Nissan Juke (2016 year). Service Repair Manual — part 15
AV-108
< WIRING DIAGRAM >
[AUDIO WITH NAVIGATION]
NAVIGATION SYSTEM
JRNWF0752GB
Revision: November 2015
2016 JUKE
AV
DIAGNOSIS AND REPAIR WORKFLOW
AV-109
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
NAVIGATION SYSTEM
NAVIGATION SYSTEM : Work Flow
INFOID:0000000012202508
OVERALL SEQUENCE
• Reference 1··· Refer to
.
• Reference 2··· Refer to
• Reference 3··· Refer to
DETAILED FLOW
1.
INTERVIEW AND SYMPTOM CONFIRMATION
Check the malfunction symptoms by performing the following items.
• Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred).
• Check the symptom.
Is the occurred symptom malfunction?
YES
>> GO TO 2.
NO
>> INSPECTION END
JSNIA4482GB
Revision: November 2015
2016 JUKE
AV-110
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
DIAGNOSIS AND REPAIR WORKFLOW
2.
DIAGNOSIS WITH CONSULT
1. Connect CONSULT and perform a self-diagnosis for “MULTI AV”. Refer to
NOTE:
Skip to step 4 of the diagnosis procedure if “MULTI AV” is not displayed.
2. When DTC is detected, follow the instructions below:
-
Record DTC and Freeze Frame Data.
Is DTC displayed?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
TROUBLE DIAGNOSIS FOR DTC
1. Check the DTC indicated in the self-diagnosis results.
2. Perform the relevant diagnosis referring to the DTC Index. Refer to
.
>> GO TO 5.
4.
TROUBLE DIAGNOSIS FOR SYMPTOMS
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to
.
>> GO TO 5.
5.
ERROR PART REPAIR
1. Repair or replace the identified malfunctioning parts.
2. Perform a self-diagnosis for “MULTI AV” with CONSULT.
NOTE:
Erase the stored self-diagnosis results after repairing or replacing the relevant components if any DTC
has been indicated in the self-diagnosis results.
3. Check that the symptom does not occur.
Does the symptom occur?
YES
>> GO TO 1.
NO
>> INSPECTION END
AROUND VIEW MONITOR SYSTEM
Revision: November 2015
2016 JUKE
AV
DIAGNOSIS AND REPAIR WORKFLOW
AV-111
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
AROUND VIEW MONITOR SYSTEM : Work Flow
INFOID:0000000012202509
OVERALL SEQUENCE
• Reference 1··· Refer to
.
• Reference 2··· Refer to
• Reference 3··· Refer to
DETAILED FLOW
1.
INTERVIEW AND SYMPTOM CONFIRMATION
Check the malfunction symptoms by performing the following items.
• Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred).
• Check the symptom.
Is the occurred symptom malfunction?
YES
>> GO TO 2.
NO
>> INSPECTION END
2.
DIAGNOSIS WITH CONSULT
1. Connect CONSULT and perform a self-diagnosis for “AVM”. Refer to
.
NOTE:
Skip to step 4 of the diagnosis procedure if “AVM” is not displayed.
2. When DTC is detected, follow the instructions below:
JSNIA4482GB
Revision: November 2015
2016 JUKE
AV-112
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
DIAGNOSIS AND REPAIR WORKFLOW
-
Record DTC and Freeze Frame Data.
Is DTC displayed?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
TROUBLE DIAGNOSIS FOR DTC
1. Check the DTC indicated in the self-diagnosis results.
2. Perform the relevant diagnosis referring to the DTC Index. Refer to
.
>> GO TO 5.
4.
TROUBLE DIAGNOSIS FOR SYMPTOMS
Perform the relevant diagnosis referring to the diagnosis chart by symptom. Refer to
.
>> GO TO 5.
5.
ERROR PART REPAIR
1. Repair or replace the identified malfunctioning parts.
2. Perform a self-diagnosis for “AVM” with CONSULT.
NOTE:
Erase the stored self-diagnosis results after repairing or replacing the relevant components if any DTC
has been indicated in the self-diagnosis results.
3. Check that the symptom does not occur.
Does the symptom occur?
YES
>> GO TO 1.
NO
>> INSPECTION END
Revision: November 2015
2016 JUKE
AV
INSPECTION AND ADJUSTMENT
AV-113
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING NAVI CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING NAVI CONTROL UNIT : Description
INFOID:0000000012202510
Perform the following operations when replacing NAVI control unit.
AV-113, "CONFIGURATION (NAVI CONTROL UNIT) : Description"
.
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CON-
TROL UNIT
ADDITIONAL SERVICE WHEN REPLACING AROUND VIEW MONITOR CONTROL
UNIT : Description
INFOID:0000000012202511
Perform the calibrating camera image when replacing around view monitor control unit. Refer to
"CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Work Procedure"
.
CONFIGURATION (NAVI CONTROL UNIT)
CONFIGURATION (NAVI CONTROL UNIT) : Description
INFOID:0000000012202512
• Since vehicle specifications are not included in the NAVI control unit after replacement, it is required to write
vehicle specifications with CONSULT. Refer to
AV-113, "CONFIGURATION (NAVI CONTROL UNIT) : Spe-
• The NAVI control unit configuration includes functions as follows.
CONFIGURATION (NAVI CONTROL UNIT) : Special Repair Requirement
INFOID:0000000012202513
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “Before Replace ECU”, and save the current vehicle specification in CONSULT.
Is the vehicle specification saved normally?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
REPLACE NAVI CONTROL UNIT
Replace NAVI control unit. Refer to
AV-182, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Select “Configuration” or “After Replace ECU”, and write the vehicle specification saved in CONSULT to NAVI
control unit.
>> GO TO 6.
4.
REPLACE NAVI CONTROL UNIT
Replace NAVI control unit. Refer to
AV-182, "Removal and Installation"
Function
Description
Read/Write Configuration
Before Replace ECU
Allows the reading of vehicle specification written in NAVI control
unit to store the specification in CONSULT.
After Replace ECU
Allows the writing of the vehicle information stored in CONSULT
into the NAVI control unit.
Manual Configuration
Allows the writing of the vehicle specification into the NAVI control
unit by hand.
Revision: November 2015
2016 JUKE
AV-114
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
INSPECTION AND ADJUSTMENT
>> GO TO 5.
5.
WRITE VEHICLE SPECIFICATION
CONSULT Configuration
Select “Manual Configuration”, and write the setting value as shown in the following table to NAVI control unit
according to the vehicle specification.
CAUTION:
Grasp vehicle specifications precisely. The control of ECU may not function normally if the specifica-
tions are misread.
NOTE:
• The items shown in this list depend on vehicle specifications.
• The config list may not be displayed depending on vehicle specifications. This is not a malfunction.
• If selection items are not displayed on the CONSULT screen, touch “NEXT”.
>> GO TO 6.
6.
PERFORM SELF-DIAGNOSIS
CONSULT Self Diagnostic Result
Perform self-diagnosis of CONSULT, and check whether or not DTC U12AA is detected.
Is DTC U12AA detected?
YES
>> GO TO 5.
NO
>> GO TO 7.
7.
OPERATION CHECK
Check that the operation of the NAVI control unit is normal.
>> WORK END
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT)
MANUAL SETTING ITEM
Detail
Items
Setting value
TRANSMISSION
MT
M/T models
CVT
CVT models
AT
A/T models
OTHER
Except for above
SOUND SYSTEM
BASE
—
BOSE
With BOSE system
BOSE SURROUND
With BOSE surround system
ROCKFORD FOSGATE
Without BOSE system without woof-
er
ROCKFORD SUB WOOFER
Without BOSE system with woofer
CAMERA SYSTEM
NONE
—
AVM
—
NONE/AVM
Without camera system or with
around view monitor system
REAR
With rear view monitor system
REAR+SIDE
With rear view monitor system and
front-side view monitor function
AVM+PA
With around view monitor system
and parking assist function
Revision: November 2015
2016 JUKE
AV
INSPECTION AND ADJUSTMENT
AV-115
< BASIC INSPECTION >
[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
CONFIGURATION (AROUND VIEW MONITOR CONTROL UNIT) : Work Procedure
INFOID:0000000012202514
1.
SAVING VEHICLE SPECIFICATION
CONSULT Configuration
Perform “Before Replace ECU”, and save the current vehicle specification in CONSULT.
Is the vehicle specification saved normally?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
>> GO TO 3.
3.
WRITING VEHICLE SPECIFICATION
CONSULT Configuration
Select “Configuration” or “After Replace ECU”, and write the vehicle specification saved in CONSULT to
around view monitor control unit.
>> GO TO 6.
4.
REPLACE AROUND VIEW MONITOR CONTROL UNIT
Replace around view monitor control unit. Refer to
AV-190, "Removal and Installation"
>> GO TO 5.
5.
WRITE VEHICLE SPECIFICATION
CONSULT Configuration
Select “WRITE CONFIGURATION - Manual selection” and write in the following list at a around view monitor
control unit depending on a vehicle specification.
>> GO TO 6.
6.
PERFORM SELF-DIAGNOSIS
CONSULT Self Diagnostic Result
Perform self-diagnosis of CONSULT, and check whether or not DTC U1305 is detected.
Is DTC U1305 detected?
YES
>> GO TO 5.
NO
>> GO TO 7.
7.
OPERATION CHECK
Check that the operation of the around view monitor control unit and camera images (fixed guide lines and
predictive course lines) are normal.
>> WORK END
PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT
Setting item
Detail
Items
Setting value
TRANSMISSION
A/T
CVT models
M/T
M/T models
Revision: November 2015
2016 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст