Nissan Pathfinder (2006 year). Manual — part 315
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-75
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
5.
CHECK HAZARD SWITCH
1.
Disconnect hazard switch connector.
2.
Check continuity of hazard switch.
OK or NG
OK
>> Replace BCM if hazard warning lamps do not work after
setting the connector again. Refer to
.
NG
>> Replace hazard switch. Refer to
LT-78, "Removal and Installation"
Turn Signal Indicator Lamp Does Not Operate
EKS00FW4
1.
CHECK CAN COMMUNICATION SYSTEM
Check CAN communication. Refer to
OK or NG
OK
>> Replace combination meter. Refer to
NG
>> Repair as necessary.
Hazard switch
Condition
Continuity
Terminal
2
1
Hazard switch is ON
Yes
Hazard switch is OFF
No
PKIA4601E
LT-76
TURN SIGNAL AND HAZARD WARNING LAMPS
2006 Pathfinder
Bulb Replacement
EKS00FW5
FRONT TURN SIGNAL LAMP
LT-27, "FRONT TURN SIGNAL/PARKING LAMP"
.
REAR TURN SIGNAL LAMP
Removal and Installation
EKS00FW7
FRONT TURN SIGNAL LAMP
LT-27, "Removal and Installation"
.
REAR TURN SIGNAL LAMP
LIGHTING AND TURN SIGNAL SWITCH
LT-77
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
LIGHTING AND TURN SIGNAL SWITCH
PFP:25540
Removal and Installation
EKS00FW9
REMOVAL
1.
Remove instrument lower cover LH. Refer to
IP-14, "LOWER INSTRUMENT PANEL LH"
2.
Remove steering column cover.
3.
Disconnect the lighting and turn signal switch connector.
4.
While pressing tabs, pull lighting and turn signal switch toward
driver door and release from the steering column.
INSTALLATION
Installation is in the reverse order of removal.
LKIA0013E
LT-78
HAZARD SWITCH
2006 Pathfinder
HAZARD SWITCH
PFP:25290
Removal and Installation
EKS00FWA
REMOVAL
1.
Remove cluster lid C. Refer to
IP-11, "CLUSTER LID C -WITHOUT NAVIGATION SYSTEM"
2.
Disconnect the hazard switch connector.
3.
Remove the screws and remove the hazard switch.
INSTALLATION
Installation is in the reverse order of removal.
LKIA0575E
COMBINATION SWITCH
LT-79
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
COMBINATION SWITCH
PFP:25567
Wiring Diagram — COMBSW —
EKS00FWB
WKWA4229E
LT-80
COMBINATION SWITCH
2006 Pathfinder
Combination Switch Reading Function
EKS00FWC
For details, refer to
BCS-3, "COMBINATION SWITCH READING FUNCTION"
CONSULT-II Function (BCM)
EKS00FWD
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1.
With the ignition switch OFF, connect CONSULT-II and CON-
SULT-II CONVERTER to the data link connector, then turn igni-
tion switch ON.
2.
Touch "START (NISSAN BASED VHCL)".
3.
Touch "BCM" on "SELECT SYSTEM" screen.
If "BCM" is not indicated, go to
BCM diagnostic
test item
Diagnostic mode
Description
Inspection by part
WORK SUPPORT
Supports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR
Displays BCM input/output data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS
Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER
BCM part number can be read.
CONFIGURATION
Performs BCM configuration read/write functions.
BBIA0538E
BCIA0029E
BCIA0030E
COMBINATION SWITCH
LT-81
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
4.
Touch "COMB SW" on "SELECT TEST ITEM" screen.
DATA MONITOR
Operation Procedure
1.
Touch "COMB SW" on "SELECT TEST ITEM" screen.
2.
Touch "DATA MONITOR" on "SELECT DIAG MODE" screen.
3.
Touch either "ALL SIGNALS" or "SELECTION FROM MENU" on "SELECT MONITOR ITEM" screen.
4.
Touch "START".
5.
When "SELECTION FROM MENU" is selected, touch items to be monitored. When "ALL SIGNALS" is
selected, all the signals will be monitored.
6.
Touch "RECORD" while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch "STOP".
Display Item List
LKIA0183E
ALL SIGNALS
Monitors all the signals.
SELECTION FROM MENU
Selects and monitors individual signal.
Monitor item name
"OPERATION OR UNIT"
Contents
TURN SIGNAL R
"ON/OFF"
Displays "Turn Right (ON)/Other (OFF)" status, determined from lighting switch signal.
TURN SIGNAL L
"ON/OFF"
Displays "Turn Left (ON)/Other (OFF)" status, determined from lighting switch signal.
HI BEAM SW
"ON/OFF"
Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from lighting
switch signal.
HEAD LAMP SW 1
"ON/OFF"
Displays "Headlamp switch 1 (ON)/Other (OFF)" status, determined from lighting switch signal.
HEAD LAMP SW 2
"ON/OFF"
Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from lighting
switch signal.
LIGHT SW 1ST
"ON/OFF"
Displays status (lighting switch 1st position: ON/Others: OFF) of lighting switch judged from lighting
switch signal.
PASSING SW
"ON/OFF"
Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged from lighting
switch signal.
AUTO LIGHT SW
"ON/OFF"
Displays "Auto light switch (ON)/Other (OFF)" status, determined from lighting switch signal.
FR FOG SW
"ON/OFF"
Displays "Front fog lamp switch (ON)/Other (OFF)" status, determined from lighting switch signal.
FR WIPER HI
"ON/OFF"
Displays "Front Wiper HI (ON)/Other (OFF)" status, determined from wiper switch signal.
FR WIPER LOW
"ON/OFF"
Displays "Front Wiper LOW (ON)/Other (OFF)" status, determined from wiper switch signal.
FR WIPER INT
"ON/OFF"
Displays "Front Wiper INT (ON)/Other (OFF)" status, determined from wiper switch signal.
FR WASHER SW
"ON/OFF"
Displays "Front Washer Switch (ON)/Other (OFF)" status, determined from wiper switch signal.
INT VOLUME
[1 - 7]
Displays intermittent operation knob setting (1 - 7), determined from wiper switch signal.
RR WIPER ON
"ON/OFF"
Displays "Rear Wiper (ON)/(OFF)" status, determined from wiper switch signal.
RR WIPER INT
"ON/OFF"
Displays "Rear Wiper INT (ON)/(OFF)" status, determined from wiper switch signal.
RR WASHER SW
"ON/OFF" Displays "Rear Washer (ON)/(OFF)" status, determined from wiper switch signal.
LT-82
COMBINATION SWITCH
2006 Pathfinder
Combination Switch Inspection
EKS00FWE
1.
SYSTEM CHECK
Referring to table below, check to which system the malfunctioning switch belongs.
>> GO TO 2.
2.
SYSTEM CHECK
With CONSULT-II
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1.
Connect CONSULT-II, and select "COMB SW" on "SELECT
TEST ITEM" screen.
2.
Select "DATA MONITOR".
3.
Select "START", and confirm that other switches in malfunction-
ing system operate normally.
Example: When auto light switch is malfunctioning, confirm that
"FRONT WIPER LOW" and "FRONT WIPER INT" in System 3,
to which the auto light switch belongs, turn ON-OFF normally.
Without CONSULT-II
Operate combination switch, and confirm that other switches in malfunctioning system operate normally.
Example: When auto light switch is malfunctioning, confirm that "FRONT WIPER LOW" and "FRONT WIPER
INT" in System 3, to which the auto light switch belongs, operate normally.
Check results
Other switches in malfunctioning system operate normally.>>Replace lighting switch or wiper switch.
Other switches in malfunctioning system do not operate normally.>>GO TO 3.
System 1
System 2
System 3
System 4
System 5
—
FR WASHER
FR WIPER LO
TURN LH
TURN RH
FR WIPER HI
—
FR WIPER INT
PASSING
HEAD LAMP1
INT VOLUME 1
RR WASHER
—
HEAD LAMP2
HI BEAM
RR WIPER INT
INT VOLUME 3
AUTO LIGHT
—
TAIL LAMP
INT VOLUME 2
RR WIPER ON
—
FR FOG
—
SKIA7075E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст