Nissan Pathfinder (2006 year). Manual — part 93
REMOTE KEYLESS ENTRY SYSTEM
BL-45
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
Schematic
EIS007OY
WIWA1623E
BL-46
REMOTE KEYLESS ENTRY SYSTEM
2006 Pathfinder
Wiring Diagram — KEYLES —
EIS007OZ
WIWA1613E
REMOTE KEYLESS ENTRY SYSTEM
BL-47
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
WIWA1628E
BL-48
REMOTE KEYLESS ENTRY SYSTEM
2006 Pathfinder
Terminals and Reference Value for BCM
EIS007P0
BCS-12, "Terminals and Reference Values for BCM"
WIWA1614E
REMOTE KEYLESS ENTRY SYSTEM
BL-49
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
Terminals and Reference Value for IPDM E/R
EIS007P1
Refer to
PG-28, "Terminals and Reference Values for IPDM E/R"
.
BL-50
REMOTE KEYLESS ENTRY SYSTEM
2006 Pathfinder
CONSULT-II Function (BCM)
EIS007P2
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II Inspection Procedure
EIS007P3
“MULTI REMOTE ENT”
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1.
Turn ignition switch OFF.
2.
Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
3.
Turn ignition switch ON.
4.
Touch “START (NISSAN BASED VHCL)".
5.
Touch “BCM”.
If "BCM" is not indicated, refer to
BCM diagnostic
test item
Diagnostic mode
Description
Inspection by part
WORK SUPPORT
Supports inspections and adjustments. Commands are transmitted to the BCM
for setting the status suitable for required operation, input/output signals are
received from the BCM and received data is displayed.
DATA MONITOR
Displays BCM input/output data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS
Displays BCM self-diagnosis results.
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER
BCM part number can be read.
CONFIGURATION
Performs BCM configuration read/write functions.
BBIA0538E
BCIA0029E
BCIA0030E
REMOTE KEYLESS ENTRY SYSTEM
BL-51
C
D
E
F
G
H
J
K
L
M
A
B
BL
2006 Pathfinder
6.
Touch “MULTI REMOTE ENT”.
7.
Select diagnosis mode.
“DATA MONITOR”, “ACTIVE TEST” and “WORK SUPPORT”
are available.
CONSULT-II Application Items
EIS007P4
“MULTI REMOTE ENT”
Data Monitor
Active Test
LIIA0194E
BCIA0031E
Monitored Item
Description
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch RH.
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch LH.
BACK DOOR SW
Indicates [ON/OFF] condition of back door switch.
KEY ON SW
Indicates [ON/OFF] condition of key switch.
ACC ON SW
Indicates [ON/OFF] condition of ignition switch in ACC position.
IGN ON SW
Indicates [ON/OFF] condition of ignition switch in ON position.
KEYLESS PANIC
Indicates [ON/OFF] condition of panic signal from keyfob.
KEYLESS UNLOCK
Indicates [ON/OFF] condition of unlock signal from keyfob.
KEYLESS LOCK
Indicates [ON/OFF] condition of lock signal from keyfob.
KEY CYL LK-SW
Indicates [ON/OFF] condition of lock signal from door key cylinder switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from lock/unlock switch.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from lock/unlock switch.
RKE LCK-UNLCK
Indicates [ON/OFF] condition of lock/unlock signal at the same time from keyfob.
RKE KEEP UNLK
Indicates [ON/OFF] condition of unlock signal from keyfob.
Test Item
Description
FLASHER
This test is able to check right and left hazard reminder operation. The right hazard lamp turns on
when “RH” on CONSULT-II screen is touched and the left hazard lamp turns on when "LH" on CON-
SULT-II screen is touched.
BL-52
REMOTE KEYLESS ENTRY SYSTEM
2006 Pathfinder
Work Support
*: Perform this mode always in the state of C mode. Refer to
BL-43, "Hazard and Horn Reminder"
HORN CHIRP SET*
*: Perform this mode always in the state of C mode. Refer to
BL-43, "Hazard and Horn Reminder"
HAZARD LAMP BACK SET*
*: Perform this mode always in the state of C mode. Refer to
BL-43, "Hazard and Horn Reminder"
MULTI ANSWER BACK SET
AUTO LOCK SET
PANIC ALARM SET
HORN
This test is able to check panic alarm and horn reminder operations. The alarm activate for 0.5 sec-
onds after “ON” on CONSULT-II screen is touched.
DOOR LOCK
This test is able to check door lock operation. The doors lock and unlock based on the item on CON-
SULT-II screen touched.
Test Item
Description
Test Item
Description
REMO CONT ID REGIST
Keyfob ID code can be registered.
REMO CONT ID ERASUR
Keyfob ID code can be erased.
REMO CONT ID CONFIR
It can be checked whether keyfob ID code is registered or not in this mode.
HORN CHIRP SET*
Horn chirp function mode can be changed in this mode. The function mode will be changed when
"CHANG SETT" on CONSULT-II screen is touched.
HAZARD LAMP SET*
Hazard lamp function mode can be changed in this mode. The function mode will be changed when
"CHANG SETT" on CONSULT-II screen is touched.
MULTI ANSWER BACK SET
Hazard and horn reminder mode can be changed in this mode. The reminder mode will be changed
when “CHANG SETT” on CONSULT-II screen is touched.
AUTO LOCK SET
Auto locking function mode can be changed in this mode. The function mode will be changed when
"CHANG SETT" on CONSULT-II screen is touched.
PANIC ALRM SET
Panic alarm operation mode can be changed in this mode. The operation mode will be changed
when "CHANG SETT" on CONSULT-II screen is touched.
Horn chirp function
ON
OFF
MODE1
MODE2
MODE3
MODE4
Hazard lamp operation mode
Nothing
Unlock only
Lock only
Lock and Unlock
MODE 1
(C mode)
MODE 2
(S mode)
Keyfob operation
Lock
Unlock
Lock
Unlock
Hazard warning lamp flash
Twice
Once
Twice
—
Horn sound
Once
—
—
—
MODE 1
MODE 2
MODE 3
Auto locking function
1 minutes
Nothing
5 minutes
MODE 1
MODE 2
MODE 3
Keyfob operation
0.5 seconds
Nothing
1.5 seconds
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст