Nissan Pathfinder (2006 year). Manual — part 50
TROUBLE DIAGNOSIS
ATC-65
C
D
E
F
G
H
I
K
L
M
A
B
ATC
2006 Pathfinder
COMPONENT DESCRIPTION
Air Mix Door Motors
The air mix door motor (passenger) (1) and the air mix door motor (driver) (2) are attached to the front heater
& cooling unit assembly. The air mix door motor (rear) is attached to the rear heater & cooling unit assembly.
These motors rotate so that the air mix door is opened or closed to a position set by the front (or rear) air con-
trol. Motor rotation is then conveyed through a shaft and the air mix door position is then fed back to the front
air control by the PBR built into the air mix door motors.
⇐
: Front
DIAGNOSTIC PROCEDURE FOR AIR MIX DOOR MOTOR (DRIVER)
1.
CHECK RESULT FROM FRONT AIR CONTROL SELF-DIAGNOSIS
Is self-diagnosis code 22 is present. Refer to
ATC-51, "A/C System Self-diagnosis Function"
.
YES or NO
YES
>> GO TO 2.
NO
>> GO TO 3.
WJIA1978E
WJIA1979E
WJIA1245E
ATC-66
TROUBLE DIAGNOSIS
2006 Pathfinder
2.
CHECK POWER SUPPLY CIRCUITS FOR AIR MIX DOOR MOTOR (DRIVER)
1.
Turn ignition switch OFF.
2.
Disconnect front air control connector and air mix door motor
(driver) connector.
3.
Check continuity between front air control harness connector
M49 terminal 2 and 3 and air mix door motor (driver) harness
connector M147 terminal 5 and 6.
OK or NG
OK
>> Replace air mix door motor (driver). Refer to
"FRONT AIR MIX DOOR MOTOR (PASSENGER)"
NG
>> Repair or replace harness as necessary.
3.
CHECK PBR REFERENCE SIGNAL VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect the air mix door motor (driver) connector.
3.
Turn ignition switch ON.
4.
Check voltage between air mix door motor (driver) harness con-
nector M147 terminal 3 and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
CHECK PBR REFERENCE VOLTAGE CIRCUIT BETWEEN AIR MIX DOOR MOTOR (DRIVER) AND
FRONT AIR CONTROL
1.
Turn ignition switch OFF.
2.
Disconnect the front air control connector.
3.
Check continuity between air mix door motor (driver) harness
connector M147 terminal 3 and front air control harness connec-
tor M49 terminal 23.
OK or NG
OK
>> Replace front air control. Refer to
.
NG
>> Repair or replace harness as necessary.
5.
CHECK PBR GROUND REFERENCE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the front air control connector.
3.
Check continuity between air mix door motor (driver) harness
connector M147 terminal 1 and front air control harness connec-
tor M49 terminal 26.
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace harness as necessary.
2 - 5
: Continuity should exist.
3 - 6
: Continuity should exist.
WJIA1092E
3 - Ground
: Approx. 5V
WJIA1246E
3 - 23
: Continuity should exist.
WJIA1093E
1 - 26
: Continuity should exist.
WJIA1247E
TROUBLE DIAGNOSIS
ATC-67
C
D
E
F
G
H
I
K
L
M
A
B
ATC
2006 Pathfinder
6.
CHECK PBR FEEDBACK SIGNAL
1.
Reconnect the front air control connector and air mix door motor
(driver) connector.
2.
Turn ignition switch ON.
3.
Check voltage between front air control harness connector M49
terminal 22 and ground.
4.
Rotate driver temperature control dial through complete range.
OK or NG
OK
>> Replace front air control. Refer to
.
NG
>> GO TO 7.
7.
CHECK PBR FEEDBACK CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the air mix door motor (driver) connector and front
air control connector.
3.
Check continuity between air mix door motor (driver) harness
connector M147 terminal 2 and front air control harness connec-
tor M49 terminal 22.
OK or NG
OK
>> Replace air mix door motor (driver). Refer to
"FRONT AIR MIX DOOR MOTOR (PASSENGER)"
NG
>> Repair or replace harness as necessary.
DIAGNOSTIC PROCEDURE FOR AIR MIX DOOR MOTOR (PASSENGER)
1.
CHECK RESULT FROM FRONT AIR CONTROL SELF-DIAGNOSIS
Self-diagnosis code 12 is present. Refer to
ATC-51, "A/C System Self-diagnosis Function"
YES or NO
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK POWER SUPPLY CIRCUIT FOR AIR MIX DOOR MOTOR (PASSENGER)
1.
Turn ignition switch OFF.
2.
Disconnect front air control connector and air mix door motor
(passenger) connector.
3.
Check continuity between front air control harness connector
M49 terminal 15 and 16 and air mix door motor (passenger) har-
ness connector M143 terminal 6 and 5.
OK or NG
OK
>> Replace air mix door motor (passenger). Refer to
145, "FRONT AIR MIX DOOR MOTOR (DRIVER)"
.
NG
>> Repair or replace harness as necessary.
22 - Ground
: Approx. 0V - 5V
WJIA1096E
2 - 22
Continuity should exist.
WJIA1248E
15 - 6
Continuity should exist.
16 - 5
Continuity should exist.
WJIA1097E
ATC-68
TROUBLE DIAGNOSIS
2006 Pathfinder
3.
CHECK PBR REFERENCE SIGNAL VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect the air mix door motor (passenger) connector.
3.
Turn ignition switch ON.
4.
Check voltage between air mix door motor (passenger) harness
connector M143 terminal 1 and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
CHECK PBR REFERENCE VOLTAGE CIRCUIT BETWEEN AIR MIX DOOR (PASSENGER) AND
FRONT AIR CONTROL
1.
Turn ignition switch OFF.
2.
Disconnect the front air control connector.
3.
Check continuity between air mix door motor (passenger) har-
ness connector M143 (B) terminal 1 and front air control harness
connector M49 (A) terminal 23.
OK or NG
OK
>> Replace front air control. Refer to
NG
>> Repair or replace harness as necessary.
5.
CHECK PBR GROUND REFERENCE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the front air control connector.
3.
Check continuity between air mix door motor (passenger) har-
ness connector M143 (B) terminal 3 and front air control harness
connector M49 (A) terminal 26.
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace harness as necessary.
Terminals
Condition
Voltage
(Approx.)
(+)
(-)
Air mix door motor
(passenger) con-
nector
Terminal No.
M143
1
Ground
Air mix door
(passenger)
5V
WJIA1682E
A
B
Connector
Terminal Connector
Terminal
Continuity
Front air control:
M49
23
Air mix door motor
(passenger):
M143
1
Yes
WJIA1656E
A
B
Connector
Terminal Connector
Terminal
Continuity
Front air control:
M49
26
Air mix door motor
(passenger):
M143
3
Yes
WJIA1650E
TROUBLE DIAGNOSIS
ATC-69
C
D
E
F
G
H
I
K
L
M
A
B
ATC
2006 Pathfinder
6.
CHECK PBR FEEDBACK SIGNAL
1.
Reconnect the front air control connector and air mix door motor
(passenger) connector.
2.
Turn ignition switch ON.
3.
Check voltage between front air control harness connector M50
terminal 36 and ground.
4.
Rotate passenger temperature control dial through complete
range.
OK or NG
OK
>> Replace front air control. Refer to
.
NG
>> GO TO 7.
7.
CHECK PBR FEEDBACK CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the air mix door motor (passenger) connector and
front air control connector.
3.
Check continuity between air mix door motor (passenger) har-
ness connector M143 terminal 2 and front air control harness
connector M50 terminal 36.
OK or NG
OK
>> Replace air mix door motor (passenger). Refer to
145, "FRONT AIR MIX DOOR MOTOR (DRIVER)"
.
NG
>> Repair or replace harness as necessary.
DIAGNOSTIC PROCEDURE FOR AIR MIX DOOR MOTOR (REAR)
1.
CHECK RESULT FROM FRONT AIR CONTROL SELF-DIAGNOSIS
Is self-diagnosis code 38 is present. Refer to
ATC-51, "A/C System Self-diagnosis Function"
.
YES or NO
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK POWER SUPPLY CIRCUIT FOR AIR MIX DOOR MOTOR (REAR)
1.
Turn ignition switch OFF.
2.
Disconnect front air control connector and air mix door motor
(rear) connector.
3.
Check continuity between front air control harness connector
M49 terminal 17 and air mix door motor (rear) harness connec-
tor B155 terminal 6 and between front air control harness con-
nector M49 terminal 18 and air mix door motor (rear) harness
connector B155 terminal 1.
OK or NG
OK
>> Replace air mix door motor (rear). Refer to
ATC-146, "REAR AIR MIX DOOR MOTOR"
NG
>> Repair or replace harness as necessary.
36 - Ground
: Approx. 0 - 5V
WJIA1249E
2 - 36
: Continuity should exist.
WJIA1101E
17 - 6
Continuity should exist.
18 - 1
Continuity should exist.
WJIA1102E
ATC-70
TROUBLE DIAGNOSIS
2006 Pathfinder
3.
CHECK PBR REFERENCE SIGNAL VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect the air mix door motor (rear) connector.
3.
Turn ignition switch ON.
4.
Check voltage between air mix door motor (rear) harness con-
nector B155 terminal 3 and ground.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 4.
4.
CHECK PBR REFERENCE VOLTAGE CIRCUIT BETWEEN AIR MIX DOOR MOTOR (REAR) AND
FRONT AIR CONTROL
1.
Turn ignition switch OFF.
2.
Disconnect the front air control connector.
3.
Check continuity between air mix door motor (rear) harness con-
nector B155 terminal 3 and front air control harness connector
M49 terminal 23.
OK or NG
OK
>> Replace front air control. Refer to
.
NG
>> Repair or replace harness as necessary.
5.
CHECK PBR GROUND REFERENCE CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the front air control connector.
3.
Check continuity between air mix door motor (rear) harness con-
nector B155 terminal 2 and front air control harness connector
M49 terminal 26.
OK or NG
OK
>> GO TO 6.
NG
>> Repair or replace harness as necessary.
6.
CHECK PBR FEEDBACK SIGNAL
1.
Reconnect the front air control connector and air mix door motor
(rear) connector.
2.
Turn ignition switch ON.
3.
Check voltage between front air control harness connector M49
terminal 25 and ground.
4.
Rotate rear temperature and mode control dial through complete
range.
OK or NG
OK
>> Replace front air control. Refer to
.
NG
>> GO TO 7.
3 - Ground
: Approx. 5V
LJIA0050E
3 - 23
Continuity should exist.
WJIA1103E
2 - 26
Continuity should exist.
WJIA1104E
25 - Ground
: Approx. 0 - 5V
WJIA1105E
TROUBLE DIAGNOSIS
ATC-71
C
D
E
F
G
H
I
K
L
M
A
B
ATC
2006 Pathfinder
7.
CHECK PBR FEEDBACK CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect the air mix door motor (rear) connector and front air
control connector.
3.
Check continuity between air mix door motor (rear) harness con-
nector B155 terminal 4 and front air control harness connector
M49 terminal 25.
OK or NG
OK
>> Replace air mix door motor (rear). Refer to
.
NG
>> Repair or replace harness as necessary.
4 - 25
Continuity should exist.
WJIA1106E
ATC-72
TROUBLE DIAGNOSIS
2006 Pathfinder
Intake Door Motor Circuit
EJS004P7
SYMPTOM:
●
Intake door does not change.
●
Intake door motor does not operate normally.
INSPECTION FLOW
*1
ATC-53, "Operational Check (Front)"
*2
ATC-51, "A/C System Self-diagno-
sis Function"
*3
ATC-52, "SELF-DIAGNOSIS CODE
CHART"
WJIA1053E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст