Nissan Juke (2016 year). Service Repair Manual — part 448
INTERIOR ROOM LAMP CONTROL CIRCUIT
INL-41
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
Is the inspection result normal?
YES
>> Replace map lamp.Refer to
INL-46, "Removal and Installation"
.
NO
>> Repair or replace harnesses.
3.
CHECK INTERIOR ROOM LAMP CONTROL SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and map lamp connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harnesses.
BCM
Ground
Continuity
Connector
Terminal
M69
63
Not existed
Revision: November 2015
2016 JUKE
INL-42
< DTC/CIRCUIT DIAGNOSIS >
LUGGAGE ROOM LAMP CIRCUIT
LUGGAGE ROOM LAMP CIRCUIT
Description
INFOID:0000000012197016
Controls the luggage room lamp (ground side) to turn the luggage room lamp ON and OFF.
Diagnosis Procedure
INFOID:0000000012197017
NOTE:
Before performing the diagnosis, check that the following are normal.
• Interior room lamp power supply
• Luggage room lamp bulb
1.
CHECK LUGGAGE ROOM LAMP OUTPUT
1. Turn ignition switch OFF.
2. Remove the luggage room lamp bulb.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1 >> Continuity exists and remains unchanged: GO TO 3.
NO-2 >> Continuity does not exist and remains unchanged: Replace BCM. Refer to
2.
CHECK LUGGAGE ROOM LAMP OPEN CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and luggage room lamp harness connector.
Is the inspection result normal?
YES
>> Replace luggage room lamp.
NO
>> Repair or replace harnesses.
3.
CHECK LUGGAGE ROOM LAMP SHORT CIRCUIT
1. Disconnect BCM connector.
2. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harnesses.
BCM
Ground
Condition
Continuity
Connector
Terminal
B10
49
Back door
Open
Existed
Closed
Not existed
BCM
Luggage room lamp
Continuity
Connector
Terminal
Connector
Terminal
B10
49
B11
2
Existed
BCM
Ground
Continuity
Connector
Terminal
B10
49
Not existed
Revision: November 2015
2016 JUKE
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
INL-43
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
Description
INFOID:0000000012197018
Provides the power supply and the ground to control the push-button ignition switch illumination.
Component Function Check
INFOID:0000000012197019
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION OPERATION
CONSULT ACTIVE TEST
1. Turn the ignition switch ON.
2. Select “ENGINE SW ILLUMI” of BCM (INTELLIGENT KEY) active test item.
3. With operating the test items, check that the push-button ignition switch illumination turns ON/OFF.
Does the push-button ignition switch illumination turn ON/OFF?
YES
>> Push-button ignition switch illumination circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000012197020
1.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION POWER SUPPLY OUTPUT
CONSULT ACTIVE TEST
1. Turn ignition switch ON.
2. Select ENGINE SW ILLUMI of BCM (INTELLIGENT KEY) active test item.
3. With operating the test item, check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
2.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION GROUND
CONSULT ACTIVE TEST
With operating the test item, check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO-1 >> Continuity exists and remains unchanged: GO TO 4.
NO-2 >> Continuity does not exist and remains unchanged: Replace BCM. Refer to
3.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and push-button ignition switch connector.
On
: Push-button ignition switch illumination ON
Off
: Push-button ignition switch illumination OFF
(+)
(–)
Condition
Voltage
BCM
Connector
Terminal
M70
90
Ground
ENGINE SW ILLUMI
On
12 V
Off
0 V
BCM
Ground
Test item
Continuity
Connector
Terminal
M70
92
ENGINE SW ILLUMI
On
Existed
Off
Not existed
Revision: November 2015
2016 JUKE
INL-44
< DTC/CIRCUIT DIAGNOSIS >
PUSH-BUTTON IGNITION SWITCH ILLUMINATION CIRCUIT
3. Check continuity between BCM harness connector and push-button ignition switch harness connector.
Is the inspection result normal?
YES
>> Replace push-button ignition switch.
NO
>> Repair or replace harnesses.
4.
CHECK PUSH-BUTTON IGNITION SWITCH ILLUMINATION SHORT CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector and push-button ignition switch connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harnesses.
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M70
90
M101
5
Existed
BCM
Push-button ignition switch
Continuity
Connector
Terminal
Connector
Terminal
M70
92
M101
6
Existed
Push-button ignition switch
Ground
Continuity
Connector
Terminal
M70
92
Not existed
Revision: November 2015
2016 JUKE
INTERIOR LIGHTING SYSTEM SYMPTOMS
INL-45
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SYMPTOM DIAGNOSIS
INTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000012197021
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Symptom
Possible cause
Inspection item
All the following lamps do not turn ON.
• Map lamp
• Luggage room lamp
• Harness between BCM and each
interior room lamp
• BCM
Interior room lamp power supply cir-
cuit
Refer to
.
• Interior room lamp does not turn ON even
though the door is open.
(It turns ON when turning the interior room
lamp ON.)
• Interior room lamp does not turn OFF even
though the door is closed.
• Harness between BCM and each
door switch
• Harness between BCM and each
interior room lamp
• BCM
Door switch circuit
Refer to
.
Interior room lamp control circuit
Refer to
.
Interior room lamp timer does not activate.
(It turns ON/ OFF when the door opens/closes.)
—
Check the interior room lamp setting.
Refer to
.
• Luggage room lamp does not turn ON even
though the back door is open.
• Luggage room lamp does not turn OFF even
though the back door is closed.
• Harness between BCM and back
door switch
• Harness between BCM and lug-
gage room lamp
• BCM
Back door switch circuit
Refer to
.
Luggage room lamp circuit
Refer to
.
Push-button ignition switch illumination does not
illuminate.
• Harness between BCM and push-
button ignition switch
• BCM
Push-button ignition switch illumina-
tion circuit
Refer to
.
Interior room lamp battery saver does not acti-
vate.
BCM
Replace BCM.
Refer to
Revision: November 2015
2016 JUKE
INL-46
< REMOVAL AND INSTALLATION >
MAP LAMP
REMOVAL AND INSTALLATION
MAP LAMP
Exploded View
INFOID:0000000012197022
Removal and Installation
INFOID:0000000012197023
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage.
1. Disengage lens fixing pawls using a remover tool (A), and then
remove lens (1).
CAUTION:
• Use a remover tool wrapped in tape.
• Insert a remover tool into the gap between bulb housing
and lens.
2. Disengage bulb housing (1) fixing pawl using a remover tool (A)
according to numerical order 1
→
2 indicated by the arrows as
shown in the figure.
CAUTION:
Use a remover tool wrapped in tape.
3. Disconnect map lamp harness connector, and then remove bulb housing.
1.
Bulb housing
2.
Bulb
3.
Lens
: Pawl
JMLIA1062ZZ
: Pawl
JMLIA1063ZZ
: Pawl
JMLIA1064ZZ
Revision: November 2015
2016 JUKE
MAP LAMP
INL-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000012197024
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
MAP LAMP BULB
1. Disengage lens fixing pawls using a remover tool (A), and then
remove lens (1).
CAUTION:
• Use a remover tool wrapped in tape.
• Insert a remover tool into the gap between bulb housing
and lens.
2. Remove bulb.
: Pawl
JMLIA1063ZZ
Revision: November 2015
2016 JUKE
INL-48
< REMOVAL AND INSTALLATION >
GLOVE BOX LAMP
GLOVE BOX LAMP
Exploded View
INFOID:0000000012197025
Removal and Installation
INFOID:0000000012197026
Replacement
INFOID:0000000012197027
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
GLOVE BOX LAMP BULB
1. Remove glove box assembly. Refer to
IP-13, "Removal and Installation"
2. Rotate the bulb & socket assembly counterclockwise and unlock
it, and then remove bulb & socket assembly.
1.
Bulb housing
2.
Bulb & socket assembly
3.
Glove box assembly
: Pawl
: Vehicle front
JMLIA3198ZZ
JMLIA1528ZZ
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст