Nissan Juke (2016 year). Service Repair Manual — part 198
P0500 VSS
EC-399
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> GO TO 2.
NO
>> GO TO 5.
2.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.
CHECK VEHICLE SPEED SIGNAL
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a
road test is expected to be easier, it is unnecessary to lift the vehicle.
With CONSULT
1. Start engine.
2. Read “VHCL SPEED SE” in “DATA MONITOR” mode of “ENGINE” using CONSULT. The vehicle speed
on CONSULT should exceed 10 km/h (6 mph) when rotating wheels with suitable gear position.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Proceed to
EC-400, "M/T MODELS : Diagnosis Procedure"
.
4.
PERFORM DTC CONFIRMATION PROCEDURE
1. Select “DATA MONITOR” mode of “ENGINE” using CONSULT.
2. Warm engine up to normal operating temperature.
3. Maintain the following conditions for at least 50 consecutive seconds.
CAUTION:
Always drive vehicle at a safe speed.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
EC-400, "M/T MODELS : Diagnosis Procedure"
.
NO
>> INSPECTION END
5.
PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to
EC-399, "M/T MODELS : Component Function Check"
.
Use component function check to check the overall function of the vehicle speed signal circuit. During this
check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
EC-400, "M/T MODELS : Diagnosis Procedure"
.
M/T MODELS : Component Function Check
INFOID:0000000012197934
1.
PERFORM COMPONENT FUNCTION CHECK
With GST
1. Lift up drive wheels.
2. Start engine.
3. Read vehicle speed signal in Service $01 with GST.
ENG SPEED
1,800 - 6,000 rpm
COOLAN TEMP/S
More than 65
°
C (149
°
F)
B/FUEL SCHDL
6.25 - 31.8 msec
Selector lever
Except Neutral position
PW/ST SIGNAL
OFF
Revision: November 2015
2016 JUKE
EC-400
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
P0500 VSS
The vehicle speed signal on GST should be able to exceed 10 km/h (6 MPH) when rotating wheels with
suitable gear position.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Proceed to
EC-400, "M/T MODELS : Diagnosis Procedure"
.
M/T MODELS : Diagnosis Procedure
INFOID:0000000012197935
1.
CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check DTC with ABS actuator and electric unit (control unit). Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform trouble shooting relevant to DTC indicated.
2.
CHECK DTC WITH COMBINATION METER
Check DTC with combination meter. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform trouble shooting relevant to DTC indicated.
Revision: November 2015
2016 JUKE
P0501, P2159 VEHICLE SPEED SENSOR
EC-401
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0501, P2159 VEHICLE SPEED SENSOR
Description
INFOID:0000000012197936
ECM receives a rear wheel sensor signal from ABS actuator and electric unit (control unit) via CAN communi-
cation to switch combustion for the direct injection gasoline system. For the direct injection gasoline system,
refer to
EC-51, "DIRECT INJECTION GASOLINE SYSTEM : System Description"
DTC Logic
INFOID:0000000012197937
DTC DETECTION LOGIC
NOTE:
If DTC P0501 or P2159 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TEST CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 9 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for at least 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012197938
1.
CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
With CONSULT
Check DTC with ABS actuator and electric unit (control unit). Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform Diagnosis Procedure corresponding to DTC indicated.
DTC No.
Trouble diagnosis
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0501
VEHICLE SPEED SEN A
(Vehicle speed sensor A range/
performance)
ECM detects a rear LH wheel sensor mal-
function signal transmitted from the ABS ac-
tuator and electric unit (control unit) via CAN
communication at least for 5 seconds in a
row.
• Harness or connectors
(The CAN communication line is open
or shorted)
• Rear LH wheel sensor
• ABS actuator and electric unit (control
unit)
P2159
Vehicle speed sensor B
(Vehicle speed sensor B range/
performance)
ECM detects a rear RH wheel sensor mal-
function signal transmitted from the ABS ac-
tuator and electric unit (control unit) via CAN
communication at least for 5 seconds in a
row.
• Harness or connectors
(The CAN communication line is open
or shorted)
• Rear RH wheel sensor
• ABS actuator and electric unit (control
unit)
Revision: November 2015
2016 JUKE
EC-402
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
P0506 ISC SYSTEM
P0506 ISC SYSTEM
Description
INFOID:0000000012197939
The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let
into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is
varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects
the actual engine speed and sends a signal to the ECM.
The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value
memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.
The optimum value stored in the ECM is determined by taking into consideration various engine conditions,
such as during warming up, deceleration, and engine load (air conditioner, power steering and cooling fan
operation, etc.).
DTC Logic
INFOID:0000000012197940
DTC DETECTION LOGIC
NOTE:
If DTC P0506 is displayed with other DTC, first perform the trouble diagnosis for the other DTC.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
If the target idle speed is out of the specified value, perform
, before conducting
DTC Confirmation Procedure.
TESTING CONDITION:
•
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
•
Always perform the test at a temperature above
−
10
°
C (14
°
F).
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Start engine and run it for at least 1 minute at idle speed.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012197941
1.
CHECK INTAKE AIR LEAK
1. Start engine and let it idle.
2. Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?
YES
>> Discover air leak location and repair.
DTC No.
Trouble diagnosis
(Trouble diagnosis con-
tent)
DTC detecting condition
Possible cause
P0506
ISC SYSTEM
(Idle speed control system
RPM lower than expected)
The idle speed is less than the target idle
speed by 100 rpm or more.
• Electric throttle control actuator
• Intake air leak
Revision: November 2015
2016 JUKE
P0506 ISC SYSTEM
EC-403
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
NO
>> Replace ECM. Refer to
EC-590, "Removal and Installation"
Revision: November 2015
2016 JUKE
EC-404
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
P0507 ISC SYSTEM
P0507 ISC SYSTEM
Description
INFOID:0000000012197942
The ECM controls the engine idle speed to a specified level through the fine adjustment of the air, which is let
into the intake manifold, by operating the electric throttle control actuator. The operating of the throttle valve is
varied to allow for optimum control of the engine idling speed. The crankshaft position sensor (POS) detects
the actual engine speed and sends a signal to the ECM.
The ECM controls the electric throttle control actuator so that the engine speed coincides with the target value
memorized in the ECM. The target engine speed is the lowest speed at which the engine can operate steadily.
The optimum value stored in the ECM is determined by taking into consideration various engine conditions,
such as during warming up, deceleration, and engine load (air conditioner, power steering and cooling fan
operation, etc.).
DTC Logic
INFOID:0000000012197943
DTC DETECTION LOGIC
NOTE:
If DTC P0507 is displayed with other DTC, first perform the trouble diagnosis for the other DTC.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
If the target idle speed is out of the specified value, perform
, before conducting
DTC Confirmation Procedure.
TESTING CONDITION:
•
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
•
Always perform the test at a temperature above
−
10
°
C (14
°
F).
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and warm it up to normal operating temperature.
2. Turn ignition switch OFF and wait at least 10 seconds.
3. Start engine and run it for at least 1 minute at idle speed.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000012197944
1.
CHECK PCV HOSE CONNECTION
Confirm that PCV hose is connected correctly.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
DTC No.
Trouble diagnosis name
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0507
ISC SYSTEM
(Idle speed control system
RPM higher than expected)
The idle speed is more than the target idle
speed by 200 rpm or more.
• Electric throttle control actuator
• Intake air leak
• PCV system
Revision: November 2015
2016 JUKE
P0507 ISC SYSTEM
EC-405
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
2.
CHECK INTAKE AIR LEAK
1. Start engine and let it idle.
2. Listen for an intake air leak after the mass air flow sensor.
Is intake air leak detected?
YES
>> Discover air leak location and repair.
NO
>> Replace ECM. Refer to
EC-590, "Removal and Installation"
Revision: November 2015
2016 JUKE
EC-406
< DTC/CIRCUIT DIAGNOSIS >
[MR FOR NISMO RS MODELS]
P050A, P050E COLD START CONTROL
P050A, P050E COLD START CONTROL
Description
INFOID:0000000012197945
ECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition.
This control promotes the activation of three way catalyst by heating the catalyst and reduces emissions.
DTC Logic
INFOID:0000000012197946
DTC DETECTION LOGIC
NOTE:
If DTC P050A, P050B or P050E is displayed with other DTC, first perform the trouble diagnosis for
other DTC.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE-I
With CONSULT
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Select “DATA MONITOR” mode of “ENGINE” using CONSULT.
4. Check the indication of “COOLAN TEMP/S”.
With GST
Follow the procedure “With CONSULT” above.
Is the value of “COOLAN TEMP/S” between 4
°
C (39
°
F) and 36
°
C (97
°
F)?
YES
>> GO TO 3.
NO-1 [If it is below 4
°
C (39
°
F)]>>Warm up the engine until the value of “COOLAN TEMP/S” reaches 4
°
C
(39
°
F) or more. Retry from step 1.
NO-2 [If it is above 36
°
C (97
°
F)]>>Cool engine down to less than 36
°
C (97
°
F). Retry from step 1.
3.
PERFORM DTC CONFIRMATION PROCEDURE-II
With CONSULT
1. Set the select lever in N range.
2. Start the engine and warm up in idle with the value of “COOLAN TEMP/S” between 5
°
C (41
°
F) and 40
°
C
(104
°
F) for more than 15 seconds.
3. Check 1st trip DTC.
With GST
Follow the procedure “With CONSULT” above.
Is 1st trip DTC detected?
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P050A
Cold start idle air control system
performance
ECM does not control engine idle speed properly
when engine is started with pre-warming up con-
dition.
• Lack of intake air volume
• Fuel injection system
• ECM
P050E
Cold start engine exhaust temper-
ature too low
The temperature of the catalyst inlet does not
rise to the proper temperature when the engine
is started with pre-warming up condition.
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст