Nissan Pathfinder (2006 year). Manual — part 362
REAR DRIVE SHAFT
RAX-11
C
E
F
G
H
I
J
K
L
M
A
B
RAX
2006 Pathfinder
5.
Insert the specified quantity of Genuine NISSAN Grease or
equivalent, onto the housing (indicated by * marks), and install it
onto shaft. Refer to
MA-11, "Fluids and Lubricants"
6.
Install the stopper ring onto the housing.
7.
After installation, pull on the shaft to check engagement between the joint sub-assembly and the stopper
ring.
8.
Install the boot securely into the grooves (indicated by * marks)
as shown.
CAUTION:
If there is grease on boot mounting surfaces (indicated by*
marks) of shaft and housing, boot may come off. Remove
all grease from surfaces.
9.
Check that the boot installation length “L” is the length indicated
below. Insert a flat-bladed screwdriver or similar tool into larger
side of boot. Bleed the air from the boot to prevent any boot
deformation.
CAUTION:
●
The boot may break if the boot installation length is less than the specified value.
●
Do not to touch the tip of the screwdriver to the inside of the boot.
10. Secure the large and small ends of the boot with the new boot
bands as shown.
NOTE:
Discard the old boot bands and use new ones for assembly.
11. After installing the housing and shaft, rotate the boot to check that the boot is positioned correctly. If the
boot is not positioned correctly, reposition the boot and secure the boot using a new boot band.
Wheel Side
1.
Insert the Genuine NISSAN Grease or equivalent, into the joint
sub-assembly serration hole until the grease begins to ooze
from the ball groove and serration hole. Refer to
. After inserting the grease, use a shop cloth to
wipe off the grease that has oozed out.
Grease capacity
: 155
−
175 g (5.47
−
6.17 oz)
RAC0678D
Boot installation length “L ”
: 148.7 mm (5.85 in)
WDIA0287E
SFA395
SDIA1127E
RAX-12
REAR DRIVE SHAFT
2006 Pathfinder
2.
Wind the serrated part of the shaft with tape. Install the boot
band and boot onto the shaft. Do not damage the boot.
NOTE:
Discard the old boot band and boot and use a new one for
assembly.
3.
Remove the protective tape wound around the serrated part of
the shaft.
4.
Attach the circlip to the shaft. The circlip must fit securely into
the shaft groove. Attach the nut to the joint sub-assembly.
Use a soft hammer to press-fit the circlip.
NOTE:
Discard the old circlip and use a new one for assembly.
5.
Insert the specified quantity of Genuine NISSAN Grease or
equivalent, into the housing from the large end of the boot. Refer
to
MA-11, "Fluids and Lubricants"
.
6.
Install the boot securely into the grooves (indicated by the *
marks) as shown.
CAUTION:
If there is grease on the boot mounting surfaces (indicated
by the * marks) of the shaft and housing, the boot may
come off. Remove all grease from the shaft surfaces.
7.
Check that the boot installation length “L” is the specified length.
Insert a flat-bladed screwdriver or similar tool into the larger side
of the boot. Bleed the air from the boot to prevent boot deforma-
tion.
CAUTION:
●
The boot may break if the boot installation length is less than the specified length.
●
Do not contact inside surface of boot with the tip of the screwdriver.
8.
Secure the large and small ends of the boot using new boot
bands as shown.
NOTE:
Discard the old boot bands and use new ones for assembly.
9.
After installing the joint sub-assembly and shaft, rotate the boot to check that it is positioned correctly. If
the boot is not positioned correctly, reposition the boot and secure the boot using a new boot band.
SFA800
Grease capacity
: 155
−
175 g (5.47
−
6.17 oz)
RAC0049D
Boot installation length “L”
: 143 mm (5.63 in)
WDIA0288E
SFA395
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-13
C
E
F
G
H
I
J
K
L
M
A
B
RAX
2006 Pathfinder
SERVICE DATA AND SPECIFICATIONS (SDS)
PFP:00030
Wheel Bearing
EDS003AR
Drive Shaft
EDS003AS
Measurement of spring scale
Less than 26.6 N (2.7 kg, 5.95 lb)
Axial end play
0 mm (0 in)
Joint
Wheel side
Final drive side
Grease capacity
155
−
175 g
(5.47
−
6.17 oz)
155
−
175 g
(5.47
−
6.17 oz)
Boot installed length
143 mm (5.63 in)
148.7 mm (5.85 in)
RAX-14
SERVICE DATA AND SPECIFICATIONS (SDS)
2006 Pathfinder
RF-1
ROOF
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION
A
B
RF
2006 Pathfinder
PRECAUTIONS . . . . . . . . . . . . . . .. 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special service tool . . . . . . . . . . . . .. 3
Commercial Service Tool . . . . . . . . . . . 3
SQUEAK AND RATTLE TROUBLE DIAGNOSES . . 4
Work Flow . . . . . . . . . . . . . . . . 4
Generic Squeak and Rattle Troubleshooting . . ... 6
Diagnostic Worksheet . . . . . . . . . . . .. 8
SUNROOF . . . . . . . . . . . . . . . . 10
Component Parts and Harness Connector Location
System Description . . . . . . . . . . . . 10
OUTLINE . . . . . . . . . . . . . . . . 10
OPERATION . . . . . . . . . . . . . . 10
CONSULT-II OPERATION . . . . . . . . ... 16
GAP ADJUSTMENT . . . . . . . . . . . 23
HEIGHT DIFFERENCE ADJUSTMENT . . . .. 23
RF-2
PRECAUTIONS
2006 Pathfinder
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EIS007SU
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions
EIS007SV
●
Disconnect both battery cables in advance.
●
Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
●
Be careful not to scratch pad and other parts.
●
When removing or disassembling any part, be careful not to damage or deform it. Protect parts which may
get in the way with cloth.
●
When removing parts with a screwdriver or other tool, protect parts by wrapping them with vinyl or tape.
●
Keep removed parts protected with cloth.
●
If a clip is deformed or damaged, replace it.
●
If an unreusable part is removed, replace it with a new one.
●
Tighten bolts and nuts firmly to the specified torque.
●
After re-assembly has been completed, make sure each part functions correctly.
●
Remove stains in the following way.
Water-soluble stains:
Dip a soft cloth in warm water, and then squeeze it tightly. After wiping the stain, wipe with a soft dry cloth.
Oil stain:
Dissolve a synthetic detergent in warm water (density of 2 to 3% or less), dip the cloth, then clean off the stain
with the cloth. Next, dip the cloth in fresh water and squeeze it tightly. Then clean off the detergent completely.
Then wipe the area with a soft dry cloth.
●
Do not use any organic solvent, such as thinner or benzine.
PREPARATION
RF-3
C
D
E
F
G
H
J
K
L
M
A
B
RF
2006 Pathfinder
PREPARATION
PFP:00002
Special service tool
EIS007SW
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
EIS007SX
Tool number
(Kent-Moore No.)
Tool name
Description
—
(J-39570)
Chassis ear
Locating the noise
—
(J-43980)
NISSAN Squeak and
Rattle Kit
Repairing the cause of noise
SIIA0993E
SIIA0994E
(Kent-Moore No.)
Tool name
Description
(J-39565)
Engine ear
Locating the noise
SIIA0995E
RF-4
SQUEAK AND RATTLE TROUBLE DIAGNOSES
2006 Pathfinder
SQUEAK AND RATTLE TROUBLE DIAGNOSES
PFP:00000
Work Flow
EIS007SY
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer's comments; refer to
. This information is necessary to duplicate the
conditions that exist when the noise occurs.
●
The customer may not be able to provide a detailed description or the location of the noise. Attempt to
obtain all the facts and conditions that exist when the noise occurs (or does not occur).
●
If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer
is concerned about. This can be accomplished by test driving the vehicle with the customer.
●
After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
●
Squeak —(Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard sur-
faces = higher pitch noise/softer surfaces = lower pitch noises/edge to surface = chirping.
●
Creak—(Like walking on an old wooden floor)
Creak characteristics include firm contact/slow movement/twisting with a rotational movement/pitch
dependent on materials/often brought on by activity.
●
Rattle—(Like shaking a baby rattle)
Rattle characteristics include the fast repeated contact/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
●
Knock —(Like a knock on a door)
Knock characteristics include hollow sounding/sometimes repeating/often brought on by driver action.
●
Tick—(Like a clock second hand)
Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
●
Thump—(Heavy, muffled knock noise)
Thump characteristics include softer knock/dead sound often brought on by activity.
●
Buzz—(Like a bumble bee)
Buzz characteristics include high frequency rattle/firm contact.
●
Often the degree of acceptable noise level will vary depending upon the person. A noise that you may
judge as acceptable may be very irritating to the customer.
●
Weather conditions, especially humidity and temperature, may have a great effect on noise level.
SBT842
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст