Nissan Pathfinder (2006 year). Manual — part 308
HEADLAMP (FOR USA)
LT-19
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
5.
CHECK HEADLAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector E123
terminal 56 and front headlamp RH harness connector E107 ter-
minal 1.
4.
Check continuity between IPDM E/R harness connector E123
terminal 55 and front headlamp LH harness connector E11 ter-
minal 1.
OK or NG
OK
>> Replace IPDM E/R. Refer to
PG-32, "Removal and Installation of IPDM E/R"
NG
>> Repair harness or connector.
6.
CHECK HEADLAMP GROUND
1.
Turn ignition switch OFF.
2.
Check continuity between front headlamp RH harness connec-
tor E107 terminal 2 and ground.
3.
Check continuity between front headlamp LH harness connector
E11 terminal 2 and ground.
OK or NG
OK
>> Check front headlamp connector for damage or poor
connection. Repair as necessary.
NG
>> Repair harness or connector.
Headlamp HI Does Not Illuminate (One Side)
EKS00FUB
1.
BULB INSPECTION
Inspect inoperative headlamp bulb.
OK or NG
OK
>> GO TO 2.
NG
>> Replace headlamp bulb. Refer to
56 - 1
: Continuity should exist.
55 - 1
: Continuity should exist.
WKIA3498E
2 - Ground
: Continuity should exist.
2 - Ground
: Continuity should exist.
WKIA3499E
LT-20
HEADLAMP (FOR USA)
2006 Pathfinder
2.
CHECK POWER TO HEADLAMP
1.
Disconnect inoperative headlamp connector.
2.
Turn the high beam headlamps ON.
3.
Check voltage between inoperative headlamp terminal and
ground.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
3.
CHECK HEADLAMP GROUND
1.
Turn the high beam headlamps OFF.
2.
Check continuity between inoperative headlamp connector and
ground.
OK or NG
OK
>> Check front headlamp connector for damage or poor
connection. Repair as necessary.
NG
>> Repair open circuit in harness between inoperative
headlamp and ground.
4.
INSPECTION BETWEEN IPDM E/R AND HEADLAMPS
1.
Disconnect IPDM E/R connector and inoperative headlamp connector.
2.
Check continuity between harness connector terminals of IPDM
E/R and harness connector terminals of inoperative headlamp.
OK or NG
OK
>> Replace IPDM E/R. Refer to
NG
>> Check for short and open circuits in harness between
IPDM E/R and front headlamps. Repair as necessary.
High Beam Indicator Lamp Does Not Illuminate
EKS00FUC
1.
BULB INSPECTION
Inspect CAN communication system. Refer to
OK or NG
OK
>> Replace combination meter. Refer to
NG
>> Repair as necessary.
Front headlamp
(–)
Voltage
(Approx.)
(+)
Connector
Terminal
RH
E107
1
Ground Battery
voltage
LH
E11
WKIA3497E
Front headlamp
Continuity
Connector
Terminal
RH
E107
2
Ground Yes
LH
E11
WKIA3499E
IPDM E/R
Front headlamp
Continuity
Connector
Terminal
Connector
Terminal
E123
56
RH
E107
1
Yes
55
LH
E11
WKIA3498E
HEADLAMP (FOR USA)
LT-21
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
Headlamp LO Does Not Illuminate (Both Sides)
EKS00FUD
1.
CHECK COMBINATION SWITCH INPUT SIGNAL
Select "BCM" on CONSULT-II. With "HEAD LAMP" data monitor,
make sure "HEAD LAMP SW 1" and "HEAD LAMP SW 2" turns ON-
OFF linked with operation of lighting switch.
OK or NG
OK
>> GO TO 2.
NG
>> Check lighting switch. Refer to
2.
HEADLAMP ACTIVE TEST
1.
Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST"
on "SELECT DIAG MODE" screen.
2.
Select "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
3.
Touch "LO" on "ACTIVE TEST" screen.
4.
Make sure headlamp low beam operates.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
3.
CHECK IPDM E/R
1.
Select "IPDM E/R" on CONSULT-II, and select "DATA MONI-
TOR" on "SELECT DIAG MODE" screen.
2.
Make sure "HL LO REQ" turns ON when lighting switch is in
2ND position.
OK or NG
OK
>> Replace IPDM E/R. Refer to
NG
>> Replace BCM. Refer to
BCS-27, "Removal and Installa-
When lighting switch is in
2ND position
: HEAD LAMP SW 1 ON
: HEAD LAMP SW 2 ON
WKIA4262E
Headlamp low beam should operate.
WKIA1438E
When lighting switch is in
2ND position
: HL LO REQ ON
SKIA5780E
LT-22
HEADLAMP (FOR USA)
2006 Pathfinder
4.
CHECK HEADLAMP INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front headlamp RH and LH connectors.
3.
Turn ignition switch ON.
4.
Select "IPDM E/R" on CONSULT-II, and select "ACTIVE TEST" on "SELECT DIAG MODE" screen.
5.
Select "EXTERNAL LAMPS" on "SELECT TEST ITEM" screen.
6.
Touch "LO" on "ACTIVE TEST" screen.
7.
When headlamp low beam is operating, check voltage between
front headlamp RH and LH harness connector and ground.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 5.
5.
CHECK HEADLAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector E123
terminal 54 and front headlamp RH harness connector E107 ter-
minal 3.
4.
Check continuity between IPDM E/R harness connector E123
terminal 52 and front headlamp LH harness connector E11 ter-
minal 3.
OK or NG
OK
>> Replace IPDM E/R. Refer to
PG-32, "Removal and Installation of IPDM E/R"
NG
>> Repair harness or connector.
6.
CHECK HEADLAMP GROUND
1.
Turn ignition switch OFF.
2.
Check continuity between front headlamp RH harness connec-
tor E107 terminal 2 and ground.
3.
Check continuity between front headlamp LH harness connector
E11 terminal 2 and ground.
OK or NG
OK
>> Check front headlamp connector for damage or poor
connection. Repair as necessary.
NG
>> Repair harness or connector.
Front headlamp
(–)
Voltage
(+)
Connector
Terminal
RH
E107
3
Ground Battery
voltage
LH
E11
WKIA3500E
54 - 3
: Continuity should exist.
52 - 3
: Continuity should exist.
WKIA3501E
2 - Ground
: Continuity should exist.
2 - Ground
: Continuity should exist.
WKIA3499E
HEADLAMP (FOR USA)
LT-23
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
Headlamp LO Does Not Illuminate (One Side)
EKS00FUE
1.
BULB INSPECTION
Inspect inoperative headlamp bulb.
OK or NG
OK
>> GO TO 2.
NG
>> Replace headlamp bulb. Refer to
2.
CHECK POWER TO HEADLAMP
1.
Disconnect inoperative headlamp connector.
2.
Turn the low beam headlamps ON.
3.
Check voltage between inoperative headlamp connector termi-
nal and ground.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 4.
3.
CHECK HEADLAMP GROUND
1.
Turn the low beam headlamps OFF.
2.
Check continuity between inoperative headlamp connector ter-
minal and ground.
OK or NG
OK
>> Check front headlamp and IPDM E/R connector. Repair
as necessary.
NG
>> Repair open circuit in harness between inoperative
headlamp and ground.
4.
INSPECTION BETWEEN IPDM E/R AND HEADLAMPS
1.
Disconnect IPDM E/R connector.
2.
Check continuity between harness connector terminals of IPDM
E/R harness connector terminals of inoperative headlamp.
OK or NG
OK
>> Replace IPDM E/R. Refer to
NG
>> Check for short and open circuits in harness between
IPDM E/R and headlamps. Repair as necessary.
Front headlamp
(–)
Voltage
(Approx.)
(+)
Connector
Terminal
RH
E107
3
Ground
Battery voltage
LH
E11
WKIA4990E
Front headlamp
Continuity
Connector
Terminal
RH
E107
2
Ground Yes
LH
E11
WKIA3499E
IPDM E/R
Front headlamp
Continuity
Connector
Terminal
Connector
Terminal
E123
54
RH
E107
3
Yes
52
LH
E11
WKIA3501E
LT-24
HEADLAMP (FOR USA)
2006 Pathfinder
Headlamps Do Not Turn OFF
EKS00FUF
1.
CHECK COMBINATION SWITCH INPUT SIGNAL
Select "BCM" on CONSULT-II. With "HEAD LAMP" data monitor,
make sure "HEAD LAMP SW 1" and "HEAD LAMP SW 2" turns ON-
OFF linked with operation of lighting switch.
OK or NG
OK
>> Replace IPDM E/R. Refer to
NG
>> GO TO 2.
2.
CHECK LIGHTING SWITCH
Check lighting switch. Refer to
LT-82, "Combination Switch Inspection"
.
OK or NG
OK
>> GO TO 3.
NG
>> Replace lighting switch. Refer to
LT-84, "Removal and Installation"
3.
CHECKING CAN COMMUNICATIONS BETWEEN BCM AND IPDM E/R
Select "BCM" on CONSULT-II and perform self-diagnosis for BCM.
Display of self-diagnosis results
NO DTC>> Replace IPDM E/R. Refer to
CAN COMM CIRCUIT>> Refer to
Inspection Using CONSULT-II (Self-Diagnosis)"
.
When lighting switch is in
OFF position
: HEAD LAMP SW 1 OFF
: HEAD LAMP SW 2 OFF
SKIA5200E
SKIA1039E
HEADLAMP (FOR USA)
LT-25
C
D
E
F
G
H
I
J
L
M
A
B
LT
2006 Pathfinder
Aiming Adjustment
EKS00FUG
For details, refer to the regulations in your area.
NOTE:
If vehicle front body has been repaired and /or the headlamp assembly has been replaced, check headlamp
aiming.
●
Before performing aiming adjustment, check the following:
–
Confirm headlamp aiming switch is set to "0" (zero) position.
–
Ensure all tires are inflated to correct pressure.
–
Place vehicle and screen on level surface.
–
Ensure there is no load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant and engine oil filled to correct level, and fuel tank full.
–
Confirm spare tire, jack and tools are properly stowed.
–
Aim each headlamp individually and ensure other headlamp beam pattern is blocked from screen.
–
Use adjusting screw to perform aiming adjustment
LKIA0568E
LT-26
HEADLAMP (FOR USA)
2006 Pathfinder
LOW BEAM AND HIGH BEAM
Aiming Chart
NOTE:
●
By regulation, no means for horizontal aim adjustment is provided from the factory; only vertical aim is
adjustable.
●
Basic illuminating area for evaluation and/or adjustment should be within range shown on aiming chart.
1.
Use adjustment screw to perform aiming adjustment.
●
Cover the opposite lamp and ensure fog lamps, if equipped, are turned off.
CAUTION:
Do not tighten adjustment screw beyond specified torque or damage may occur.
2.
Adjust beam pattern until cut-off line (top edge of illumination area) is positioned at the specified height off
ground. Measure cut-off line within distance J on H-line. See aiming chart.
WKIA4885E
1
Adjustment screen
2
Headlamp bulb center (HV point)
A
Minimum acceptable vertical aim
dimension (see aiming chart)
B
Maximum acceptable vertical aim
dimension (see aiming chart)
C
H-V point
D
Distance of headlamp aiming
screen from vehicle 7.62 m (25 ft.)
E
Maximum aim evaluation distance
from vertical center on aiming
screen 399mm (3
°
R).
F
Minimum aim evaluation distance
from vertical center on aiming
screen 133 mm (1
°
R)
G
Aim evaluation area
H
Horizontal aiming evaluation line.
Þ
Right
A (Minimum acceptable vertical aim dimension)
-3.3 mm (0.13 in)
0.025
°
up
B (Maximum acceptable vertical aim dimension)
36.6 mm (1.44 in)
0.275
°
down
Adjustment torque
1.67 N.m (17 kg-cm, 14.8 in-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст