser from the vehicle.
CAUTION:
Be careful not to damage core surface of condenser.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Perform lubricant adjusting procedure before installing new condenser. Refer to
Adjusting Procedure for Compressor Replacement"
• Check for leakages when recharging refrigerant. Refer to
LIQUID TANK
LIQUID TANK : Removal and Installation
INFOID:0000000012197132
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
21, "Perform Lubricant Return Operation"
REMOVAL
1. Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to
2. Remove bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
3. Remove air guide LH. Refer to
DLK-130, "MR16DDT : Exploded View"
4. Clean liquid tank and its surrounding area, and then remove dust and rust from liquid tank.
CAUTION:
Be sure to clean carefully.
5. Disconnect refrigerant pressure sensor harness connector.
6. Remove mounting bolts, and then remove liquid tank from condenser.
CAUTION:
• Be careful not to damage core surface of condenser and liquid tank.
• Cap or wrap the joint of the A/C piping and liquid tank with suitable material such as vinyl tape to
avoid the entry of air.
INSTALLATION
: Vehicle front
JMIIA0975ZZ
: Vehicle front
JMIIA0949ZZ
Revision: November 2015
2016 JUKE
HA-38
< REMOVAL AND INSTALLATION >
CONDENSER
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-rings of the A/C piping with new ones. Then apply compressor oil to them when installing.
• Perform lubricant adjusting procedure before installing new liquid tank. Refer to
Adjusting Procedure for Compressor Replacement"
.
• Check for leakages when recharging refrigerant. Refer to
REFRIGERANT PRESSURE SENSOR
REFRIGERANT PRESSURE SENSOR : Removal and Installation
INFOID:0000000012197133
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
21, "Perform Lubricant Return Operation"
REMOVAL
1. Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to
2. Remove front bumper fascia. Refer to
EXT-17, "Removal and Installation"
.
3. Clean refrigerant pressure sensor and its surrounding area, and then remove dust and rust from refriger-
ant pressure sensor.
CAUTION:
Be sure to clean carefully.
4. Remove liquid tank. Refer to
HA-37, "LIQUID TANK : Removal and Installation"
CAUTION:
• Be careful not to damage liquid tank.
• Cap or wrap the joint of the condenser and liquid tank with suitable material such as vinyl tape to
avoid the entry of air.
5. Fix the liquid tank (1) using a vice (A).
6. Remove refrigerant pressure sensor (2) using a wrench (B).
CAUTION:
Be careful not to damage liquid tank.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace O-ring with new one. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant. Refer to
JSIIA0075ZZ
Revision: November 2015
2016 JUKE
A/C UNIT ASSEMBLY
HA-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
A/C UNIT ASSEMBLY
Exploded View (Automatic Air Conditioning)
INFOID:0000000012197134
REMOVAL
DISASSEMBLY
1.
A/C unit assembly
2.
Drain hose
3.
Steering member
4.
Instrument stay
: Clip
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSIIA1819GB
Revision: November 2015
2016 JUKE
HA-40
< REMOVAL AND INSTALLATION >
A/C UNIT ASSEMBLY
1.
Ventilator seal
2.
Defroster seal
3.
Upper attachment case
4.
Sub defroster door
5.
Center ventilator and defroster door 6.
Side ventilator seal LH
7.
Lower attachment case
8.
Side ventilator seal RH
9.
Sub harness
10. Power transistor
11. Upper intake case
12. Intake door
13. Lower intake case
14. Blower case LH
15. Blower case RH
16. Blower motor
17. Intake seal
18. A/C unit case RH
19. In-cabin microfilter
20. Filter cover
21. Case packing
22. Intake sensor
23. Evaporator
24. Plate
25. Expansion valve grommet
26. O-ring
27. Expansion valve
28. Evaporator cover
29. Heater hose
30. Clamp
31. Heater pipe grommet
32. Heater pipe support
33. Heater core
34. A/C unit case LH
35. Aspirator duct
36. Aspirator
37. Foot door
38. Foot door rod
39. Side ventilator door
40. Air mix door guide
41. Upper air mix door
42. Lower air mix door
A.
To water outlet
JMIIA0982GB
Revision: November 2015
2016 JUKE
A/C UNIT ASSEMBLY
HA-41
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
Exploded View (Manual Air Conditioning)
INFOID:0000000012197135
REMOVAL
DISASSEMBLY
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
1.
A/C unit assembly
2.
Drain hose
3.
Steering member
4.
Instrument stay
: Clip
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
JSIIA1819GB
Revision: November 2015
2016 JUKE
HA-42
< REMOVAL AND INSTALLATION >
A/C UNIT ASSEMBLY
1.
Ventilator seal
2.
Defroster seal
3.
Upper attachment case
4.
Center ventilator door
5.
Defroster door
6.
Side ventilator seal LH
7.
Lower attachment case
8.
Side ventilator seal RH
9.
Sub harness
10. Blower fan resistor
11. Upper Intake case
12. Intake door
13. Sub intake door
14. Lower intake case
15. Blower case LH
16. Blower case RH
17. Blower motor
18. Intake seal
19. A/C unit case RH
20. In-cabin microfilter
21. Filter cover
22. Case packing
23. Thermo control amp.
24. Evaporator
25. Plate
26. Expansion valve grommet
27. O-ring
28. Expansion valve
29. Evaporator cover
30. Heater hose
31. Clamp
32. Heater pipe grommet
33. Heater pipe support
34. Heater core
35. A/C unit case LH
36. Foot door
37. Foot door rod
38. Side ventilator door
39. Air mix door guide
40. Upper air mix door
41. Lower air mix door
A.
To water outlet
JMIIA1212GB
Revision: November 2015
2016 JUKE
A/C UNIT ASSEMBLY
HA-43
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
A/C UNIT ASSEMBLY
A/C UNIT ASSEMBLY : Removal and Installation
INFOID:0000000012197136
CAUTION:
Perform lubricant return operation before each refrigeration system disassembly. However, if a large
amount of refrigerant or lubricant is detected, never perform lubricant return operation. Refer to
21, "Perform Lubricant Return Operation"
REMOVAL
1. Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant. Refer to
2. Drain engine coolant from cooling system. Refer to
(MR for NISMO RS models) or
(MR except for NISMO RS models).
3. Remove cowl top and cowl top extension. Refer to
EXT-30, "Removal and Installation"
.
4. Remove mounting nut, and then move lower dash insulator
aside.
5. Remove mounting bolt (A), and then disconnect low-pressure
flexible hose (1) and high-pressure pipe (2) from expansion
HA-46, "EXPANSION VALVE : Removal and
.
CAUTION:
Cap or wrap the joint of the A/C piping and expansion valve
with suitable material such as vinyl tape to avoid the entry
of air.
6. Remove fixing clamps (1), and then disconnect heater hoses (2)
7. Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
8. Remove side ventilator duct LH and RH. Refer to
VTL-11, "SIDE VENTILATOR DUCT : Removal and
.
: Always replace after every disassembly.
: N·m (kg-m, in-lb)
: Nut
: Vehicle front
JMIIA0973ZZ
: Vehicle front
JMIIA0974ZZ
: Vehicle front
JMIIA0986ZZ
Revision: November 2015
2016 JUKE
HA-44
< REMOVAL AND INSTALLATION >
A/C UNIT ASSEMBLY
9. Remove mounting bolts (A) of ground wire LH side and mounting bolt (B) of ground wire RH side.
10. Remove rear heater duct 1 LH and RH. Refer to
VTL-11, "REAR HEATER DUCT 1 : Removal and Instal-
(for Canada models only).
11. Disconnect drain hose from A/C unit assembly.
12. Remove mounting nuts (A), and then remove instrument stay.
13. Remove fixing screws (A), and then remove junction box (J/B).
JMIIA0989ZZ
: Vehicle front
JMIIA0987ZZ
: Vehicle front
JMIIA0988ZZ
JMIIA0886ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст